stm32f103c8t6 tcp/ip协议 代码
- User
stm32f103c8t6 tcp/ip协议 代码
- Assistant
以下是一个使用STM32F103C8T6的TCP/IP协议代码示例:
#include "stm32f10x.h" #include "lwip/tcpip.h" #include "lwip/netif.h" #include "lwip/dhcp.h" #include "lwip/ip_addr.h" #include "lwip/init.h" #include "lwip/tcp.h" #include "lwip/udp.h" #include "lwip/sys.h" // 硬件初始化 static void hw_init(void) { // Init RCC and GPIO here //... } // 连接回调函数 static err_t connect_callback(void *arg, struct tcp_pcb *tpcb, err_t err) { // 连接成功回调函数 //... } // 接收数据回调函数 static err_t recv_callback(void *arg, struct tcp_pcb *tpcb, struct pbuf *p, err_t err) { // 接收数据回调函数 //... tcp_recved(tpcb, p->tot_len); pbuf_free(p); return ERR_OK; } // 发送数据回调函数(当数据发送完毕后会调用) static err_t sent_callback(void *arg, struct tcp_pcb *tpcb, u16_t len) { // 数据发送完毕回调函数 //... return ERR_OK; } // 断开连接回调函数 static void close_callback(void *arg, struct tcp_pcb *tpcb, err_t err) { // 断开连接回调函数 //... tcp_arg(tpcb, NULL); tcp_sent(tpcb, NULL); tcp_recv(tpcb, NULL); tcp_close(tpcb); } // 初始化TCP服务器 void tcp_server_init(void) { struct tcp_pcb *pcb; err_t err; pcb = tcp_new(); if (pcb != NULL) { err = tcp_bind(pcb, IP_ADDR_ANY, 10000); if (err == ERR_OK) { pcb = tcp_listen(pcb); tcp_accept(pcb, connect_callback); } else { // 绑定失败处理 //... } } else { // 分配失败处理 //... } } int main(void) { hw_init(); tcpip_init(NULL, NULL); tcp_server_init(); while (1) { tcpip_poll(NULL); } return 0; }以上示例使用lwIP库的TCP/IP协议栈来实现一个简单的TCP服务器。首先在
hw_init()函数中进行硬件初始化,然后在tcp_server_init()函数中初始化TCP服务器。创建一个TCP PCB(协议控制块),然后绑定到指定的IP地址和端口上,最后开始监听连接请求。回调函数connect_callback()用于处理连接成功后的操作,recv_callback()处理接收到的数据,sent_callback()处理已发送完成的数据,close_callback()处理断开连接事件。在
main()中首先进行硬件初始化,然后调用tcpip_init()进行lwIP初始化,最后调用tcp_server_init()初始化TCP服务器。最后进入无限循环,在循环中调用tcpip_poll()函数来处理lwIP的定时任务。需要注意的是,以上代码仅仅是一个示例,具体的应用场景和需求会有所不同,你可以根据自己的实际需求进行修改和扩展。同时,你还需要在工程中添加lwIP库的相关文件,并进行相应的配置和编译设置。
- User
stm32f103c8t芯片与W5500芯片的SPI通信代码
- Assistant
以下是一个基于STM32F103C8T6芯片和W5500芯片之间实现SPI通信的代码示例:
#include "stm32f10x.h" #include "stm32f10x_spi.h" #include "stm32f10x_gpio.h" /* 定义SPIx和片选引脚 */ #define SPIx SPI1 #define SPIx_CLK RCC_APB2Periph_SPI1 #define SPIx_GPIO GPIOA #define SPIx_GPIO_CLK RCC_APB2Periph_GPIOA #define SPIx_PIN_SCK GPIO_Pin_5 #define SPIx_PIN_MISO GPIO_Pin_6 #define SPIx_PIN_MOSI GPIO_Pin_7 #define W5500_CS_PORT GPIOB #define W5500_CS_PIN GPIO_Pin_12 // 初始化SPI static void SPIx_Init(void) { SPI_InitTypeDef SPI_InitStructure; GPIO_InitTypeDef GPIO_InitStructure; /* Enable SPIx_GPIO and SPIx clocks */ RCC_APB2PeriphClockCmd(SPIx_GPIO_CLK | SPIx_CLK, ENABLE); /* Configure SPIx pins: SCK, MISO and MOSI */ GPIO_InitStructure.GPIO_Pin = SPIx_PIN_SCK | SPIx_PIN_MISO | SPIx_PIN_MOSI; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; GPIO_Init(SPIx_GPIO, &GPIO_InitStructure); /* Chip select pin */ GPIO_InitStructure.GPIO_Pin = W5500_CS_PIN; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(W5500_CS_PORT, &GPIO_InitStructure); /* Enable SPIx */ SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex; SPI_InitStructure.SPI_Mode = SPI_Mode_Master; SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; SPI_InitStructure.SPI_CPOL = SPI_CPOL_High; SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; SPI_InitStructure.SPI_NSS = SPI_NSS_Soft; SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4; SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; SPI_Init(SPIx, &SPI_InitStructure); /* Enable SPIx */ SPI_Cmd(SPIx, ENABLE); } // 写入一个字节数据到W5500 void W5500_WriteByte(uint8_t data) { /* Chip select, active low */ GPIO_ResetBits(W5500_CS_PORT, W5500_CS_PIN); /* Send byte through the SPIx peripheral */ SPI_I2S_SendData(SPIx, data); /* Wait to receive a byte */ while (SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_RXNE) == RESET) {} /* Empty the receive buffer */ SPI_I2S_ReceiveData(SPIx); /* Chip select, high */ GPIO_SetBits(W5500_CS_PORT, W5500_CS_PIN); } // 从W5500读取一个字节数据 uint8_t W5500_ReadByte(void) { uint8_t data; /* Chip select, active low */ GPIO_ResetBits(W5500_CS_PORT, W5500_CS_PIN); /* Send dummy byte to generate clock */ SPI_I2S_SendData(SPIx, 0xFF); /* Wait to receive a byte */ while (SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_RXNE) == RESET) {} /* Read the received data */ data = SPI_I2S_ReceiveData(SPIx); /* Chip select, high */ GPIO_SetBits(W5500_CS_PORT, W5500_CS_PIN); return data; } int main(void) { /* 初始化SPI */ SPIx_Init(); while (1) { /* 通过SPI与W5500进行通信 */ /* 写入数据 */ W5500_WriteByte(0x01); /* 读取数据 */ uint8_t data = W5500_ReadByte(); /* 处理接收到的数据 */ } }以上代码使用了STM32F103C8T6芯片的SPI1和GPIOA,将SPI1配置为主机模式,并定义了W5500芯片的片选引脚为GPIOB的Pin 12。在主函数中,首先通过SPIx_Init()函数初始化SPI,然后循环进行SPI通信。在循环中,可以使用W5500_WriteByte()函数向W5500芯片写入一个字节的数据,使用W5500_ReadByte()函数从W5500芯片读取一个字节的数据。
注意,以上代码只是一个示例,具体的SPI通信协议和操作需要根据W5500芯片的数据手册和具体需求进行相应的设置和实现。同时,需要在工程中添加相应的STM32库和配置。
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.