Skip to content
TheChatArchiveThe Chat Archive
Metallama-4-scout-17b-16e-instruct· MetaHugging Face LMArena Human Preference 140K

#include <SPI.h> // ARDUINO SPI PINS USEDD FOR MCP320X.H #include <Mcp320x.h> #include…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Claudeclaude-opus-4-20250514’s answer.
  1. User

    #include <SPI.h> // ARDUINO SPI PINS USEDD FOR MCP320X.H #include <Mcp320x.h> #include <ShiftRegister74HC595.h> #include <EEPROM.h> #include <avr/pgmspace.h>

    // Pin definitions FOR 74HC595 USING SHIFTGRGISTER74HC595.H LIBRARY #define PEAK_RESET_PIN 2 #define SR_DATA_PIN 5 #define SR_CLK_PIN 3 #define SR_LATCH_PIN 4

    //CS PIN FOR MC320X #define CS_PIN 10

    // SPI settings #define ADC_VREF 5000 // Reference voltage in mV #define ADC_CLK 1600000 // SPI clock speed in Hz #define SATURATION_THRESHOLD 3500 // Adjusted based on data

    // Resistance steps in PROGMEM (64 steps) const PROGMEM int resistanceSteps[] = { 5175, 5000, 4800, 4600, 4400, 4200, 4000, 3800, 3600, 3400, 3200, 3000, 2800, 2600, 2400, 2200, 2000, 1900, 1800, 1700, 1600, 1500, 1400, 1300, 1200, 1100, 1000, 900, 800, 700, 600, 500, 475, 450, 425, 400, 375, 350, 325, 300, 275, 250, 225, 200, 175, 150, 125, 100, 90, 80, 70, 60, 50, 40, 30, 20, 15, 12, 10, 8, 6, 4, 2, 1 }; const int numSteps = sizeof(resistanceSteps) / sizeof(resistanceSteps[0]); int currentStep = 0;

    // Attenuation settings const int ATTENUATION_STEPS[] = {0, 10, 20, 30}; uint8_t currentAttenuationIndex = 0; float attenuationFactor = 1.0;

    // Measurement variables float V_shunt_RMS = 0.0; float emaRMS = 0.0; float emaPosPeak = 0.0; float emaNegPeak = 0.0; uint16_t rawRMS0 = 0, rawRMS1 = 0, rawRMS2 = 0; uint16_t rawPosPeak = 0, rawNegPeak = 0; const float ALPHA = 0.3; float rmsVoltage = 0.0; float posPeak = 0.0; float negPeak = 0.0; float current = 0.0; float power = 0.0; float crestFactor = 0.0; float peakToPeak = 0.0; uint8_t activeChannel = 1; float V_cal_RMS = 0.0; float V_cal_posPeak = 0.0; float V_cal_negPeak = 0.0;

    // Calibration variables const int CAL_POINTS = 10; float rmsOffset0 = 0.0, rmsOffset1 = 0.0, rmsOffset2 = 0.0; float posPeakOffset = 0.0, negPeakOffset = 0.0; const PROGMEM float calRMS0Values[CAL_POINTS] = {0.0, 0.00354, 0.01061, 0.01768, 0.03536, 0.07071, 0.10607, 0.14142, 0.17678, 0.21213}; // Gain 100, 0 to 0.60 Vpp const PROGMEM float calRMS1Values[CAL_POINTS] = {0.0, 0.28284, 0.56568, 0.84853, 1.13137, 1.41421, 1.69706, 1.97990, 2.26274, 2.82843}; // Gain 1, 0 to 8 Vpp const PROGMEM float calRMS2Values[CAL_POINTS] = {0.0, 0.07071, 0.14142, 0.21213, 0.28284, 0.35355, 0.42426, 0.49497, 0.56568, 0.63640}; // Gain 10, 0 to 1.8 Vpp const PROGMEM float calPPValues[CAL_POINTS] = {0.0, 0.5, 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0}; // Peak-to-Peak, max 8 Vpp bool calibrationChan0Complete = false; bool calibrationChan1Complete = false; bool calibrationChan2Complete = false;

