Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0613· openaiHugging Face Suzhen/CodeChat

how to transmit serial data to pixlhawk 6c outopilot with uart1 stm32F407VET…

  1. User

    how to transmit serial data to pixlhawk 6c outopilot with uart1 stm32F407VET microcontroller insted of RC

  2. Assistant

    To transmit serial data to the Pixhawk 6C autopilot using UART1 on the STM32F407VET microcontroller instead of RC, you can follow these steps:

    1. Configure the UART1 peripheral on the STM32F407VET microcontroller:

      • Enable the USART1 peripheral clock in the RCC register.
      • Configure the GPIO pins for UART1 transmission and reception.
      • Configure the UART1 settings such as baud rate, data bits, stop bits, and parity.
    2. Initialize the UART1 peripheral:

      • Initialize the UART1 peripheral with the configured settings.
      • Enable the transmission and reception processes of UART1.
    3. Prepare the serial data to be transmitted:

      • Format the serial data according to the protocol supported by the Pixhawk 6C autopilot.
    4. Send the serial data:

      • Use the UART1 transmit data register (DR) to send the serial data byte by byte.
      • Wait for the transmission to complete before sending the next byte.

    Here is a code example using the STM32Cube HAL library:

    #include "stm32f4xx_hal.h"
    
    UART_HandleTypeDef huart1;
    
    void UART1_Init(void)
    {
      huart1.Instance = USART1;
      huart1.Init.BaudRate = 115200;
      huart1.Init.WordLength = UART_WORDLENGTH_8B;
      huart1.Init.StopBits = UART_STOPBITS_1;
      huart1.Init.Parity = UART_PARITY_NONE;
      huart1.Init.Mode = UART_MODE_TX_RX;
      huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
      huart1.Init.OverSampling = UART_OVERSAMPLING_16;
    
      // Configure GPIO pins for USART1
      GPIO_InitTypeDef GPIO_InitStruct;
      __HAL_RCC_GPIOB_CLK_ENABLE();
      GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
      GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
      GPIO_InitStruct.Pull = GPIO_PULLUP;
      GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
      GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
      HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
    
      // Enable USART1 peripheral clock
      __HAL_RCC_USART1_CLK_ENABLE();
    
      // Initialize USART1
      HAL_UART_Init(&huart1);
    }
    
    void UART1_SendData(uint8_t* data, uint16_t size)
    {
      HAL_UART_Transmit(&huart1, data, size, HAL_MAX_DELAY);
    }
    
    int main(void)
    {
      // Initialize the UART1 peripheral
      UART1_Init();
    
      // Prepare the serial data to be transmitted
      uint8_t serialData[] = {0x01, 0x02, 0x03, 0x04};
    
      // Send the serial data
      UART1_SendData(serialData, sizeof(serialData));
    
      while (1)
      {
        // Your main code here
      }
    }
    

    This code configures UART1 on the STM32F407VET microcontroller and sends the serialData array. You can modify the baud rate, data format, and other settings to match the requirements of the Pixhawk 6C autopilot.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.