I am running an underglow business, I have a main kit which goes from controller to a Y…
- User
I am running an underglow business, I have a main kit which goes from controller to a Y splitter and each side has 100cm, 2m conntector, 180cm, 2m connector and then 80cm
My leds are 12v and 90/led/m, they are rated for 25W
tell me the expected
mA per diode Wattage Amperage expected voltage dropoff, and will I expect yellowing?
My longest underglow kit will be on one side 110cm, 190cm and 160cm rear. Will I have voltage drop off?
also answer these generalized questions to my kit
battery harness, what gauage wire to the controller, what gauge wire to the LED's, what gauge wire between LEDs will be suitable?
- Assistant
Below is a “one–pager” with the most common numbers you (and your customers) usually want to see, followed by the reasoning so you can check / tweak things any time the strip density, length or supply voltage changes.
────────────────────────────────────────
QUICK REFERENCE (for your 12 V RGB strip, 90 LED / m, spec sheet says 25 W / m)
Per LED
• Current ≈ 23 mA
• Power ≈ 0.28 WPer metre
• Power ≈ 25 W
• Current ≈ 2.08 A (25 W ÷ 12 V)Typical segments in your kit
┌─────────┬─────────┬────────┬──────────────┐
│ Segment │ Length │ Current│ Power @12 V │
├─────────┼─────────┼────────┼──────────────┤
│ Front │ 1.00 m │ 2.1 A │ 25 W │
│ Side │ 1.80 m │ 3.8 A │ 45 W │
│ Rear │ 0.80 m │ 1.7 A │ 20 W │
│ Whole side (1 + 1.8 + 0.8 m) │ 3.6 m │ 7.5 A │ 90 W │
│ “Longest” example (1.1 + 1.9 + 1.6 m) │ 4.6 m │ 9.6 A │115 W │
└─────────┴─────────┴────────┴──────────────┘Fuse / supply head-room → 15 A per side or 20 A total is safe.
────────────────────────────────────────
-
mA PER DIODE
25 W per metre ÷ 12 V = 2.08 A/m
90 LED per metre → 2.08 A ÷ 90 ≈ 23 mA per LED
That’s right in the normal 5050-RGB range (≈20 mA / colour). -
WATTAGE & CURRENT FOR YOUR RUNS
Already summarised in the table above.
Rule of thumb you can memorise:
“90 LED / m @ 12 V pulls ~2 A per metre.” -
VOLTAGE DROP & “YELLOWING” (white turns cream/yellow when voltage is low)
Where it happens:
• Copper tracks inside the strip (especially >2 m fed from one end).
• Long feed wires between segments or from battery → controller.Short answer for your layout
➜ You will see a little dimming / colour shift on full-white, but it’s minor if you feed each LED section from the near end of the 2 m jumper.
➜ Worst case (the 190 cm piece) gets ~0.2 V drop inside the strip + up to ~0.3–0.5 V in the 2 m feed if you use thin wire. That still leaves ≈11.3–11.5 V — good enough that most people will not notice unless they park next to a reference strip.If you want absolutely perfect white: inject power at both ends of the longest section or use heavier feed wire (AWG16) for the 2 m jumpers.
- WIRE GAUGE SELECTION
Think of four different “jobs” the copper has to do:
a) Battery → fuse → controller (whole kit current, worst-case 20 A)
• Automotive AWG14 (2 mm²) minimum.
• If the run is short (<1.5 m) AWG16 is electrically fine, but AWG14 is tougher and standard in car looms.
• Put the fuse as close to the battery tap as possible (20 A ATO/ATC blade).b) Controller → first LED on each branch (≈7–10 A)
• 2 m “feed” cables: AWG16 (1.3 mm²) keeps V-drop <0.5 V.
• If you’re forced to use AWG18, keep them short (<1 m) or accept ~0.7 V drop on full white.c) Between LED sections – carries only what’s downstream
• First 2 m jumper (after the 1 m piece) still sees ≈5.4 A → AWG18 ideal.
• Second 2 m jumper (only feeds the 0.8 m rear) ≈1.7 A → AWG20/22 is OK.d) Ground return has to match the positive wire gauge (same current!).
Cheat-sheet table
┌─────────────────────────────────┬────────┐
│ Current (continuous) │ Wire │
├─────────────────────────────────┼────────┤
│ 15–20 A │ AWG14 │
│ 8–10 A │ AWG16 │
│ 3–7 A │ AWG18 │
│ ≤2 A │ AWG20–22│
└─────────────────────────────────┴────────┘-
DO I NEED POWER INJECTION?
• Up to ~2 m fed from one end = typically fine.
• 3–5 m: inject at both ends or at least mid-strip if you care about pure white.
• You already have natural breaks (each LED stick is separate), so you can parallel-feed them instead of daisy-chaining if you ever redesign the harness. -
SHOULD I EXPECT YELLOWING?
Only at:
• Full-white or pastel colours,
• battery voltage already low (<12 V with engine off),
• OR cheap strips with very thin copper.
Animated colour patterns, breathing, chases etc. = you (and customers) probably won’t notice anything.
────────────────────────────────────────
How to double-check in the field
- Multimeter on DC volts.
- All LEDs full-white, measure at battery: you should see ~13.8 V with engine running.
- Measure at far end of longest strip: if still >12.5 V you’re golden. 12.0 V is still acceptable but starts to warm-tint.
Hope that packs all the numbers you need!
Shout if you want a printable cheat sheet or a wiring-colour suggestion. -
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.