    // EEPROM addresses const int EEPROM_RMS0ADC = 20; const int EEPROM_RMS1ADC = 60; const int EEPROM_RMS2ADC = 100; const int EEPROM_POSPEAKADC = 140; const int EEPROM_NEGPEAKADC = 180;

    // Safety limits const float MAX_VOLTAGE = 10000; const float MAX_CURRENT = 2.2; const float R_shunt = 2.0;

    // Test configuration enum TestMode { MANUAL, CAL_CHAN0, CAL_CHAN1, CAL_CHAN2, CAL_PEAK }; TestMode currentMode = MANUAL; unsigned long previousMillis = 0; bool testRunning = false; const uint8_t SAMPLE_COUNT = 30;

    // Objects MCP3208 adc(ADC_VREF, CS_PIN); ShiftRegister74HC595 sr(2, SR_DATA_PIN, SR_CLK_PIN, SR_LATCH_PIN);

    void setup() { pinMode(PEAK_RESET_PIN, OUTPUT); Serial.begin(115200); while (!Serial) ; // Wait for Serial to initialize SPI.begin(); SPI.beginTransaction(SPISettings(ADC_CLK, MSBFIRST, SPI_MODE0)); loadCalibrationFromEEPROM(); updateVariableResistance(); setAttenuation(0); Serial.println(F("QA-ES Initialized")); }

    void loop() { unsigned long currentMillis = millis(); switch (currentMode) { case MANUAL: runManualMeasurement(currentMillis); break; case CAL_CHAN0: runCalibrationChan0(currentMillis); break; case CAL_CHAN1: runCalibrationChan1(currentMillis); break; case CAL_CHAN2: runCalibrationChan2(currentMillis); break; case CAL_PEAK: runCalibrationPeak(currentMillis); break; } if (Serial.available()) handleSerialCommand(); }

    void takeMeasurement() { resetPeaks(); delay(5);

    const uint8_t SAMPLE_AVG = 20; uint32_t rms0Sum = 0, rms2Sum = 0, rms1Sum = 0, posPeakSum = 0, negPeakSum = 0; for (uint8_t i = 0; i < SAMPLE_AVG; i++) { rms0Sum += adc.read(MCP3208::Channel::SINGLE_0); rms2Sum += adc.read(MCP3208::Channel::SINGLE_2); rms1Sum += adc.read(MCP3208::Channel::SINGLE_1); posPeakSum += adc.read(MCP3208::Channel::SINGLE_3); negPeakSum += adc.read(MCP3208::Channel::SINGLE_4); delayMicroseconds(100); } rawRMS0 = rms0Sum / SAMPLE_AVG; rawRMS2 = rms2Sum / SAMPLE_AVG; rawRMS1 = rms1Sum / SAMPLE_AVG; rawPosPeak = posPeakSum / SAMPLE_AVG; rawNegPeak = negPeakSum / SAMPLE_AVG;

    if (rawRMS0 < SATURATION_THRESHOLD) { activeChannel = 0; emaRMS = ALPHA * rawRMS0 + (1 - ALPHA) * emaRMS; } else if (rawRMS2 < SATURATION_THRESHOLD) { activeChannel = 2; emaRMS = ALPHA * rawRMS2 + (1 - ALPHA) * emaRMS; } else { activeChannel = 1; emaRMS = ALPHA * rawRMS1 + (1 - ALPHA) * emaRMS; }

    emaPosPeak = ALPHA * rawPosPeak + (1 - ALPHA) * emaPosPeak; emaNegPeak = ALPHA * rawNegPeak + (1 - ALPHA) * emaNegPeak;

