Skip to content
TheChatArchiveThe Chat Archive
Googlegemma-3-27b-it· GoogleHugging Face LMArena Human Preference 140K

The FreeCAD has the "Maximum angular deflection" setting affecting how accurately 3d…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Claudeclaude-sonnet-4-20250514’s answer.
  1. User

    The FreeCAD has the "Maximum angular deflection" setting affecting how accurately 3d shapes are shown in UI. With default deflection setting of 28 degrees I observe noticeable roughness in the arched surfaces. What's recommended value for this setting?

  2. Google Assistant

    You're right to notice that the "Maximum angular deflection" setting in FreeCAD significantly impacts the smoothness of curved surfaces displayed in the UI. The default of 28 degrees is often too high for visually pleasing results, especially on arches and complex curves. There's no single "recommended" value, as it depends on:

    • The complexity of your model: More complex curves need lower deflection angles.
    • Your hardware: Lower-end hardware will struggle with very low deflection angles (more polygons = more processing).
    • Your visual tolerance: How much roughness are you willing to accept?
    • The intended use of the model: For visualization, you'll want a lower angle than for a model used solely for calculations.

    However, here's a breakdown of recommended ranges and how to find the sweet spot, along with explanations:

    Understanding the Setting

    • What it does: This setting controls the maximum angle between adjacent facets used to approximate a curved surface. A lower angle means more facets, a smoother appearance, but also more polygons to render. A higher angle means fewer facets, a rougher appearance, but faster rendering.
    • Units: The angle is in degrees.
    • Where to find it: Edit > Preferences > Display > View > Maximum angular deflection (or View > Preferences > Display > View > Maximum angular deflection depending on your FreeCAD version). You can also set it per document in View > View Settings > Display. Document-level settings override global preferences.

    Recommended Values & Starting Points

    Here's a tiered approach, starting with conservative values and working down:

    • High Quality Visualization (and you have a decent GPU): 1-5 degrees. This will give you the smoothest possible appearance. Expect a performance hit, especially with large models. Start with 3 degrees and adjust. This is ideal for renderings or presentations.
    • Good Balance (most common use case): 5-10 degrees. This is a good starting point for most models. You'll get a significant improvement in smoothness over the default 28 degrees, without a huge performance penalty. I'd recommend starting at 7 degrees.
    • Moderate Quality (for less critical curves or weaker hardware): 10-15 degrees. This is a compromise. You'll still see some faceting, but it will be much less noticeable than the default. Good for quick previews or models with less emphasis on surface smoothness.
    • Fast Preview (for very large models or very weak hardware): 15-20 degrees. This is a last resort. The faceting will be quite visible, but it will allow you to work with the model without significant lag.

    How to Find Your Sweet Spot

    1. Start Low: Begin with 5 degrees.
    2. Zoom In: Zoom in on the arched surfaces you're concerned about. This will make the faceting more apparent.
    3. Rotate the View: Rotate the model to view the curves from different angles. Faceting can be more visible from certain perspectives.
    4. Increase Gradually: Slowly increase the "Maximum angular deflection" in increments of 1 degree. After each change, zoom in and rotate the view to assess the smoothness.
    5. Look for the Point of Diminishing Returns: You'll reach a point where increasing the angle further doesn't significantly improve the appearance, but does noticeably impact performance. That's your sweet spot.
    6. Test Performance: After finding a visually acceptable value, test the performance of your model. If it's too slow, increase the angle slightly until you find a balance between smoothness and speed.
    7. Document-Specific Settings: If you have a particularly complex model, consider using document-specific settings to override the global preference.

    Important Considerations:

    • Rendering vs. UI Display: The "Maximum angular deflection" setting only affects the display in the FreeCAD UI. When you render the model (using the Path Workbench, or exporting to a rendering engine), the rendering engine will have its own settings for surface smoothness. A low deflection angle in FreeCAD doesn't guarantee a smooth render, but it's a good starting point.
    • Boolean Operations: Boolean operations (union, difference, intersection) can sometimes create surfaces with a lot of faceting. You may need to refine the mesh after a boolean operation to improve the smoothness. The Mesh Design workbench can help with this.
    • Part vs. Sketcher: The setting affects Part geometry more directly than Sketcher geometry. Sketcher geometry is typically displayed as lines and curves, which are not affected by the deflection angle.
    • Hardware Acceleration: Make sure your graphics card drivers are up to date and that FreeCAD is using hardware acceleration (check Edit > Preferences > General > OpenGL).

    In summary, start with 7 degrees and adjust based on your model's complexity, your hardware, and your visual preferences. Don't be afraid to experiment!

    To help me give you even more specific advice, could you tell me:

    • What kind of arched surfaces are you working with? (e.g., simple arcs, complex NURBS surfaces, imported STEP files)
    • What are your computer's specifications? (CPU, GPU, RAM)
    • What is the intended use of the model? (visualization, engineering analysis, manufacturing)

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.