Cotton mepiquat chloride cut out dosis in parameters like(l/ha)
- User
Cotton mepiquat chloride cut out dosis in parameters like(l/ha)
Assistant
Mepiquat Chloride Applications in Cotton at Cutout
Mepiquat chloride (MC) is a plant growth regulator widely used in cotton production to control vegetative growth, resulting in a more compact plant structure that can improve harvest efficiency. However, the timing and dosage of MC applications significantly impact their effectiveness, particularly at the cutout stage of cotton development.
Effectiveness of Cutout Applications
Research indicates that mepiquat chloride applications at physiological cutout (when nodes above white bloom = 3 to 4) have limited effectiveness compared to earlier applications:
"At most locations, cutout applications of MC had little or no practical effect on plant height, nearly all growth characteristics, crop maturity, defoliation, regrowth potential, yield, or fiber quality"[6].
This suggests that applying MC at cutout offers minimal advantages in plant management, and may even be detrimental in some cases. In fact, MC applied at cutout reduced lint percentage by 1.7% and reduced lint yield by 2.6% in some studies[6].
Dosage Rates for Cutout Applications
Despite the limited effectiveness, when MC is applied at cutout, the following dosage parameters are typically used:
- Rate used in research: 0.05 kg ai ha-1 (approximately 1.19 L/ha for standard 4.2% MC formulations)[6]
- Maximum single application: 24 oz/acre (approximately 1.75 L/ha)[2][10]
- Maximum seasonal total application: 48 oz/acre (approximately 3.5 L/ha)[1][10]
Recommended Application Patterns
While cutout applications show limited benefits, the standard MC application patterns that have shown greater effectiveness include:
-
Early Bloom Application:
- 8 oz/acre (approximately 0.58 L/ha) at or prior to first bloom
- Followed by 16 oz/acre (approximately 1.17 L/ha) two weeks after the first application[1]
-
Low Rate Multiple (LRM) Strategy:
- Beginning at matchhead square: 2-8 oz/acre (0.15-0.58 L/ha)
- Multiple applications at 1-2 week intervals
- Later applications may increase to 8 oz/acre (0.58 L/ha)[2][10]
-
Single Application at 50 DAS:
- Research suggests that a single application of 300 mL/ha (0.3 L/ha) at 50 days after sowing produced optimal results for yield and plant structure[7]
Factors Influencing Dosage Decisions
The application rate of MC should be adjusted based on several factors:
Higher Mepiquat Application Rates Needed Lower Mepiquat Application Rates Needed Favorable growing conditions Water scarcity Tall-growing varieties Compact varieties High risk of boll rot Heavy fruit set Higher nitrogen application Limited nitrogen Late planting Plant injury/stress Temperature Considerations
Temperature significantly impacts MC effectiveness:
- Optimal temperature range: Day 32°C/Night 22°C
- In cooler conditions (Day 20°C/Night 10°C), MC can cause stunting
- At high temperatures, MC effectiveness on height control decreases[8]
Formulations and Active Ingredient Rates
Different MC formulations are available with varying concentrations of active ingredient:
- Standard mepiquat chloride: 0.34 to 1 ounce a.i. per acre (approximately 24-71 g a.i./ha)
- Mepiquat pentaborate: 0.77 to 2.3 ounces a.i. per acre (approximately 54-163 g a.i./ha)[1]
Practical Recommendations
Based on the research findings, for optimal cotton management:
- Focus MC applications earlier in the growing season (pre-bloom to early bloom) rather than at cutout
- If applying at cutout, use lower rates (around 0.05 kg a.i./ha or 1.19 L/ha of standard formulation)
- Consider environmental conditions carefully before application, as MC in suboptimal conditions can lead to stunting
- Observe the maximum seasonal total of 48 oz/acre (3.5 L/ha)[10]
- Allow a minimum of 7 days between applications[8]
The evidence suggests that mepiquat chloride provides the greatest benefits when applied earlier in the growing season, with cutout applications offering minimal advantages in most production scenarios.
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.