Skip to content
TheChatArchiveThe Chat Archive
Perplexitysonar-reasoning-pro-high· PerplexityHugging Face LMArena Search Arena 24K

Increase dosis in parameters like 25% or 50% according to growth and internode lemght?In…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Geminigemini-2.5-pro-exp-03-25-grounding’s answer.
  1. User

    Increase dosis in parameters like 25% or 50% according to growth and internode lemght?In cotton crop growth regulator use

  2. Perplexity Assistant

    Adjusting Cotton Growth Regulator Dosage Based on Growth Parameters

    Plant growth regulators (PGRs), particularly mepiquat chloride (MC), are essential tools for managing cotton growth. The application rate of these regulators should be adjusted based on plant growth parameters to achieve optimal results. Effective dosage adjustment relies on careful monitoring of plant growth indicators and understanding the factors that influence vegetative development.

    Key Growth Parameters for Monitoring

    The most reliable growth parameters for determining PGR application rates include:

    Internode Length

    The internode length between the fourth and fifth nodes from the terminal is a critical indicator for PGR application decisions. This specific internode is used because it represents the newest portion of the plant that is fully expanded and reflects the growth potential.

    • When this internode length reaches 2-3 inches, a PGR application is typically recommended[5][8]
    • A practical field method is to determine if three or more fingers (combined width 2-3 inches) can fit in the fourth internode[5]
    • Longer internodes indicate more aggressive growth that requires higher PGR doses

    Height-to-Node Ratio (H:N)

    This ratio is calculated by dividing the plant height by the number of nodes:

    • When the H:N ratio exceeds the threshold (typically above 2.0), PGR application is recommended[8]
    • A ratio of 2.5 indicates vigorous growth requiring higher PGR rates[8]
    • Normal range would require standard or slightly lower rates

    Daily Growth Rate

    The daily increase in plant height is another important parameter:

    • Normal growth rate is approximately 1.6 cm/day (0.63 inches/day)[3]
    • Higher growth rates (above this threshold) require increased PGR doses
    • When growth regulator was applied during high growth rate periods at 50 DAS, it provided the best yield results (4,642 kg/ha)[1]

    Adjusting PGR Dosage Based on Growth Parameters

    Percentage-Based Dosage Adjustment

    While specific percentage-based adjustments (like 25% or 50%) aren't universally standardized, research and field practices support proportional increases based on growth parameters:

    1. Internode Length-Based Adjustment:

      • For internode lengths exceeding 3 inches, increase base dose by approximately 25%[5]
      • For extreme cases (internodes >3.5 inches), a 50% increase may be warranted, especially in irrigated fields[5][7]
    2. Growth Rate-Based Adjustment:

      • When daily growth rates exceed 1.5 cm/day, an increase of 25-50% over base rate is often recommended[3]
      • The research by Echer & Rosolem shows that cotton with higher growth rates required proportionally higher PGR concentrations[3]
    3. Height-to-Node Ratio Adjustment:

      • For H:N ratios exceeding 2.5, increase the standard dose by 25-30%[8]
      • For H:N ratios between 2.0-2.5, standard doses are typically sufficient
      • For ratios below 2.0, consider reducing doses by 25%[8]

    Practical Application Examples

    Research findings support these dosage adjustments:

    • In a field trial conducted during February-August 2020, the most effective dose was 300 mL of MC (compared to higher doses of 600, 900, and 1200 mL), resulting in highest yield (4,613 kg/ha)[1]
    • When growth was exceptionally vigorous, requiring multiple applications, doses were increased from 32.5 g ai/ha in areas with slower growth to 55 g ai/ha (approximately 70% increase) in zones with more aggressive growth[9]
    • In irrigated conditions with aggressive varieties, doubling the application rate (from 8 to 16 oz/acre) is common two weeks after the initial application[7]

    Factors Influencing Dosage Requirements

    Several factors determine whether higher or lower PGR doses are needed:

    Factors Requiring Higher Doses (25-50% Increase):

    • Suitable growing conditions with adequate moisture
    • Aggressive, tall-growing varieties
    • Higher nitrogen application
    • Late planting
    • Favorable conditions for boll rot[7]

    Factors Requiring Lower Doses:

    • Water scarcity/drought conditions
    • Short, more compact varieties
    • Heavy fruit set
    • Restricted nitrogen application
    • Plant injury[7]

    Application Strategies

    Two main approaches for PGR application include:

    Low-Rate Multiple Strategies (LRM)

    • Multiple low-dose applications (2-4 oz/acre) initiated at squaring stage
    • Subsequent applications based on crop growth rate
    • Appropriate for dryland/rainfed conditions to avoid over-regulation[7]

    Plant Monitoring Approach

    • Establishes desired plant height and expected number of nodes
    • Calculates MC threshold by dividing desired height by expected nodes
    • More appropriate for irrigated cotton and high-growth scenarios
    • Allows for precise dosage adjustments (25-50% increases) based on actual field measurements[7]

    Conclusion

    Adjusting PGR dosage by percentages (25% to 50%) based on growth parameters is a sound approach supported by research. The internode length between the 4th and 5th nodes, height-to-node ratio, and daily growth rate serve as reliable indicators for determining when and by how much to increase PGR application rates. These adjustments help achieve the optimal balance between vegetative and reproductive growth in cotton, ultimately improving harvest efficiency and yield potential.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.