Skip to content
TheChatArchiveThe Chat Archive
GPT 5.1· openaiHugging Face Frontier Reasoning Traces

Create a low-power firmware in C for a battery-operated IoT sensor.

  1. User

    Create a low-power firmware in C for a battery-operated IoT sensor.

  2. Assistant

    Creating low-power firmware

    The user wants to create low-power firmware in C for a battery-powered IoT sensor with no specific guidelines yet. I need to assume a generic Cortex-M MCU, considering whether to use FreeRTOS or go with bare metal. A modular approach for the code will help abstract hardware specifics. I'll provide a code skeleton covering main initialization, sleep modes, interrupts, and sensor readings. To ensure low power, I'll suggest disabling unused peripherals and possibly using an event-driven architecture.Developing concise firmware guidance

    I need to be both concise and information-dense while creating a firmware template. Since the user requested to "create" firmware in C, I should provide code rather than just a design outline. It could be helpful to suggest a generic template and encourage adaptation for their specific MCU and stack.

    I'll include a high-level architecture description, ensuring it’s concise, along with example code files like main.c, power.c, sensors.c, and radio.c. For efficiency, I might combine these into a single "firmware.c" file with pseudo-HAL functions and clear comments.Implementing low-power firmware states

    I'll set up the firmware to use distinct states: INIT, SLEEP, MEASURE, and TRANSMIT. The RTC will wake the system every SAMPLE_INTERVAL_SEC.

    I’ll include functions to configure low power, like SystemClock_ConfigLowPower and GPIO_InitLowPower, along with Sensor_Init and Radio_Init for the necessary communication protocols.

    In the main loop, I’ll use pseudocode to manage low-power sleep while responding to RTC or external interrupts. I’ll also clarify using WFI instructions and optimizing for compile-time. Finally, I plan to propose a bare-metal approach with periodic measurements and deep sleep between events.Structuring the firmware response

    I need to ensure that I don’t mention code outside of the analysis; the final answer should focus solely on the actual response. First, I’ll present quick assumptions and an overview. Then I'll provide the C code with comments to explain key sections. While I aim to keep the explanation of low-power techniques short, I’ll include necessary includes like stdint.h, stdbool.h, and possibly <stddef.h>, avoiding libraries. I'll also ensure the code compiles logically, but I won't go for a multi-file structure since the user hasn’t requested it.Structuring low-power firmware code

    I'll structure the firmware code to include necessary includes and a clear configuration section for parameters like sample intervals and battery levels. I'll define global state flags for wake-up events and prototype necessary hardware abstraction functions.

    In the main function, I'll set up the low-power configurations, enter deep sleep, and manage sensor readings and transmissions. For example, I’ll add functions for power management and a stub for the sensor reading function, while labeling hardware-specific items with TODOs. I’ll keep explanations concise and maintain a reasonable code length, avoiding excessive minimalism or verbosity. Additionally, I'll mention using a tickless RTC instead of SysTick and how to customize HAL functions generically. Below is a self-contained C firmware template for a very low-power, battery-operated IoT sensor node.

    It’s written in portable C and uses a simple event-driven main loop with deep sleep between events. All MCU/sensor/radio specifics are abstracted into “HAL-like” functions you can implement using your vendor’s SDK (STM32 HAL, nRF SDK, MSP, etc.).


    1. Design Overview (brief)

    Behavior:

    • Wake up periodically (e.g., every 5 minutes) via RTC/low-power timer.
    • Power up the sensor(s), take a reading.
    • Optionally send data via radio (BLE, LoRa, sub-GHz, etc.).
    • Power down sensors and radio.
    • Re-enter deep sleep (STOP/STANDBY/ULP mode).
    • Optionally wake from external events (button, motion, etc.).

    Low-power techniques used in template:

    • Deep sleep between measurements (using __WFI() conceptually).
    • RTC-based wakeup, no high-frequency SysTick running.
    • Sensors and radio powered only when needed.
    • All unused GPIO set to low-power state.
    • ISR does minimal work, sets flags for main loop.