    float calRMSADC[CAL_POINTS]; switch (activeChannel) { case 0: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS0ADC); V_cal_RMS = calibrationChan0Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS0Values, rmsOffset0) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0) / 100.0); break; case 2: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS2ADC); V_cal_RMS = calibrationChan2Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS2Values, rmsOffset2) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0) / 10.0); break; case 1: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS1ADC); V_cal_RMS = calibrationChan1Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS1Values, rmsOffset1) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0)); break; }

    loadArrayFromEEPROM(calRMSADC, EEPROM_POSPEAKADC); V_cal_posPeak = getCorrectedRMS(emaPosPeak, calRMSADC, calPPValues, posPeakOffset) / 2.0; loadArrayFromEEPROM(calRMSADC, EEPROM_NEGPEAKADC); V_cal_negPeak = -getCorrectedRMS(emaNegPeak, calRMSADC, calPPValues, negPeakOffset) / 2.0;

    V_shunt_RMS = V_cal_RMS * attenuationFactor; float V_shunt_posPeak = V_cal_posPeak * attenuationFactor; float V_shunt_negPeak = V_cal_negPeak * attenuationFactor;

    current = V_shunt_RMS / R_shunt; float resistance = pgm_read_word(&resistanceSteps[currentStep]); rmsVoltage = current * resistance;

    posPeak = V_shunt_posPeak; negPeak = V_shunt_negPeak;

    power = rmsVoltage * current; float maxPeak = max(fabs(posPeak), fabs(negPeak)); crestFactor = (V_shunt_RMS > 0.001) ? (maxPeak / V_shunt_RMS) : 0.0; peakToPeak = posPeak - negPeak; }

    void printResults() { float totalImpedance = pgm_read_word(&resistanceSteps[currentStep]); Serial.print(F("Chan: ")); Serial.print(activeChannel); Serial.print(F("\t")); Serial.print(F("V_shunt: ")); Serial.print(V_shunt_RMS, 3); Serial.print(F(" V\t")); Serial.print(F("V_load: ")); Serial.print(rmsVoltage, 3); Serial.print(F(" V\t")); Serial.print(F("PosP: ")); Serial.print(posPeak, 3); Serial.print(F(" V\t")); Serial.print(F("NegP: ")); Serial.print(negPeak, 3); Serial.print(F(" V\t")); Serial.print(F("Curr: ")); Serial.print(current * 1000, 3); Serial.print(F(" mA\t")); Serial.print(F("Pwr: ")); Serial.print(power, 3); Serial.print(F(" W\t")); Serial.print(F("Crest: ")); Serial.print(crestFactor, 2); Serial.print(F("\t")); Serial.print(F("P-P: ")); Serial.print(peakToPeak, 3); Serial.print(F(" V\t")); Serial.print(F("Imp: ")); Serial.print(totalImpedance); Serial.print(F(" ohm\t")); Serial.print(F("Att: ")); Serial.print(ATTENUATION_STEPS[currentAttenuationIndex]); Serial.print(F(" dB\t")); Serial.print(F("Raw0: ")); Serial.print(rawRMS0); Serial.print(F("\t")); Serial.print(F("Raw1: ")); Serial.print(rawRMS1); Serial.print(F("\t")); Serial.print(F("Raw2: ")); Serial.print(rawRMS2); Serial.print(F("\t")); Serial.print(F("RawPP: ")); Serial.print(rawPosPeak); Serial.print(F("\t")); Serial.print(F("RawNP: ")); Serial.print(rawNegPeak); Serial.println(); }

    void runManualMeasurement(unsigned long currentMillis) { takeMeasurement(); if (currentMillis - previousMillis >= 500) { printResults(); previousMillis = currentMillis; } }

