Skip to content
TheChatArchiveThe Chat Archive
Geminigemini-2.5-flash-preview-04-17· GoogleHugging Face LMArena Human Preference 140K

Prepare Risk assessment document for the following of CAPA: Brief Description of…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with o3-2025-04-16’s answer.
  1. User

    Prepare Risk assessment document for the following of CAPA: Brief Description of Non-Conformity Customer reported that “Pharmacy reported a complaint from patient: improper blister sealing and crushed tablets for 2 units. Root cause Analysis/Justification for CAPA There might be the chance that due to interrupted chilled water supply to CSR, during blister operation CSR get hot due to low chilling and heat transfer from sealing roller, due to which forming side of the blister web get stick to CSR and drag of both side of blister occurs due to which blister pocket get damaged and tablets get crushed. Same was missed by machine operator and same blisters were get packed into carton. Description of proposed CAPA Chilled water temperature interlock and chilled water flow interlock shall be installed on blister pack machine. When chilled water temperature goes out of limit or supply get interrupted then machine will get automatically stops and give alarm.

  2. Gemini Assistant

    Okay, here is a draft Risk Assessment document specifically tailored for the CAPA you've described.

    This document follows a standard structure for risk assessment in a manufacturing/quality context, often used in pharmaceutical or medical device industries.


    RISK ASSESSMENT DOCUMENT

    Document Title: Risk Assessment for CAPA 12345 - Blister Sealing/Crushed Tablet Issue Document Number: RA-CAPA-12345 (Assign a unique number) Version: 1.0 Effective Date: [Date] Review Date: [Date + 1 Year or as per procedure]

    1. Purpose and Scope

    This document details the risk assessment performed for Corrective Action/Preventive Action (CAPA) 12345, raised to address customer complaints regarding improper blister sealing and crushed tablets. The scope of this assessment focuses on the identified root cause related to chilled water supply to the cooling cylinder (CSR) of the blister packing machine and the proposed CAPA (installation of temperature and flow interlocks).

    2. Reference Documents

    • Non-Conformity Report / Complaint Record No.: [e.g., NC-67890, CM-54321]
    • CAPA Plan No.: CAPA-12345
    • [Relevant Standard Operating Procedures for Blister Packing, Maintenance, Quality Control, Risk Management]

    3. Risk Assessment Team

    The risk assessment was performed by the following individuals/functions:

    • [Name/Title], Originator / CAPA Owner (e.g., Manufacturing Supervisor, Engineering)
    • [Name/Title], Quality Assurance Representative
    • [Name/Title], Engineering Representative
    • [Name/Title], Operations / Machine Subject Matter Expert

    4. Methodology

    This risk assessment utilizes a qualitative approach based on the likelihood of the hazard occurring and the severity of the potential harm or impact.

    • Severity (S): The degree of impact or harm if the event occurs.
      • High (H): Severe impact (e.g., significant patient safety risk, major product recall, critical non-compliance, significant business loss).
      • Medium (M): Moderate impact (e.g., potential patient impact but not severe, product rework/scrap, minor non-compliance, moderate business impact).
      • Low (L): Minor impact (e.g., no patient impact, minor product defect, minor deviation, minimal business impact).
    • Likelihood (L): The probability of the event occurring.
      • High (H): Very likely to occur (e.g., frequent occurrence).
      • Medium (M): Likely to occur (e.g., occasional occurrence).
      • Low (L): Unlikely to occur (e.g., rare occurrence).
      • Very Low (VL): Extremely unlikely to occur (e.g., almost impossible).
    • Risk Level: Determined by the combination of Severity and Likelihood.
      • High Risk: H x H, H x M, M x H
      • Medium Risk: H x L, M x M, L x H
      • Low Risk: M x L, L x M, L x L, H x VL, M x VL, L x VL

    (Note: An RPN (Risk Priority Number) calculation (Severity x Occurrence x Detectability) could also be used if preferred, requiring a Detectability score). For this simple CAPA, S x L provides sufficient clarity before and after the proposed action.

