Can dell uefi pre-boot behaviour setting get changed to thorough without user…
- User
Can dell uefi pre-boot behaviour setting get changed to thorough without user intervention?
- Assistant
Short answer
Yes – the value stored in “F2 → BIOS Setup → POST / Pre-Boot Behaviour → Fastboot = Thorough” can flip to “Thorough” even if nobody has opened the BIOS menu, but only when something else has written to, or reset, the BIOS-NVRAM where that option lives. It does not change “all by itself”.When can it happen?
-
Firmware/BIOS flash
• A BIOS/UEFI update occasionally restores Dell-default values.
• Dell generally tries to preserve settings, but if the update contains a new NVRAM layout or a “reset to default” flag, Fastboot returns to its factory default (usually “Thorough”).
• Capsule updates pushed by Windows Update, Dell Command Update, SCCM, etc. count as “a BIOS flash”. -
Remote-management tools
• Dell Command | Configure, CCTK, OMCI, iDRAC, Intel AMT, WMI, PowerShell scripts or SCCM task sequences can all write that setting.
• An enterprise admin could deploy a policy that silently flips Fastboot to Thorough. -
CMOS / RTC battery loss or a clear-CMOS event
• If the coin-cell battery is weak or removed, or the “CMOS reset” jumper is shorted, the machine falls back to factory defaults → Thorough. -
UEFI self-protection logic (single-boot override)
• After three failed boots, a thermal event, or certain POST errors, some Dell models temporarily force a thorough POST on the next boot.
• The menu will show “Thorough” for that boot, but the stored setting usually reverts to whatever it was before once the machine starts normally.
• That looks as if the setting “changed”, but technically it was an override, not a write to NVRAM. -
Rare edge cases
• Corrupted NVRAM block caused by a brown-out or a firmware bug.
• Replacing the main board (service swap) obviously brings factory defaults.
When can’t it happen?
• Normal Windows/Linux operation cannot change that field unless a driver or application with Dell BIOS-Config capability is run.
• Malware would need admin rights plus vendor-specific code; it is possible but very uncommon.
• The BIOS itself never randomly flips the value without one of the triggers above.How to check / prevent it
• Audit logs: Dell enterprise tools (DCU, SCCM, etc.) can log every BIOS-setting change.
• BIOS setup password: set one to block unauthorised local or scripted changes.
• Disable capsule updates in BIOS if you want full manual control.
• Replace a weak CMOS battery (typically CR2032 every 5-7 years).
• After any firmware flash, export settings via Dell Command | Configure and re-import if needed.Take-away
The setting can wind up on “Thorough” without you sitting at the keyboard, but only because something (update, admin script, CMOS reset, POST-error override) actively put it there or reverted the BIOS to defaults—never because the firmware decided to toggle it for no reason. -
- User
Not remotely managed. Last firmware update in log long before change appeared. Does system enable setting after RAM or SSD changes?
- Assistant
Short version
• Simply adding / removing RAM or swapping an SSD will NOT rewrite the “Fastboot / Thorough” field that lives in BIOS-NVRAM.
• What does happen is that the firmware forces a one-time thorough POST the very next boot (to retrain memory and rescan PCIe/NVMe). During that single boot you may see a message such as “Memory has changed → Performing thorough POST”… but once the machine restarts the stored value in Setup is supposed to be whatever you had before the hardware swap.
• If you open Setup afterwards and the selector has permanently moved to “Thorough”, something else happened—most commonly a CMOS/RTC power loss while you were inside the chassis.──────────────────────────────────────── Why a hardware swap alone doesn’t flip the switch ──────────────────────────────────────── Dell’s current business and consumer platforms separate:
-
The saved-to-NVRAM user choice
POST Behaviour → Fastboot = Minimal | Auto | Thorough -
A volatile, one-boot override that the firmware asserts after:
• a DIMM population change (needs full memory test)
• a PCIe device change (re-enumeration)
• three consecutive failed boots, thermal trip, etc.
That override lasts for one boot cycle only (actually until the system reaches S4/S5 again). The menu item is NOT rewritten.
You can observe it this way:
- Set Fastboot to Minimal.
- Boot to Windows, shut down, open the case, add/remove a DIMM.
- Power on → you get the long Dell logo progress bar and maybe a message mentioning “Memory change detected – running thorough POST”.
- Enter BIOS now and you’ll still see “Minimal” selected.
──────────────────────────────────────── Scenarios that can reset the option during a RAM/SSD job ──────────────────────────────────────── While you are inside the laptop/desktop it is easy to trigger an NVRAM clear without noticing:
-
Coin-cell / RTC battery unplugged
• Many Dell laptops need the main battery removed before you can reach the SSD or DIMMs.
• On Latitudes/Precisions, pulling the main battery also cuts power to the RTC circuit if the coin-cell is weak → CMOS wiped → BIOS falls back to factory defaults, and factory default for Fastboot is “Thorough”. -
“CMOS reset” jumper accidentally shorted (desktops/towers).
-
Prolonged power-loss on a nearly-dead coin-cell (≥ 30 s with no AC adapter and no main battery).
If the date/time were wrong on the next boot, that’s a dead giveaway that CMOS was cleared.
──────────────────────────────────────── SSD swaps ──────────────────────────────────────── An NVMe or SATA drive change triggers only the one-time thorough POST; it does not alter any saved setting. SSD work alone therefore cannot explain a permanent flip to “Thorough”.