    You only need to implement the hardware-specific “HAL” functions for your MCU and peripherals.


    2. Firmware Template: main.c

    /*
     * Low-power IoT Sensor Node Firmware (Template)
     *
     * Assumptions:
     *   - Generic Cortex-M-like MCU (but logic applies to many MCUs).
     *   - RTC or low-power timer can wake from deep sleep.
     *   - One “main” sensor and one radio interface.
     *   - Vendor-specific HAL functions must be provided by you.
     */
    
    #include <stdint.h>
    #include <stdbool.h>
    #include <string.h>
    
    /*================= User Configuration =================*/
    
    #define SAMPLE_INTERVAL_SECONDS     300U   /* 5 minutes */
    #define SENSOR_POWER_STABILIZE_MS   10U
    #define BATTERY_LOW_MV              2500U  /* 2.5V low-battery threshold */
    
    #define PAYLOAD_MAX_LEN             32U
    
    /* Optional: send only every Nth sample to save power */
    #define SEND_EVERY_N_SAMPLES        1U     /* 1 = send every sample */
    
    /*================= Global State / Flags =================*/
    
    typedef struct {
        int16_t temperature_c_x100;  /* e.g., 2351 = 23.51 °C */
        int16_t humidity_rh_x100;    /* e.g., 4567 = 45.67 %RH */
        uint16_t battery_mv;         /* battery voltage in mV */
        uint32_t seq_no;             /* sequence counter */
    } sensor_sample_t;
    
    volatile bool g_rtc_wakeup     = false;
    volatile bool g_ext_event      = false;
    volatile bool g_radio_done     = false;
    
    static uint32_t g_sample_count = 0;
    
    /*================= Hardware Abstraction Prototypes =================
     * Implement these using your MCU vendor's libraries.
     */
    
    /* System & Clock */
    static void SystemClock_Config_LowPower(void);
    static void Peripherals_Init_LowPower(void);
    static void GPIO_Init_LowPower(void);
    
    /* RTC / Low-Power Timer */
    static void RTC_Init_And_Start(uint32_t interval_seconds);
    static void RTC_Clear_Wakeup_Flag(void);
    
    /* Sleep / Power Modes */
    static void Enter_DeepSleep(void);
    
    /* Time helpers */
    static void Delay_ms(uint32_t ms);
    
    /* Sensor interface */
    static void Sensor_HW_Init(void);
    static void Sensor_PowerOn(void);
    static void Sensor_PowerOff(void);
    static bool Sensor_Read(sensor_sample_t *out_sample);
    
    /* Battery measurement */
    static uint16_t Battery_Read_mV(void);
    
    /* Radio interface */
    static void Radio_HW_Init(void);
    static void Radio_PowerOn(void);
    static void Radio_PowerOff(void);
    static void Radio_SendAsync(const uint8_t *data, uint16_t len);
    
    /* Encoding */
    static uint16_t Encode_Payload(const sensor_sample_t *sample,
                                   uint8_t *out_buf,
                                   uint16_t out_buf_len);
    
    /*================= Main Application Logic =================*/
    
    static void app_init(void)
    {
        SystemClock_Config_LowPower();
        GPIO_Init_LowPower();
        Peripherals_Init_LowPower();
    
        Sensor_HW_Init();
        Radio_HW_Init();
    
        RTC_Init_And_Start(SAMPLE_INTERVAL_SECONDS);
    
        /* Ensure sensors & radio are off at boot */
        Sensor_PowerOff();
        Radio_PowerOff();
    }
    
    static void app_handle_rtc_wakeup(void)
    {
        sensor_sample_t sample;
        memset(&sample, 0, sizeof(sample));
    
        g_sample_count++;
    
        /* Read battery first (often ADC with reference that may
           already be active from RTC/LPTIM implementations). */
        sample.battery_mv = Battery_Read_mV();
        sample.seq_no     = g_sample_count;
    