    5. Hazard Identification and Risk Assessment (Before CAPA)

    Process Step / AreaPotential Failure Mode (Hazard)Potential CausePotential Effect / HarmSeverity (S)Likelihood (L) (Before CAPA)Initial Risk Level
    Blister SealingImproper blister sealing and crushed tabletsInsufficient cooling of CSR due to interrupted or low flow/temperature chilled water supply. Heat transfer from sealing roller causes forming web to stick/drag on overheated CSR.- Defective blister pockets (damaged, torn, poor seal)- Tablets crushed within pockets- Packaging of visibly/non-visibly defective units into finished product- Customer complaints- Potential impact on product quality, stability, and possibly efficacy if container integrity is compromised- Reputational damage, Recall possibilityHigh (H)Medium (M)High
    InspectionFailure of operator to detect all occurrences of improper sealing/crushed tablets during in-process checks.Visual inspection limitations, high line speed, fatigue, variability in defect appearance.Defective product released to market, reaching the patient.High (H)Medium (M)High

    Summary of Initial Risk: The initial risk associated with insufficient CSR cooling leading to defective blisters and subsequent release to the market is considered High due to the potential impact on product quality and the ability of defects to escape detection.

    6. Existing Risk Controls (Before CAPA)

    • Visual inspection by the machine operator during the production run.
    • Quality Control checks on finished product batches (may not detect all unit-level defects).

    (Note: The non-conformity report indicates the existing control (operator inspection) was not effective in preventing the release of the specific defective units.)

    7. Proposed Risk Mitigation (CAPA)

    The proposed CAPA (CAPA-12345) is the installation of:

    • Chilled water temperature interlock on the blister pack machine.
    • Chilled water flow interlock on the blister pack machine.

    Functionality:

    • When the chilled water temperature goes out of the defined limit, the machine will automatically stop and give an alarm.
    • When the chilled water flow is interrupted or goes below the defined limit, the machine will automatically stop and give an alarm.

    8. Risk Re-assessment (After CAPA Implementation)

    Process Step / AreaPotential Failure Mode (Hazard)Potential CauseProposed Mitigation (CAPA)Effectiveness of MitigationSeverity (S)Likelihood (L) (After CAPA)Residual Risk Level
    Blister SealingImproper blister sealing / crushed tabletsInsufficient cooling of CSR due to interrupted or low flow/temperature chilled water.Installation of temperature and flow interlocks that automatically stop the machine and alarm if chilled water parameters are outside specification.Highly effective in preventing the machine from operating under conditions known to cause the defect. Addresses the root cause directly by stopping production of defective units.High (H)Very Low (VL)Low
    InspectionFailure to detect defectsN/A (Root cause addressed upstream)N/A (The CAPA prevents the creation of defects under this specific failure mode, making detection of this specific defect cause unnecessary during operation under control)Addresses the problem at the source, reducing reliance on downstream detection for this specific failure mode.High (H)Very Low (VL)Low

    Summary of Residual Risk: After the successful implementation and verification of the proposed CAPA (interlocks), the likelihood of producing defective blisters due to insufficient CSR cooling is significantly reduced as the machine will stop before defects are created under these conditions. The residual risk is therefore considered Low.

    9. Conclusion

    The initial risk associated with improper blister sealing and crushed tablets caused by insufficient chilled water supply to the CSR was assessed as High. The proposed CAPA (installation of chilled water temperature and flow interlocks) is a robust solution that addresses the identified root cause by preventing the machine from operating under conditions that would lead to these defects.

    The implementation of this CAPA is expected to reduce the likelihood of the failure mode occurring and resulting in defective product being produced, thereby lowering the residual risk to an acceptable level (Low).

    It is critical that the implementation of the CAPA is verified for effectiveness (e.g., by testing the interlock functionality).

    10. Approvals

    RoleName / SignatureDate
    Originator / Owner
    Quality Assurance
    Engineering
    Management Approval

    Disclaimer: This is a template based on the information provided. You will need to adapt it to your specific company's procedures, document numbering system, and risk matrix definitions. Ensure the Severity and Likelihood ratings align with your company's established guidelines.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.