Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0301· openaiHugging Face Suzhen/CodeChat

请用Keil…

  1. User

    请用Keil uVision5编写一段程序,程序要求实现:按下K1键,直流电机从停止状态开始缓慢加速,加速5秒后匀速运动10秒,再减速5秒后停止,整个过程只需完成1次,按下K1键,直流电机加速转动;按下K2键,直流电机减速转动;硬件连接方式为M-STM32F103VE的PB0、PA8、PB1分别接直流电机控制接口的EN1、IN1、IN2;M-STM32F103VE的PC0、PC1分别接M-KEY的K1、K2。

  2. Assistant

    由于没有实际的硬件设备,以下代码仅供参考:

    #include "stm32f10x.h"
    
    #define EN1 GPIO_Pin_0
    #define IN1 GPIO_Pin_8
    #define IN2 GPIO_Pin_1
    #define K1 GPIO_Pin_0
    #define K2 GPIO_Pin_1
    
    void GPIO_Configuration(void)
    {
        GPIO_InitTypeDef GPIO_InitStructure;
        
        /* Enable GPIOB, GPIOC clock */
        RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC, ENABLE);
    
        /* Configure PB0, PB1, PA8 as output for controlling the motor */
        GPIO_InitStructure.GPIO_Pin = EN1 | IN1 | IN2;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
        GPIO_Init(GPIOB, &GPIO_InitStructure);
    
        /* Configure PC0, PC1 as input for K1 and K2 buttons */
        GPIO_InitStructure.GPIO_Pin = K1 | K2;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD;  // Note: IPD means input pull-down
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
        GPIO_Init(GPIOC, &GPIO_InitStructure);
    
        /* Set PB0 to high level to stop the motor initially */
        GPIO_SetBits(GPIOB, EN1);
    }
    
    void delay_ms(uint16_t ms)
    {
        volatile uint32_t nCount;
        RCC_ClocksTypeDef RCC_Clocks;
        RCC_GetClocksFreq(&RCC_Clocks);
        nCount = (RCC_Clocks.HCLK_Frequency / 10000) * ms;
        for (; nCount != 0; nCount--);
    }
    
    void motor_slowly_accelerate(void)
    {
        uint16_t duty_cycle = 0;
        while(duty_cycle < 900)
        {
            GPIO_SetBits(GPIOB, EN1);
            GPIO_SetBits(GPIOB, IN1);
            GPIO_ResetBits(GPIOB, IN2);
            delay_ms(50);
            duty_cycle += 100;
        }
    }
    
    void motor_const_speed(void)
    {
        uint16_t i = 0;
        while(i < 20)
        {
            GPIO_SetBits(GPIOB, EN1);
            GPIO_SetBits(GPIOB, IN1);
            GPIO_ResetBits(GPIOB, IN2);
            delay_ms(1000);
            i++;
        }
    }
    
    void motor_slowly_decelerate(void)
    {
        uint16_t duty_cycle = 1000;
        while(duty_cycle > 100)
        {
            GPIO_SetBits(GPIOB, EN1);
            GPIO_SetBits(GPIOB, IN1);
            GPIO_ResetBits(GPIOB, IN2);
            delay_ms(50);
            duty_cycle -= 100;
        }
    }
    
    int main(void)
    {
        GPIO_Configuration();
    
        while (1)
        {
            // Wait for K1 button to be pressed
            while(GPIO_ReadInputDataBit(GPIOC, K1) == 1);
            delay_ms(20); // debounce
            while(GPIO_ReadInputDataBit(GPIOC, K1) == 0);
            delay_ms(20); // debounce
    
            // Start the motor
            motor_slowly_accelerate();
            motor_const_speed();
            motor_slowly_decelerate();
    
            // Wait for K1 button to be released
            while(GPIO_ReadInputDataBit(GPIOC, K1) == 0);
            delay_ms(20); // debounce
    
            // Wait for K2 button to be pressed
            while(GPIO_ReadInputDataBit(GPIOC, K2) == 1);
            delay_ms(20); // debounce
            while(GPIO_ReadInputDataBit(GPIOC, K2) == 0);
            delay_ms(20); // debounce
    
            // Stop the motor
            GPIO_SetBits(GPIOB, EN1);
        }
    }
    

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.