    void runCalibrationChan0(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 0 (Gain 100) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan0Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS0Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 0, EEPROM_RMS0ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan0Complete = true;
          Serial.println(F("Channel 0 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationChan1(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 1 (Gain 1) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan1Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS1Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 1, EEPROM_RMS1ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan1Complete = true;
          Serial.println(F("Channel 1 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationChan2(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 2 (Gain 10) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan2Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS2Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 2, EEPROM_RMS2ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan2Complete = true;
          Serial.println(F("Channel 2 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationPeak(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Peak-to-Peak (Channels 3 and 4)...")); testRunning = true; calStep = 0; promptPrinted = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vpp = pgm_read_float(&calPPValues[calStep]); Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.println(F(" V, then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePeakPoint(calStep);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          Serial.println(F("Peak-to-Peak Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void calibratePoint(uint8_t point, uint8_t channel, int eepromBase) { uint32_t rms0Sum = 0, rms2Sum = 0, rms1Sum = 0; resetPeaks(); delay(10);

    for (uint8_t i = 0; i < SAMPLE_COUNT; i++) { rms0Sum += adc.read(MCP3208::Channel::SINGLE_0); rms2Sum += adc.read(MCP3208::Channel::SINGLE_2); rms1Sum += adc.read(MCP3208::Channel::SINGLE_1); delayMicroseconds(1000); }

    float rms0Raw = rms0Sum / SAMPLE_COUNT; float rms2Raw = rms2Sum / SAMPLE_COUNT; float rms1Raw = rms1Sum / SAMPLE_COUNT;

    float value; if (channel == 0) { value = rms0Raw; if (point == 0) rmsOffset0 = value / 4095.0 * (ADC_VREF / 1000.0) / 100.0; EEPROM.put(0, rmsOffset0); } else if (channel == 1) { value = rms1Raw; if (point == 0) rmsOffset1 = value / 4095.0 * (ADC_VREF / 1000.0); EEPROM.put(4, rmsOffset1); } else if (channel == 2) { value = rms2Raw; if (point == 0) rmsOffset2 = value / 4095.0 * (ADC_VREF / 1000.0) / 10.0; EEPROM.put(8, rmsOffset2); } EEPROM.put(eepromBase + point * sizeof(float), value); }

    void calibratePeakPoint(uint8_t point) { uint32_t posPeakSum = 0, negPeakSum = 0; resetPeaks(); delay(10);

    for (uint8_t i = 0; i < SAMPLE_COUNT; i++) { posPeakSum += adc.read(MCP3208::Channel::SINGLE_3); negPeakSum += adc.read(MCP3208::Channel::SINGLE_4); delayMicroseconds(1000); } float posPeakRaw = posPeakSum / SAMPLE_COUNT; float negPeakRaw = negPeakSum / SAMPLE_COUNT;

    EEPROM.put(EEPROM_POSPEAKADC + point * sizeof(float), posPeakRaw); EEPROM.put(EEPROM_NEGPEAKADC + point * sizeof(float), negPeakRaw);

    if (point == 0) { posPeakOffset = posPeakRaw / 4095.0 * (ADC_VREF / 1000.0); negPeakOffset = negPeakRaw / 4095.0 * (ADC_VREF / 1000.0); EEPROM.put(12, posPeakOffset); EEPROM.put(16, negPeakOffset); } }

    void loadCalibrationFromEEPROM() { EEPROM.get(0, rmsOffset0); EEPROM.get(4, rmsOffset1); EEPROM.get(8, rmsOffset2); EEPROM.get(12, posPeakOffset); EEPROM.get(16, negPeakOffset); calibrationChan0Complete = (rmsOffset0 != 0); calibrationChan1Complete = (rmsOffset1 != 0); calibrationChan2Complete = (rmsOffset2 != 0); }

    void loadArrayFromEEPROM(float* array, int eepromBase) { for (uint8_t i = 0; i < CAL_POINTS; i++) { EEPROM.get(eepromBase + i * sizeof(float), array[i]); } }

    void printCalibrationData() { float tempArray[CAL_POINTS];

