ISSUE DESCRIPTION fix(installer): back navigation from Pi-only install shows unrelated…
- User
ISSUE DESCRIPTION
fix(installer): back navigation from Pi-only install shows unrelated Gentle AI configuration
Pre-flight Checklist
- I have searched existing issues and this is not a duplicate
- I understand that PRs will be rejected if the linked issue does not have
status:approved
📝 Bug Description
When running the
gentle-piinstaller fromgentle-ai, if I select onlyPias the installation target and then useBackon the next step,
the installer returns to an unexpected configuration flow.Instead of going back to the previous installation target selection, it shows configuration options that do not correspond to the selected
Pi-only path, such as TDD configuration, multi-agent installation, communication style, and related Gentle AI setup options.🔄 Steps to Reproduce
- Start the
gentle-aiinstaller.
2. Select onlyPias the installation target.
3. Continue to the next step.
4. SelectBack.
5. Observe that the installer shows configuration screens for TDD, multi-agent setup, speaking style, etc.
✅ Expected Behavior
After selecting
Back, the installer should return to the previous relevant step in the Pi-only installation flow, likely the installation
target selection screen.❌ Actual Behavior
The installer jumps to unrelated Gentle AI configuration screens, including TDD setup, multi-agent installation, communication style, and other
options that were not expected after choosing a Pi-only installation.Gentle AI Version
v 1.30.5
Operating System
macOS
AI Agent / Client
Other
📋 Affected Area
CLI (commands, flags)
💡 Logs / Error Output
No logs available. This appears to be an installer navigation/state-flow issue.Additional Context
This happens specifically when selecting only
Piduring installation and then navigating back from the following step.Interface
No new interfaces are introduced.
ADDITIONAL ADVICE
Since you are given a git repository, you can use git commands to simplify your work. For example, if you made a mistake and want to revert your changes, you can use
git checkout <file>to restore the file to its original state. You can also reset all changes in the repository usinggit reset --hardcommand. Additionally, you can usegit stashandgit stash popto temporarily save your changes and restore them later. Finally, you can see the changes that you've made (which will be submitted when you callsubmit) usinggit statusorgit diffcommands. However you don't need to usegit addorgit commitbefore submitting your changes. In fact,submitonly submits currently unstaged changes because it usesgit diffto get the changes that need to be submitted.CHECKLIST
Before submitting your solution, please go over the following checklist and make sure you've done everything:
- If an error was reported in the issue description, I have successfully reproduced it.
- If an error was reported in the issue description, I have confirmed that my fix resolves the error.
- I have thought about edge cases and made sure my fix handles them as well.
- I have run existing tests in the repository that might have been affected by the change I made and confirmed that they pass. I want you to list every bullet from this checklist and write your reasoning for why you think you did it or didn't need to.
Repository has been uploaded and your shell is currently at the repository root. Time to solve the issue!
(Current directory: /gentle-ai, current file: none) bash-$
Assistant
Let me write a temporary reproduction test:
Assistant
Bug reproduced (goes to ScreenPreset=5). Now fix both back paths:
Assistant
Add preset normalization to handle that edge case:
Assistant
There's a stray duplicate
}at line 1500:Assistant
All tests pass. Let me verify the edge case too with an extended temp test:
Assistant
The hang pre-exists on the pristine tree (no TTY in this environment) — unrelated to my change. Run remaining packages:
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.
Identical first prompt
claude-sonnet-5Compare side by side →
claude-sonnet-5Compare side by side →
claude-sonnet-5Compare side by side →
claude-sonnet-5Compare side by side →
claude-sonnet-5Compare side by side →
Qwen/Qwen3.6-35B-A3BCompare side by side →
Qwen/Qwen3.6-35B-A3BCompare side by side →
Qwen/Qwen3.6-35B-A3BCompare side by side →
Qwen/Qwen3.6-35B-A3BCompare side by side →
Qwen/Qwen3.6-35B-A3BCompare side by side →
Qwen/Qwen3.6-27BCompare side by side →
Qwen/Qwen3.5-35B-A3BCompare side by side →