Skip to content
TheChatArchiveThe Chat Archive
Geminigemini-2.0-flash-grounding· GoogleHugging Face LMArena Search Arena 24K

How do I power cycle a usb port on Fedora? I want to turn off power for a specific USB…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Geminigemini-2.5-pro-exp-03-25-grounding’s answer.
  1. User

    How do I power cycle a usb port on Fedora? I want to turn off power for a specific USB port and then enable it again.

  2. Gemini Assistant

    To power cycle a specific USB port on Fedora, you can use the command line. Here's how you can do it:

    1. Identify the USB port: You'll need to determine the specific USB port you want to power cycle. You can use the lsusb command to list all USB devices and their corresponding bus and device numbers.

      • Open a terminal.
      • Type lsusb and press Enter. This will give you a list of connected USB devices. Note the Bus and Device number of the device connected to the port you wish to power cycle. For example, you might see something like Bus 002 Device 003: ...
    2. Unbind the USB device: The next step involves unbinding the device from the USB port. This effectively disconnects the device. You'll use the usb-storage module (or the appropriate module for your device, if it's not storage).

      • You need root privileges for this step. Use sudo before the command.

      • The command format is: sudo sh -c 'echo -n "Bus-Number Device-Number" > /sys/bus/usb/drivers/usb-storage/unbind'

      • Replace "Bus-Number" and "Device-Number" with the actual bus and device numbers you found with lsusb. For example, if your device was on Bus 002 and Device 003, the command would be:

        sudo sh -c 'echo -n "2-3" > /sys/bus/usb/drivers/usb-storage/unbind'
        
      • If the device is not a storage device, the driver might be different than usb-storage. You can find the driver in use with lsusb -v and look for the Driver= line in the device's information.

    3. Rebind the USB device: To re-enable the port, you need to rebind the device to the USB port:

      • The command format is similar: sudo sh -c 'echo -n "Bus-Number Device-Number" > /sys/bus/usb/drivers/usb-storage/bind'

      • Using the same example as above, the command would be:

        sudo sh -c 'echo -n "2-3" > /sys/bus/usb/drivers/usb-storage/bind'
        

    Important Considerations:

    • Data Loss: Power cycling a USB port will disconnect the device. Make sure there is no data being transferred to or from the device before you do this, to avoid data loss or corruption.
    • Alternative Method (usbreset): There's a utility called usbreset that can sometimes be used to reset USB devices. You might need to install it first (e.g., sudo dnf install usbreset). Then, you can use it with the bus and device number: sudo usbreset /dev/bus/usb/Bus/Device. (Replace Bus and Device with the actual numbers.)
    • Device Support: Not all USB devices respond well to this type of power cycling. Some devices might require a full system reboot to properly reset.
    • GUI Tools: While command-line methods are common for this task, there might be GUI-based tools available that provide a more user-friendly way to manage USB devices on Fedora. However, these are less common for specifically power cycling ports.
    • USB Hubs: If the device is connected to a USB hub, you might be able to power cycle the entire hub instead of individual ports, but this would affect all devices connected to that hub.
    • lsusb -v: Using lsusb -v provides more verbose output, including driver information, which is useful if the standard usb-storage driver doesn't work.

    Before proceeding, always ensure you've identified the correct USB device and understand the potential consequences of disconnecting it.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.