Skip to content
TheChatArchiveThe Chat Archive
chatgpt-4o-latest-20250326· OpenAIHugging Face LMArena Human Preference 140K

I need to load the tun kernel module on a Red Pitaya but it is not available. How can I…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Metallama-4-maverick-17b-128e-instruct’s answer.
  1. User

    I need to load the tun kernel module on a Red Pitaya but it is not available. How can I compile and load?

  2. Assistant

    Got it — you want to load the tun kernel module on a Red Pitaya, but it's not available. Let's walk through how you can compile and load it.

    First, some context:

    • Red Pitaya runs a Linux system, often based on a custom or embedded distribution.
    • The tun module (for TUN/TAP virtual network devices) is a standard part of the Linux kernel, but it must be enabled in the kernel configuration and compiled.
    • If it's missing, you either need to compile the module separately or rebuild the kernel with it enabled.

    Here’s a step-by-step guide:


    1. Check if the module is already built into the kernel

    First, check if TUN support is built into the kernel (not as a module):

    zcat /proc/config.gz | grep TUN
    

    or

    cat /boot/config-$(uname -r) | grep TUN
    

    Look for:

    CONFIG_TUN=m
    

    or

    CONFIG_TUN=y
    
    • If =y, it’s built into the kernel — no module needed.
    • If =m, it should be available as a module (but maybe not installed).
    • If not present, you need to rebuild the kernel or module.

    Also, check if the device exists:

    ls /dev/net/tun
    

    If it exists, the TUN driver is already active.


    2. If not available, you need to compile it

    2.1. Get the Red Pitaya kernel source

    You need the exact kernel source matching your running kernel.

    Red Pitaya provides sources here:

    Clone it:

    git clone https://github.com/RedPitaya/RedPitaya.git
    cd RedPitaya
    

    Find the correct branch/tag matching your firmware version.

    Alternatively, if you know the kernel version:

    uname -r
    

    and download the matching kernel source.

    2.2. Set up cross-compilation

    Red Pitaya uses ARM processors (Zynq 7010/7020), so you need an ARM cross-compiler.

    Install a cross-compiler on your PC (Ubuntu example):

    sudo apt-get install gcc-arm-linux-gnueabihf
    

    Or use the toolchain Red Pitaya provides.

    Set environment variables:

    export ARCH=arm
    export CROSS_COMPILE=arm-linux-gnueabihf-
    

    2.3. Configure the kernel

    You need the same kernel configuration as the running system.

    If /proc/config.gz is available:

    zcat /proc/config.gz > .config
    

    Otherwise, get the config from Red Pitaya sources or firmware.

    Then enable TUN:

    make menuconfig
    

    Navigate to:

    Device Drivers -> Network device support -> Universal TUN/TAP device driver support
    

    and set it to M (module).

    Save and exit.

    2.4. Build the module

    Now build only the tun module:

    make modules_prepare
    make M=drivers/net/tun modules
    

    This will produce a tun.ko file.

    2.5. Transfer and load the module

    Copy tun.ko to your Red Pitaya (e.g., via scp):

    scp drivers/net/tun/tun.ko root@redpitaya:/root/
    

    On the Red Pitaya:

    insmod /root/tun.ko
    

    or

    modprobe tun
    

    (if you install it properly into /lib/modules/$(uname -r)/).

    Check if it loaded:

    lsmod | grep tun
    

    3. (Optional) Install the module permanently

    To make it available after reboot:

    • Copy tun.ko to /lib/modules/$(uname -r)/kernel/drivers/net/
    • Run:
    depmod -a
    
    • Add tun to /etc/modules or equivalent to auto-load at boot.

    Troubleshooting

    • Kernel version mismatch will cause invalid module format errors.
    • If you can't cross-compile, you might need to compile directly on the Red Pitaya (slow, but possible if you install build tools).
    • If you rebuild the whole kernel, you can enable TUN built-in (=y) to avoid needing a module.

    Quick alternative: Check if you can use a precompiled module

    Sometimes Red Pitaya firmware images already have TUN support but the module is missing. You might find a matching tun.ko from a similar system (same kernel version) and try loading it.


    Would you like me to also show you how to rebuild the entire Red Pitaya kernel and firmware if needed? 🚀
    (It's a bit more involved but sometimes necessary.)

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.