        /* Optional: adaptive behavior if battery low */
        if (sample.battery_mv < BATTERY_LOW_MV) {
            /* Example policy:
             * - Increase interval, or
             * - Skip radio transmission, or
             * - Enter ultra-deep sleep after sending low-bat alarm once.
             * Keep it simple here: we still measure + send.
             */
        }
    
        /* Power sensor only for the measurement window */
        Sensor_PowerOn();
        Delay_ms(SENSOR_POWER_STABILIZE_MS);  /* short wait for sensor to stabilize */
        if (!Sensor_Read(&sample)) {
            /* On failure, you may log or encode an error field.
             * For simplicity, just mark as sentinel value.
             */
            sample.temperature_c_x100 = -32768; /* error code */
            sample.humidity_rh_x100   = -32768; /* error code */
        }
        Sensor_PowerOff();
    
        /* Decide whether we send or keep silent */
        if (SEND_EVERY_N_SAMPLES == 0 ||
            (g_sample_count % SEND_EVERY_N_SAMPLES) != 0) {
            /* Not time to send yet; just return to sleep */
            return;
        }
    
        /* Prepare payload */
        uint8_t payload[PAYLOAD_MAX_LEN];
        uint16_t len = Encode_Payload(&sample, payload, sizeof(payload));
    
        /* Send over radio; power it only for TX window */
        Radio_PowerOn();
        g_radio_done = false;
        Radio_SendAsync(payload, len);
    
        /* Wait for radio completion or timeout; keep CPU mostly asleep */
        uint32_t timeout_ms = 2000U; /* adjust to your radio airtime */
        while (!g_radio_done && timeout_ms > 0) {
            /* In many MCUs, you can re-enter light sleep here and wake
               on radio IRQ. If you cannot, a short Delay_ms is OK. */
            Enter_DeepSleep();  /* wakes up from radio IRQ or RTC etc. */
            /* If you prefer polling, you can call Delay_ms(10) instead. */
            /* timeout_ms -= 10;  (if using Delay_ms) */
            /* For simplicity, assume radio_done will occur quickly. */
            break;
        }
        Radio_PowerOff();
    }
    
    static void app_handle_ext_event(void)
    {
        /* Example: a button, motion, or other sensor-triggered event.
         * Keep this very small or just set a higher-priority flag.
         * For now, we do nothing special.
         */
    }
    
    /*================= main() =================*/
    
    int main(void)
    {
        app_init();
    
        for (;;) {
            /* Main event loop: let interrupts set flags, and we react here.
             * Between events, always enter deepest sleep possible.
             */
            Enter_DeepSleep();
    
            if (g_rtc_wakeup) {
                g_rtc_wakeup = false;
                RTC_Clear_Wakeup_Flag();
                app_handle_rtc_wakeup();
            }
    
            if (g_ext_event) {
                g_ext_event = false;
                app_handle_ext_event();
            }
    
            /* Other event flags (e.g., radio TX done) are handled
             * implicitly, not polled here, to keep code simple.
             */
        }
    }
    
    /*================= Interrupt Handlers (Skeletons) =================
     * Wire these to your real vector table / startup code.
     */
    
    /* RTC / Low-power timer wakeup ISR */
    void RTC_WKUP_IRQHandler(void)
    {
        /* Clear hardware interrupt flag (MCU-specific) */
        /* Example (STM32-style): __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(&hrtc, RTC_FLAG_WUTF); */
        /* ... your code ... */
    
        g_rtc_wakeup = true;
    }
    
    /* External event ISR (e.g., GPIO, motion, button) */
    void EXTIx_IRQHandler(void)
    {
        /* Clear EXTI flag (MCU-specific) */
        /* ... your code ... */
    
        g_ext_event = true;
    }
    
    /* Radio interrupt (TX done, RX done, etc.) */
    void RADIO_IRQHandler(void)
    {
        /* Check radio status and clear IRQs (radio-specific) */
        /* If TX completed: */
        g_radio_done = true;
    }
    
    /*================= Hardware Abstraction: Stubs =================
     * Everything below must be implemented for your specific MCU / board.
     * They are written as stubs or pseudo-code.
     */
    
