Skip to content
TheChatArchiveThe Chat Archive
DeepSeekdeepseek-v3-0324· DeepSeekHugging Face LMArena Human Preference 140K

check firewall for astra linux eth3 udp connection

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Geminigemini-2.5-pro-preview-03-25’s answer.
  1. User

    check firewall for astra linux eth3 udp connection

  2. DeepSeek Assistant

    To check if a firewall is blocking UDP connections on interface eth3 in Astra Linux, follow these steps:


    1. Check Firewall Status

    First, verify if the firewall is active:

    sudo systemctl status iptables   # For Astra Linux 1.x (based on RHEL/CentOS)
    sudo systemctl status nftables   # For Astra Linux 2.x (based on Debian)
    

    If the firewall is enabled, proceed to inspect the rules.


    2. Check Firewall Rules for UDP on eth3

    For Astra Linux 1.x (iptables-based)

    sudo iptables -L -n -v | grep eth3
    sudo iptables -L -n -v | grep UDP
    
    • If no rules appear, UDP traffic is allowed by default.
    • If there are DROP or REJECT rules for UDP on eth3, the firewall is blocking traffic.

    For Astra Linux 2.x (nftables-based)

    sudo nft list ruleset | grep eth3
    sudo nft list ruleset | grep udp
    
    • Look for rules that explicitly block (drop, reject) UDP traffic on eth3.

    3. Temporarily Disable Firewall for Testing

    To confirm if the firewall is the issue, temporarily disable it:

    # For iptables (Astra Linux 1.x)
    sudo systemctl stop iptables
    
    # For nftables (Astra Linux 2.x)
    sudo systemctl stop nftables
    

    Now test your UDP connection (e.g., using nping or your application).
    If it works, the firewall was blocking it.

    ⚠️ Important: Re-enable the firewall after testing:

    sudo systemctl start iptables   # or nftables
    

    4. Allow UDP Traffic on eth3

    For iptables (Astra Linux 1.x)

    sudo iptables -A INPUT -i eth3 -p udp -j ACCEPT
    sudo service iptables save    # Save changes (if applicable)
    

    For nftables (Astra Linux 2.x)

    sudo nft add rule inet filter input iif eth3 udp accept
    sudo nft list ruleset > /etc/nftables.conf   # Save changes
    

    5. Verify UDP Port Access

    Use nping to test if UDP is working:

    sudo nping --udp -p <PORT> -c 3 <TARGET_IP> --interface eth3
    
    • If you get responses, the connection is open.
    • If blocked, check logs:
      sudo dmesg | grep DROP
      sudo journalctl -xe | grep firewall
      

    6. Check SELinux (if applicable)

    Astra Linux may use SELinux, which can block network traffic:

    sudo getenforce   # Check if enforcing
    sudo setenforce 0 # Temporarily disable (for testing)
    

    If UDP works after disabling SELinux, adjust policies:

    sudo ausearch -m avc -ts recent | grep udp
    sudo audit2allow -a
    

    Summary

    1. Check firewall status (iptables/nftables).
    2. Inspect rules for eth3 and UDP.
    3. Test with firewall disabled.
    4. Allow UDP if blocked.
    5. Check SELinux if still blocked.

    This should help identify and resolve UDP blocking issues on eth3 in Astra Linux. 🚀

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.