    Serial.println(F("RMS0 (Gain 100):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS0ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS0Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("RMS1 (Gain 1):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS1ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS1Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("RMS2 (Gain 10):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS2ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS2Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("Positive Peak (Channel 3):")); loadArrayFromEEPROM(tempArray, EEPROM_POSPEAKADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vpp=")); Serial.print(pgm_read_float(&calPPValues[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("Negative Peak (Channel 4):")); loadArrayFromEEPROM(tempArray, EEPROM_NEGPEAKADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vpp=")); Serial.print(pgm_read_float(&calPPValues[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); } }

    float getCorrectedRMS(float adcReading, float* calADC, const float* calValues, float offset) { float value = interpolate(adcReading, calADC, calValues); return max(0, value - offset); }

    float interpolate(float adcReading, float* calADC, const float* calValues) { if (adcReading <= calADC[0]) return pgm_read_float(&calValues[0]); if (adcReading >= calADC[CAL_POINTS - 1]) return pgm_read_float(&calValues[CAL_POINTS - 1]); for (uint8_t i = 0; i < CAL_POINTS - 1; i++) { if (adcReading >= calADC[i] && adcReading <= calADC[i + 1]) { float slope = (pgm_read_float(&calValues[i + 1]) - pgm_read_float(&calValues[i])) / (calADC[i + 1] - calADC[i]); return pgm_read_float(&calValues[i]) + slope * (adcReading - calADC[i]); } } return pgm_read_float(&calValues[CAL_POINTS - 1]); }

    void handleSerialCommand() { if (Serial.available()) { String command = Serial.readStringUntil('\n'); command.trim(); while (Serial.available()) Serial.read(); // Clear remaining buffer if (command == "C0") { currentMode = CAL_CHAN0; Serial.println(F("Entering Channel 0 Calibration")); } else if (command == "C1") { currentMode = CAL_CHAN1; Serial.println(F("Entering Channel 1 Calibration")); } else if (command == "C2") { currentMode = CAL_CHAN2; Serial.println(F("Entering Channel 2 Calibration")); } else if (command == "CP") { currentMode = CAL_PEAK; Serial.println(F("Entering Peak-to-Peak Calibration")); } else if (command == "CAL") { Serial.println(F("Displaying EEPROM Calibration Data:")); printCalibrationData(); } else if (command == "0" || command == "1" || command == "2" || command == "3") { setAttenuation(command.toInt() * 10); Serial.print(F("Set attenuation to: ")); Serial.println(ATTENUATION_STEPS[currentAttenuationIndex]); } else if (command.toInt() > 0) { currentStep = findStep(command.toInt()); updateVariableResistance(); Serial.print(F("Set load to: ")); Serial.println(pgm_read_word(&resistanceSteps[currentStep])); } else { Serial.println(F("Unknown command")); } } }

    void resetPeaks() { digitalWrite(PEAK_RESET_PIN, HIGH); delayMicroseconds(20); digitalWrite(PEAK_RESET_PIN, LOW); }

    void setAttenuation(uint8_t db) { sr.setNoUpdate(10, db == 0 ? HIGH : db == 10 ? LOW : db == 30 ? LOW : HIGH); sr.setNoUpdate(11, db == 0 ? HIGH : db == 20 ? LOW : db == 30 ? LOW : HIGH); sr.updateRegisters(); currentAttenuationIndex = (db == 0 ? 0 : db == 10 ? 1 : db == 20 ? 2 : 3); attenuationFactor = pow(10, db / 20.0); }

    void updateVariableResistance() { int targetResistance = pgm_read_word(&resistanceSteps[currentStep]); for (uint8_t i = 0; i < 10; i++) sr.setNoUpdate(i, HIGH); struct ResistorPin { int value; uint8_t pin; }; const ResistorPin resistors[] = {{2000, 5}, {1600, 4}, {800, 3}, {400, 2}, {200, 1}, {100, 0}, {50, 8}, {15, 7}, {10, 9}}; int remainingResistance = targetResistance; for (const ResistorPin& rp : resistors) { if (remainingResistance >= rp.value) { sr.setNoUpdate(rp.pin, LOW); remainingResistance -= rp.value; } } sr.setNoUpdate(6, HIGH); sr.updateRegisters(); }

    int findStep(int targetResistance) { for (int i = 0; i < numSteps; i++) { if (pgm_read_word(&resistanceSteps[i]) <= targetResistance) return i; } return numSteps - 1; }