──────────────────────────────────────── What to check next ──────────────────────────────────────── • Did system clock reset to 2001/2012/…?
→ Then CMOS/RTC battery needs replacing; all settings revert to default.• Batteries pulled while servicing?
→ Normal, but couple that with a weak coin-cell and you get the same result.• Re-apply your preferred settings, then export a baseline (Dell Command | Configure can create a .exe or .csv). After future hardware work you can import it in seconds if the BIOS ever clears again.
──────────────────────────────────────── Take-away ──────────────────────────────────────── RAM or SSD replacements only cause a transient thorough POST. If the BIOS menu itself now shows “Fastboot = Thorough”, the machine lost or reset its NVRAM (usually because RTC power was interrupted) rather than because the hardware was swapped.
-
- User
Do laptops have a CMOS battery any more? Does 'disconnecting' the battery by holding a key affect UEFI settings? How does Auto mode pre-boot work? How long should Thorough take to boot?
- Assistant
Below is a “one-pager” on the four topics you asked about, using Dell laptops as the concrete example (because their terminology is what we’ve been discussing). The same ideas are valid for most modern PCs.
────────────────────────────────────────
- Do laptops still have a CMOS / RTC battery? ──────────────────────────────────────── YES – but the form-factor has been changing.
• Business-class notebooks (Dell Latitude / Precision, HP EliteBook / Z-Book, Lenovo ThinkPad T-/P-series) – Still carry a tiny 3 V coin-cell (often CR-2032 or a thinner ML-1220) on a short lead, taped to the motherboard.
– That cell powers only the Real-Time-Clock chip and the 64-byte “CMOS” RAM that stores a small subset of BIOS defaults.• Ultrabooks, tablets and most consumer laptops
– Many have dropped the separate coin-cell and feed the RTC from the main battery pack through a protected rail.
– If you remove or electrically disconnect the main battery, the RTC instantly loses power unless an on-board super-capacitor keeps it alive for a few minutes.• What about UEFI NVRAM?
– The larger block that stores things such as Secure Boot keys, boot order and the Fastboot flag lives in flash, not in the tiny CMOS RAM, so it survives even with no battery at all.
– However, the firmware may fall back to factory defaults if it sees the CMOS area is corrupt or has been cleared, hence the apparent “settings lost” we talked about earlier.──────────────────────────────────────── 2. Does “disconnecting the battery” (by key combo or BIOS option) wipe settings? ──────────────────────────────────────── Dell gives you three common ways to shut off the main battery:
A. BIOS Setup → “Internal Battery Disable”
• Cuts the pack off from the system board at the fuel-gauge FETs.
• RTC now depends on the coin-cell (if present).
• If there is no coin-cell (XPS 13, many Inspirons) the RTC dies in a few seconds → date resets → CMOS defaults reload → Fastboot flips to its factory setting (Thorough).B. “Battery Reset” hot-key (usually press & hold the power button 25 s while AC/packs are removed)
• Electrically the same end result as (A).C. Physically unplugging / removing the pack during a repair
• Same as above.So: Holding the key itself doesn’t clear UEFI, but the act of removing all power can if the machine relies on that main pack for RTC power.
Tip: If you must disconnect the pack and your model has no coin-cell, just plug AC back in for 10 s every few minutes while servicing; that keeps the RTC alive.
──────────────────────────────────────── 3. How does Fastboot = “Auto” actually work? ──────────────────────────────────────── Dell’s definition (UEFI manuals Nov-2023):
• Minimal – Skip memory test, skip S.M.A.R.T., skip USB enumeration, go straight to boot loader.
• Thorough – Run full memory test, re-enumerate all busses, spin up every drive, display any POST errors.
• Auto – Behaves like Minimal unless one of these is true:
a) hardware inventory changed ─ RAM, CPU, SSD, dock, PCIe card
b) previous POST failure (2× or 3× no-boot)
c) thermal event, watchdog reset, or the firmware-maintained “time since last thorough > 30 days/30 boots” counter expired.When (a–c) fire, the BIOS sets an internal “ForceThoroughOnce” flag → next power-on runs a single thorough POST. That flag is volatile, so your chosen mode (“Auto”) remains selected in Setup.
──────────────────────────────────────── 4. How long should a Thorough POST take? ──────────────────────────────────────── Rough numbers for current Latitudes / XPS with NVMe SSDs and no spinning disks:
• 8 GB RAM : 8-12 s
• 16 GB : 12-20 s
• 32 GB : 18-30 s
• 64 GB & ECC rigs : 30-45 sAdd 3-5 s if a SATA HDD is attached (spin-up & S.M.A.R.T.).
Add more if you enabled full memory tests like “Memory ≥ 4 GB Thorough” in the Diagnostics menu.If a “Thorough” POST takes several minutes, the firmware is probably stuck on a failing DIMM or drive and will eventually throw an error code.
──────────────────────────────────────── Key take-aways ──────────────────────────────────────── • Modern laptops do still have an RTC power source; sometimes it’s the same battery that runs the computer.
• Killing all power—even momentarily—can reset the tiny CMOS block, which then makes the BIOS fall back to vendor defaults such as Fastboot = Thorough.
• Fastboot “Auto” is simply Minimal plus smart triggers that request one-time thorough checks after changes or errors.
• A genuine Thorough POST is usually under 30 s on today’s hardware; minutes indicate trouble.Hope that de-mystifies things! If you’d like deeper internals (e.g., exact NVRAM variable names or how to script the setting), just let me know.
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.