Skip to content
TheChatArchiveThe Chat Archive
Mistralmagistral-medium-2506· Mistral AIHugging Face LMArena Human Preference 140K

If I wanted to make a transistor at home in the EU that worked with 5v logic, what would…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Qwenqwen3-235b-a22b-no-thinking’s answer.
  1. User

    If I wanted to make a transistor at home in the EU that worked with 5v logic, what would my best approach be?

  2. Mistral Assistant

    Summary

    To make a transistor at home in the EU that works with 5V logic, the most feasible approach is to create a point-contact transistor using a germanium crystal. Here's a step-by-step guide:

    1. Obtain a Germanium Crystal: Salvage it from an old germanium diode or transistor.
    2. Prepare the Crystal: Clean the crystal to ensure good contact.
    3. Create Contacts:
      • Use fine wires for the emitter and collector contacts.
      • Use a larger contact or the crystal body as the base.
    4. Assemble the Transistor:
      • Mount the crystal on a non-conductive surface.
      • Attach the emitter and collector wires to the crystal.
      • Connect the base contact.
    5. Test the Transistor:
      • Set up a circuit with a 5V power supply.
      • Connect the emitter to ground and the collector to the positive supply through a load.
      • Apply a small voltage to the base to control the current between the emitter and collector.

    This method is more of an educational experiment and may not yield a high-performance transistor, but it provides a hands-on approach to understanding transistor fundamentals. For practical applications, purchasing a commercial transistor would be more reliable.

    If you're looking for a more modern approach, consider using carbon-based materials or other semiconductors, but these methods are more complex and less likely to yield a functional 5V logic transistor without specialized equipment.

    For a truly homemade transistor that can work with 5V logic, the point-contact transistor using germanium is a reasonable starting point. Keep in mind that the performance may not be perfect, and some experimentation will be necessary to get it working correctly.

    Final Answer

    To make a transistor at home in the EU that works with 5V logic, follow these steps:

    1. Obtain a Germanium Crystal: Salvage it from an old germanium diode or transistor.
    2. Prepare the Crystal: Clean the crystal to ensure good contact.
    3. Create Contacts:
      • Use fine wires for the emitter and collector contacts.
      • Use a larger contact or the crystal body as the base.
    4. Assemble the Transistor:
      • Mount the crystal on a non-conductive surface.
      • Attach the emitter and collector wires to the crystal.
      • Connect the base contact.
    5. Test the Transistor:
      • Set up a circuit with a 5V power supply.
      • Connect the emitter to ground and the collector to the positive supply through a load.
      • Apply a small voltage to the base to control the current between the emitter and collector.

    This method is more of an educational experiment and may not yield a high-performance transistor, but it provides a hands-on approach to understanding transistor fundamentals. For practical applications, purchasing a commercial transistor would be more reliable.

  3. User

    could I just use germanium and splutter it onto surfaces not exposed by photo-resist, and then dope it somehow?

  4. Mistral Assistant

    To make a transistor at home in the EU that works with 5V logic using germanium and sputtering, follow these steps:

    1. Obtain Materials:

      • Germanium (from an old diode or transistor).
      • Photoresist and a UV light source (like a UV LED).
      • Dopants (phosphorus for n-type or boron for p-type).
      • A vacuum chamber for sputtering (could be a modified bell jar).
      • A high voltage supply for sputtering.
    2. Prepare the Substrate:

      • Clean the substrate thoroughly.
      • Apply photoresist and pattern it using UV light and a mask.
    3. Sputter Germanium:

      • Set up your sputtering system.
      • Create a vacuum and apply high voltage to sputter germanium onto the substrate.
    4. Dope the Germanium:

      • Heat the germanium in the presence of your chosen dopant to diffuse the dopant into the germanium.
    5. Pattern and Etch:

      • Use photolithography to define the different regions of the transistor.
      • Etch away unwanted germanium using a suitable etchant.
    6. Create Contacts:

      • Deposit conductive material for the contacts.
      • Pattern the contacts using photolithography if necessary.
    7. Test the Transistor:

      • Set up a test circuit with a 5V power supply.
      • Measure the current-voltage characteristics to see if the transistor is working.

