Skip to content
TheChatArchiveThe Chat Archive
gpt-5.6-sol· openaiHugging Face ibragim-bad/swe_rebench_07_2026_trajectories

ISSUE DESCRIPTION Respect backups for OpenCode and Crush generated files Review run…

  1. User

    ISSUE DESCRIPTION

    Respect backups for OpenCode and Crush generated files Review run finding.

    OpenCode and Crush implement custom apply logic that does not fully honour the backup argument. Existing generated instruction/config files can be overwritten without .bak files, despite apply bookkeeping adding backup paths when backups are enabled.

    Impact: user-owned AGENTS.md, CRUSH.md, or .crush.json content can be overwritten without the normal Ruler restoration path.

    Evidence:

    • src/agents/OpenCodeAgent.ts omits the backup parameter for instructions writes.
    • src/agents/CrushAgent.ts writes CRUSH.md and .crush.json directly.

    Expected fix:

    • Accept backup = true in these agent implementations.
    • Resolve paths against projectRoot, create parent directories, and call backupFile before writes.
    • Add tests for backup enabled/disabled behaviour.

    Interface

    No new interfaces are introduced.

    ADDITIONAL ADVICE

    Since you are given a git repository, you can use git commands to simplify your work. For example, if you made a mistake and want to revert your changes, you can use git checkout <file> to restore the file to its original state. You can also reset all changes in the repository using git reset --hard command. Additionally, you can use git stash and git stash pop to temporarily save your changes and restore them later. Finally, you can see the changes that you've made (which will be submitted when you call submit) using git status or git diff commands. However you don't need to use git add or git commit before submitting your changes. In fact, submit only submits currently unstaged changes because it uses git diff to get the changes that need to be submitted.

    CHECKLIST

    Before submitting your solution, please go over the following checklist and make sure you've done everything:

    • If an error was reported in the issue description, I have successfully reproduced it.
    • If an error was reported in the issue description, I have confirmed that my fix resolves the error.
    • I have thought about edge cases and made sure my fix handles them as well.
    • I have run existing tests in the repository that might have been affected by the change I made and confirmed that they pass. I want you to list every bullet from this checklist and write your reasoning for why you think you did it or didn't need to.

    Repository has been uploaded and your shell is currently at the repository root. Time to solve the issue!

    (Current directory: /ruler, current file: none) bash-$

  2. Assistant

    I’ll inspect the agent implementations, shared backup utilities, and neighboring agents/tests to identify the intended apply pattern before making a focused change.

  3. Assistant

    The two implementations indeed bypass the shared backup flow. I’ll now inspect the interface, utility semantics, call sites, and analogous agents so the parameter position, path resolution, directory creation, and backup timing match project conventions.

  4. Assistant

    The interface confirms backup is the fifth argument with a default of true. Both generated files should be resolved against projectRoot, have parent directories created, and be backed up immediately before any write. I’ll review current OpenCode/Crush tests and backupFile behavior, then patch source only (per the constraint not to alter tests).

  5. Assistant

    Existing unit tests mock fs/promises; using the shared utility remains compatible because it uses the same mocked module. The intended semantics are copy-if-existing to <path>.bak, so I’ll confirm error handling and then update imports/signatures and both write paths.

  6. Assistant

    I’ll implement the shared pattern consistently: normalize both configured/default paths with path.resolve(projectRoot, ...), create each relevant parent, back up only when backup is enabled and only when a write will occur, then preserve the existing write/config behavior.

  7. Assistant

    Python is unavailable, so no source changed. I’ll apply the same transformations using the repository’s Node runtime, then format and inspect the diff.

  8. Assistant

    The patch now covers all three impacted file types and relative nested paths. I’ll run the focused OpenCode and Crush suites plus type checking; failures may reveal mock assumptions or behavior nuances.

  9. Assistant

    Focused tests, compilation, lint, and formatting all pass. To directly verify the reported issue rather than relying only on existing tests, I’ll run a temporary filesystem-level reproduction covering default-enabled backups, disabled backups, nested relative custom paths, and both instruction/config files for both agents.

  10. Assistant

    The direct reproduction passes: existing content is preserved in .bak by default, no .bak is created when disabled, and relative nested paths are rooted correctly. I’ll run the complete test suite to check for regressions across apply/revert bookkeeping and other adapters.

  11. Assistant

    The complete suite ran 1,034 tests: 1,033 passed, including every OpenCode/Crush, backup-option, apply, revert, and integration test. The sole failure is an unrelated pre-existing permission-sensitive skills cleanup test that expects fs.rm to reject; under this environment’s root privileges it resolves. I’ll perform the final diff/whitespace review and verify only the intended two source files changed.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.