Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen-max-2025-01-25· Alibaba (Qwen)Hugging Face LMArena Human Preference 140K

I have a piece of wood that is 80 cm x 30 cm x 2 cm . I'd like to mount it on the wall,…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Mistralmistral-medium-2505’s answer.
  1. User

    I have a piece of wood that is 80 cm x 30 cm x 2 cm . I'd like to mount it on the wall, as a shelf. I have two supports for the shelf.

    How would you place the supports and why? I wanted to place them 10 cm from the extremities. So that one has, from left to right: left end, 10 cm nothing, then comes the support, 60 cm nothing, another support, 10 cm nothing, right end.

    But I am unsure if 10 cm from the extremities is the best for load support, hence the question.

  2. Qwen Assistant

    Your initial plan to place the supports 10 cm from the extremities is a good starting point, but there are structural and load-bearing considerations that can help optimize the placement for maximum strength and stability. Let’s break this down:


    Key Considerations

    1. Load Distribution: The goal is to distribute the weight of the shelf and its contents evenly across the supports to minimize stress on any one part of the shelf.
    2. Deflection (Bending): A shelf tends to bend or sag under load, especially in the middle. Properly placed supports reduce the bending moment and ensure the shelf remains level.
    3. Overhang: The amount of overhang (shelf extending beyond the supports) affects how much weight the shelf can bear without tipping or bending excessively.

    Optimal Support Placement

    For a rectangular shelf like yours (80 cm long), the general rule of thumb is to place the supports at the quarter points of the shelf's length. This means:

    • Divide the shelf into four equal sections: 80 cm÷4=20 cm80 \, \text{cm} \div 4 = 20 \, \text{cm}.
    • Place the supports 20 cm from each end.

    This placement ensures:

    • The middle section of the shelf (where bending is most likely to occur) is well-supported.
    • The overhang on each side is minimized, reducing the risk of tipping or excessive bending.

    So, your support placement would look like this:

    • From left to right: left end, 20 cm nothing, support, 40 cm nothing, support, 20 cm nothing, right end.

    Why Not 10 cm from the Extremities?

    Placing the supports 10 cm from the ends creates a larger unsupported span in the middle (60 cm). While this setup might still work for light loads, it increases the bending moment and deflection in the center of the shelf, which could lead to sagging over time. Additionally, the 10 cm overhang on each side might make the shelf more prone to tipping if heavier items are placed near the edges.


    Additional Tips

    1. Material Strength: Your shelf is made of wood, which has some flexibility. However, thinner wood (like your 2 cm thickness) is more prone to bending under heavy loads. Ensure the supports are securely mounted to handle the expected weight.
    2. Mounting the Supports: Use sturdy brackets or L-shaped supports that are securely anchored into wall studs. If you can't anchor into studs, use heavy-duty wall anchors rated for the expected load.
    3. Load Capacity: Avoid placing extremely heavy objects on the shelf, especially near the edges. Distribute the weight evenly across the shelf for better stability.
    4. Edge Reinforcement: If you’re concerned about sagging, consider adding a small lip or decorative trim along the front edge of the shelf to increase rigidity.

    Conclusion

    The optimal placement for your supports is 20 cm from each end, leaving a 40 cm span between the supports. This configuration minimizes bending and ensures even weight distribution.

    Support placement: 20 cm from each end, with 40 cm between supports.\boxed{\text{Support placement: 20 cm from each end, with 40 cm between supports.}}

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.