    Given the complexity and the equipment needed, a more feasible approach for a home project is to create a point-contact transistor using a germanium crystal and fine wires for the contacts. This method is simpler and more likely to yield a functional, albeit primitive, transistor that can work with 5V logic.

    For a truly homemade transistor that can work with 5V logic, the point-contact transistor using germanium is a reasonable starting point. Keep in mind that the performance may not be perfect, and some experimentation will be necessary to get it working correctly.

    If you're looking for a more modern approach, consider using carbon-based materials or other semiconductors, but these methods are more complex and less likely to yield a functional 5V logic transistor without specialized equipment.

    In conclusion, while it's possible to attempt making a transistor at home using sputtering and doping, it's quite challenging. A more practical approach for a home setup is to create a point-contact transistor using a germanium crystal and fine wires for the contacts. This method is simpler and more likely to yield a functional transistor that can work with 5V logic.

  5. User

    the spluttering seems like the easy bit, the material choice is the hard bit.. If I had 3 conductors going in to an area, could I just buy some high purity germanium and splutter it on, and if a doping agent would make it work better, which should I use?

  6. Mistral Assistant

    To make a transistor at home in the EU that works with 5V logic using sputtering and doping, follow these steps:

    1. Obtain High Purity Germanium: Purchase high purity germanium powder or a small piece of germanium.
    2. Set Up Sputtering: Create a simple sputtering setup using a vacuum chamber (could be a modified bell jar), a high voltage supply, and a germanium target.
    3. Patterning:
      • Apply photoresist to your substrate.
      • Use a mask to define the areas where germanium will be deposited.
      • Expose the photoresist to UV light and develop it to reveal the pattern.
    4. Sputter Germanium: Deposit germanium onto the patterned substrate.
    5. Doping:
      • For n-type regions: Use phosphorus. Heat the germanium in the presence of phosphorus vapor to diffuse phosphorus into the germanium.
      • For p-type regions: Use boron. Heat the germanium in the presence of boron powder to diffuse boron into the germanium.
    6. Contact Formation:
      • Deposit a conductive material (like aluminum) to form the contacts.
      • Pattern the contacts using photolithography if necessary.
    7. Testing:
      • Set up a test circuit with a 5V power supply.
      • Connect the emitter to ground, the collector to the positive supply through a load, and apply a small voltage to the base to control the current between the emitter and collector.

    For a simpler approach, consider making a point-contact transistor using a germanium crystal and fine wires for the contacts. This method is more accessible for a home setup and can still yield a functional transistor that works with 5V logic.

    Doping Details

    For doping, you can use the following methods:

    • Phosphorus Doping (n-type):
      • Place a small amount of red phosphorus near the germanium.
      • Heat the setup to around 600-700°C for a short period to diffuse phosphorus into the germanium.
    • Boron Doping (p-type):
      • Place boron powder near the germanium.
      • Heat the setup to diffuse boron into the germanium.

    Transistor Structure

    For an npn transistor:

    1. Start with a p-type base region.
    2. Create n-type emitter and collector regions on either side of the base.

    For a pnp transistor:

    1. Start with an n-type base region.
    2. Create p-type emitter and collector regions on either side of the base.

    Testing the Transistor

    To test if your transistor is working:

    1. Connect the emitter to ground.
    2. Connect the collector to a positive voltage (5V) through a load resistor (e.g., 1kΩ).
    3. Apply a small voltage to the base.
    4. Measure the voltage across the load resistor. If the transistor is working, you should see a change in voltage when you vary the base voltage.

    Safety Considerations

    • Handle germanium dust, phosphorus, and boron compounds with care, as they can be toxic.
    • Use proper insulation and grounding when working with high voltages for sputtering.
    • Take precautions to avoid burns when working with high temperatures during doping.

    For a simpler approach, consider making a point-contact transistor using a germanium crystal and fine wires for the contacts. This method is more accessible for a home setup and can still yield a functional transistor that works with 5V logic.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.