    /*---------- System / Clock / GPIO ----------*/
    
    /* Configure system clock for low-power:
     * - Use low-frequency oscillator (e.g., MSI/LSI/LSE).
     * - Disable unnecessary PLLs and high-speed clocks.
     * - Reduce core frequency as much as acceptable.
     */
    static void SystemClock_Config_LowPower(void)
    {
        /* TODO: MCU-specific clock configuration.
         *
         * Example ideas:
         *   - Switch system clock to 4 MHz internal RC.
         *   - Disable PLL, external crystal if not needed.
         *   - Set flash wait-states appropriately.
         */
    }
    
    /* Init basic peripherals needed in low-power mode:
     * - RTC / LPTIM
     * - ADC (for battery)
     * - I2C/SPI for sensors
     * - Radio SPI/UART
     */
    static void Peripherals_Init_LowPower(void)
    {
        /* TODO: enable clocks for needed peripherals only. */
    }
    
    /* Configure all GPIO to low-leakage state:
     * - Unused pins: analog input, no pull.
     * - Used pins: correct direction, no unnecessary pull-ups.
     */
    static void GPIO_Init_LowPower(void)
    {
        /* TODO: MCU-specific GPIO config. */
    }
    
    /*---------- RTC / Low-Power Timer ----------*/
    
    static void RTC_Init_And_Start(uint32_t interval_seconds)
    {
        /* TODO: Configure RTC or low-power timer to generate
         * a wake-up interrupt every interval_seconds.
         *
         * Example (conceptual):
         *   - Configure LSE/LSI as RTC clock.
         *   - Set wakeup timer to interval_seconds.
         *   - Enable interrupt.
         */
        (void)interval_seconds;
    }
    
    static void RTC_Clear_Wakeup_Flag(void)
    {
        /* TODO: Clear hardware RTC wakeup flag. */
    }
    
    /*---------- Sleep / Power Modes ----------*/
    
    /* Enter deepest sleep mode that:
     * - Retains RTC and wakeup sources.
     * - Keeps RAM content if needed.
     */
    static void Enter_DeepSleep(void)
    {
        /* TODO: Use vendor API to enter STOP/STANDBY/ULP.
         * For ARM Cortex-M, minimal example:
         *
         *   SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
         *   __WFI();
         *
         * For ST HAL:
         *   HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI);
         */
        __asm volatile ("wfi");
    }
    
    /*---------- Time Helpers ----------*/
    
    /* Simple millisecond delay.
     * Prefer a low-power timer or RTC; avoid busy-waiting if possible.
     */
    static void Delay_ms(uint32_t ms)
    {
        /* TODO: Implement using:
         *   - A general-purpose timer, or
         *   - RTC tick, or
         *   - If absolutely necessary, a calibrated busy loop.
         */
        (void)ms;
    }
    
    /*---------- Sensor HAL ----------*/
    
    static void Sensor_HW_Init(void)
    {
        /* TODO: Configure I2C/SPI, GPIO pins, etc., for the sensor.
         * Don't power it up here; just ready the interface.
         */
    }
    
    /* Control sensor power rail (via MOSFET / GPIO) */
    static void Sensor_PowerOn(void)
    {
        /* TODO: Set GPIO high to enable sensor power regulator. */
    }
    
    static void Sensor_PowerOff(void)
    {
        /* TODO: Set GPIO low to disable sensor power. */
    }
    
    /* Read sensor data.
     * Return true on success, false on failure/time-out.
     */
    static bool Sensor_Read(sensor_sample_t *out_sample)
    {
        /* TODO: Replace with real sensor code.
         * Example for a temperature/humidity sensor:
         *   - Trigger measurement (I2C/SPI).
         *   - Wait for completion (or poll status).
         *   - Read raw values.
         *   - Convert to °C x100 and %RH x100.
         */
    
        /* Dummy test implementation */
        out_sample->temperature_c_x100 = 2300; /* 23.00°C */
        out_sample->humidity_rh_x100   = 5000; /* 50.00%RH */
        return true;
    }
    
