Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0613· openaiHugging Face Suzhen/CodeChat

make me an esp32 arduino sketch that uses an esp32 hardware interupt to see if i2c data…

  1. Assistant

    My name is OpenAI Assistant. I'm an AI trained to help with a variety of tasks and answer questions. How can I assist you today?

  2. User

    make me an esp32 arduino sketch that uses an esp32 hardware interupt to see if i2c data is beying send towards the esp32 and runs a routine to capture the i2c data into a i2cdata queue, then serial prinln the i2cdata queue for debugging message that i2c data has been send and then returns to the normal loop.

  3. Assistant

    Sure, here's an example ESP32 Arduino sketch that uses hardware interrupts to capture I2C data and print it through the serial monitor:

    #include <Wire.h>
    
    // I2C slave address
    #define SLAVE_ADDR 0x12
    
    // Buffer size to store I2C data
    #define BUFFER_SIZE 32
    
    // Queue to store I2C data
    QueueHandle_t i2cDataQueue;
    
    // Interrupt flag
    volatile bool i2cInterruptFlag = false;
    
    void IRAM_ATTR i2cInterrupt() {
      i2cInterruptFlag = true;
    }
    
    void setup() {
      Serial.begin(115200);
      Wire.begin(SLAVE_ADDR);
    
      // Set up the interrupt for I2C
      attachInterrupt(digitalPinToInterrupt(21), i2cInterrupt, FALLING);
    
      // Initialize the I2C data queue
      i2cDataQueue = xQueueCreate(BUFFER_SIZE, sizeof(uint8_t));
    
      Serial.println("I2C Interrupt Example");
    }
    
    void loop() {
      if (i2cInterruptFlag) {
        // Clear the interrupt flag
        i2cInterruptFlag = false;
    
        // Read I2C data
        while (Wire.available()) {
          uint8_t data = Wire.read();
    
          // Enqueue the I2C data
          if (xQueueSendToBack(i2cDataQueue, &data, 0) != pdTRUE) {
            Serial.println("I2C Data Queue is full!");
          }
        }
    
        // Print the I2C data queue for debugging
        Serial.print("I2C Data: ");
        while (!xQueueIsEmpty(i2cDataQueue)) {
          uint8_t data;
          xQueueReceive(i2cDataQueue, &data, 0);
          Serial.print(data);
          Serial.print(" ");
        }
        Serial.println();
      }
    
      // Perform other tasks in the main loop
      // ...
    }
    

    This sketch sets up an interrupt on GPIO pin 21 for the I2C signals. When an interrupt occurs, the sketch reads the data from the I2C bus and adds it to a queue. Then, it prints the contents of the queue for debugging purposes and continues with the main loop.

    Please note that this code assumes you have the necessary Wire library installed and your I2C device is properly connected to the ESP32. Adjust the SLAVE_ADDR according to your I2C device's address.

  4. User

    Compilation error: 'xQueueIsEmpty' was not declared in this scope note: suggested alternative: 'xQueueCreate'

  5. Assistant

    I apologize for the error. It seems that the xQueueIsEmpty function is not available in the standard Arduino library. You can use the uxQueueMessagesWaiting function as an alternative to check if the queue is empty. Here's the modified code:

    #include <Wire.h>
    
    // I2C slave address
    #define SLAVE_ADDR 0x12
    
    // Buffer size to store I2C data
    #define BUFFER_SIZE 32
    
    // Queue to store I2C data
    QueueHandle_t i2cDataQueue;
    
    // Interrupt flag
    volatile bool i2cInterruptFlag = false;
    
    void IRAM_ATTR i2cInterrupt() {
      i2cInterruptFlag = true;
    }
    
    void setup() {
      Serial.begin(115200);
      Wire.begin(SLAVE_ADDR);
    
      // Set up the interrupt for I2C
      attachInterrupt(digitalPinToInterrupt(21), i2cInterrupt, FALLING);
    
      // Initialize the I2C data queue
      i2cDataQueue = xQueueCreate(BUFFER_SIZE, sizeof(uint8_t));
    
      Serial.println("I2C Interrupt Example");
    }
    
    void loop() {
      if (i2cInterruptFlag) {
        // Clear the interrupt flag
        i2cInterruptFlag = false;
    
        // Read I2C data
        while (Wire.available()) {
          uint8_t data = Wire.read();
    
          // Enqueue the I2C data
          if (xQueueSendToBack(i2cDataQueue, &data, 0) != pdTRUE) {
            Serial.println("I2C Data Queue is full!");
          }
        }
    
        // Print the I2C data queue for debugging
        Serial.print("I2C Data: ");
        if (uxQueueMessagesWaiting(i2cDataQueue) == 0) {
          Serial.println("Empty");
        } else {
          while (uxQueueMessagesWaiting(i2cDataQueue)) {
            uint8_t data;
            xQueueReceive(i2cDataQueue, &data, 0);
            Serial.print(data);
            Serial.print(" ");
          }
          Serial.println();
        }
      }
    
      // Perform other tasks in the main loop
      // ...
    }
    

    In the modified code, the uxQueueMessagesWaiting function is used to check if the I2C data queue is empty or not. If the queue is empty, it prints "Empty"; otherwise, it reads and prints the data from the queue.

    Again, make sure you have the necessary Wire library installed and your I2C device is properly connected to the ESP32. Adjust the SLAVE_ADDR according to your I2C device's address.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.