Skip to content
TheChatArchiveThe Chat Archive
Googlegemma-3-27b-it· GoogleHugging Face LMArena Human Preference 140K

i want my particles to burst quickly but not travel far in unity's particle system. what…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Geminigemini-2.5-flash-preview-04-17’s answer.
  1. User

    i want my particles to burst quickly but not travel far in unity's particle system. what are the values i should set?

  2. Google Assistant

    Okay, let's dial in those particle settings for a quick burst with limited travel distance in Unity's Particle System. Here's a breakdown of the key settings and recommended values, along with explanations:

    1. Emission Module:

    • Rate over Time: This controls how many particles are emitted per second. For a quick burst, set this to a relatively high value. Start around 50-200 and adjust to your liking. Higher values = more intense burst.
    • Burst: This is crucial for a quick, concentrated burst.
      • Count: Set this to the total number of particles you want in the burst. 50-150 is a good starting point.
      • Time: Set this to a very small value, like 0.1 - 0.3 seconds. This determines how quickly the burst happens. Smaller values = faster burst.
    • Disable Emission: Consider checking this box after the burst to stop particles from continuing to be created. You can control this with a curve if you want a fading effect.

    2. Shape Module:

    • Shape: Choose a shape that suits your effect. Cone or Sphere are good choices for bursts.
    • Radius: If using a Sphere, keep this small (e.g., 0.1 - 0.5) to keep the initial spread contained.
    • Angle: If using a Cone, keep the angle relatively narrow (e.g., 10-30 degrees) to limit the spread.
    • Position: Adjust the position to where you want the burst to originate.

    3. Velocity over Lifetime Module:

    • Linear: This is where you control how far the particles travel. Set the X, Y, and Z values to low values (e.g., 0.1 - 0.5). Lower values = less travel distance. You can also use a curve to control the velocity over the particle's lifetime. A curve that starts high and quickly drops to zero will give a quick initial push followed by rapid deceleration.
    • Orbital: Leave this at zero unless you want the particles to orbit.

    4. Size over Lifetime Module:

    • Size: You can use a curve here to make the particles shrink over time, which can enhance the burst effect. Start with a curve that starts at 1 and gradually decreases to 0.

    5. Color over Lifetime Module:

    • Color: Use a gradient to change the color of the particles over their lifetime. This can add visual interest.

    6. Renderer Module:

    • Material: Choose a material that suits your effect. A simple additive material (e.g., Particles/Additive) is often good for bursts.
    • Render Mode: Billboard is usually the best choice for particles.

    7. Physics Module (Important for limiting travel):

    • Gravity Modifier: Set this to a negative value (e.g., -1 to -5) to pull the particles down quickly. This will reduce their travel distance.
    • Damping: Increase this value (e.g., 0.5 - 1.0) to quickly reduce the particles' velocity.
    • Simulation Space: Set to Local if you want the particles to move relative to the particle system's transform. Set to World if you want them to move in world space.

    Summary of Key Values to Start With:

    • Emission Rate over Time: 50-200
    • Burst Count: 50-150
    • Burst Time: 0.1-0.3
    • Velocity over Lifetime (Linear): 0.1-0.5 (X, Y, Z)
    • Gravity Modifier: -1 to -5
    • Damping: 0.5-1.0

    Workflow:

    1. Start with the Emission: Get the burst rate and count right first.
    2. Control Velocity: Adjust the Velocity over Lifetime to limit travel distance.
    3. Add Gravity/Damping: Use the Physics module to pull the particles down and slow them down.
    4. Fine-Tune: Adjust the other modules (Size, Color, Renderer) to achieve the desired visual effect.

    Important: These are starting points. The best values will depend on the specific look you're trying to achieve. Experiment and iterate until you get the result you want! Don't be afraid to play with the curves in the modules to create more complex and interesting effects.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.