    /*---------- Battery Measurement ----------*/
    
    static uint16_t Battery_Read_mV(void)
    {
        /* TODO: Implement ADC-based battery measurement:
         *   - Configure ADC channel to Vbat or voltage divider input.
         *   - Take one or more samples.
         *   - Convert to mV based on reference voltage.
         */
    
        /* Dummy fixed value */
        return 3000;  /* 3.0V */
    }
    
    /*---------- Radio HAL ----------*/
    
    static void Radio_HW_Init(void)
    {
        /* TODO: Init SPI/UART, radio reset pin, IRQ pin, etc. */
    }
    
    static void Radio_PowerOn(void)
    {
        /* TODO: Enable radio regulator / set power pin. */
    }
    
    static void Radio_PowerOff(void)
    {
        /* TODO: Disable radio regulator / set power pin low. */
    }
    
    /* Transmit payload asynchronously.
     * Completion is signaled via RADIO_IRQHandler -> g_radio_done.
     */
    static void Radio_SendAsync(const uint8_t *data, uint16_t len)
    {
        /* TODO: Implement using your radio driver.
         * Example:
         *   - Load data into radio TX FIFO.
         *   - Start TX.
         *   - Return immediately; ISR will set g_radio_done.
         */
        (void)data;
        (void)len;
    }
    
    /*---------- Payload Encoding ----------*/
    
    /* Simple binary payload:
     * [0..1]  temperature (int16_t, °C x100, little-endian)
     * [2..3]  humidity    (int16_t, %RH x100, little-endian)
     * [4..5]  battery_mV  (uint16_t, little-endian)
     * [6..9]  seq_no      (uint32_t, little-endian)
     */
    static uint16_t Encode_Payload(const sensor_sample_t *s,
                                   uint8_t *out_buf,
                                   uint16_t out_buf_len)
    {
        if (out_buf_len < 10U) {
            return 0;
        }
    
        out_buf[0] = (uint8_t)(s->temperature_c_x100 & 0xFF);
        out_buf[1] = (uint8_t)((s->temperature_c_x100 >> 8) & 0xFF);
    
        out_buf[2] = (uint8_t)(s->humidity_rh_x100 & 0xFF);
        out_buf[3] = (uint8_t)((s->humidity_rh_x100 >> 8) & 0xFF);
    
        out_buf[4] = (uint8_t)(s->battery_mv & 0xFF);
        out_buf[5] = (uint8_t)((s->battery_mv >> 8) & 0xFF);
    
        out_buf[6] = (uint8_t)(s->seq_no & 0xFF);
        out_buf[7] = (uint8_t)((s->seq_no >> 8) & 0xFF);
        out_buf[8] = (uint8_t)((s->seq_no >> 16) & 0xFF);
        out_buf[9] = (uint8_t)((s->seq_no >> 24) & 0xFF);
    
        return 10U;
    }
    

    3. How to Adapt This to Your Board

    To make this run on real hardware:

    1. Choose MCU & SDK
      Example: STM32L0/L4 (STM32Cube), nRF52 (nRF5 SDK / nRF Connect), MSP430, etc.

    2. Implement HAL functions

      • Map SystemClock_Config_LowPower, RTC_Init_And_Start, Enter_DeepSleep, etc., to your SDK calls.
      • Implement Sensor_* using your sensor’s I2C/SPI driver.
      • Implement Radio_* using your LoRa/BLE/Wi-Fi module’s driver.
    3. Set interrupt vectors

      • Point RTC, EXTI, and radio IRQ in your vector table to the three ISRs shown.
    4. Compile with size & power optimizations

      • Use -Os or -O2, enable LTO, remove unused code.
      • Disable debug interfaces (SWD/JTAG) in production if they leak power.

    If you tell me your exact MCU (e.g., STM32L072, nRF52832, etc.) and sensor/radio parts, I can rewrite the HAL stubs above into concrete code using that vendor’s libraries.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.