  2. Meta Assistant

    The provided code appears to be a comprehensive implementation of a measurement and calibration system for a specific hardware setup. However, there are a few potential issues and improvements that can be suggested:

    1. Magic Numbers: The code contains many magic numbers (e.g., 20, 60, 100, 10, etc.) that are not clearly explained. It would be better to define these numbers as constants with descriptive names.

    2. Code Organization: The code is quite long and complex. It might be beneficial to break it down into smaller files or classes, each responsible for a specific aspect of the system (e.g., one file for calibration, one for measurement, etc.).

    3. Error Handling: The code does not seem to handle errors well. For example, in the handleSerialCommand function, if the command is not recognized, it simply prints "Unknown command". It might be better to provide more feedback or take alternative actions.

    4. Type Conversions: The code performs many type conversions, which can be error-prone. It would be better to use explicit casting and check for potential overflows.

    5. Comments and Documentation: Although the code has some comments, it would be beneficial to have more detailed explanations of the algorithms and data structures used.

    6. EEPROM Usage: The code uses EEPROM to store calibration data. However, it does not seem to check if the data is valid or if the EEPROM is worn out. It might be beneficial to add checks for these conditions.

    Here is a minor improvement to the interpolate function:

    float interpolate(float adcReading, float* calADC, const float* calValues) {
      if (adcReading <= calADC[0]) return pgm_read_float(&calValues[0]);
      if (adcReading >= calADC[CAL_POINTS - 1]) return pgm_read_float(&calValues[CAL_POINTS - 1]);
    
      for (uint8_t i = 0; i < CAL_POINTS - 1; i++) {
        if (adcReading >= calADC[i] && adcReading <= calADC[i + 1]) {
          float slope = (pgm_read_float(&calValues[i + 1]) - pgm_read_float(&calValues[i])) / (calADC[i + 1] - calADC[i]);
          return pgm_read_float(&calValues[i]) + slope * (adcReading - calADC[i]);
        }
      }
      // If we reach this point, it means the adcReading is outside the range of calADC
      // You might want to add some error handling here
      return pgm_read_float(&calValues[CAL_POINTS - 1]);
    }
    

    Additionally, you might want to consider using a more robust interpolation method, such as cubic spline interpolation, if the relationship between adcReading and calValues is not linear.

    Here is an example of how you could refactor the runCalibrationChan0 function to make it more readable:

    void runCalibrationChan0(unsigned long currentMillis) {
      static uint8_t calStep = 0;
      static bool promptPrinted = false;
    
      if (!testRunning) {
        startCalibration(F("Channel 0 (Gain 100) RMS..."), calStep, promptPrinted, calibrationChan0Complete);
      }
    
      if (calStep < CAL_POINTS) {
        if (!promptPrinted) {
          printCalibrationPrompt(calStep);
          promptPrinted = true;
        }
    
        if (Serial.available()) {
          char c = Serial.read();
          while (Serial.available()) Serial.read(); // Clear remaining buffer
          if (c == 'Y' || c == 'y') {
            calibratePoint(calStep, 0, EEPROM_RMS0ADC);
            calStep++;
            promptPrinted = false; // Reset for next step
            if (calStep >= CAL_POINTS) {
              calibrationChan0Complete = true;
              endCalibration(F("Channel 0 RMS Calibration Complete"));
              testRunning = false;
              currentMode = MANUAL;
            }
          } else {
            Serial.println(F("Invalid input. Press 'Y' to proceed."));
          }
        }
      }
    }
    
    void startCalibration(const __FlashStringHelper* message, uint8_t& calStep, bool& promptPrinted, bool& calibrationComplete) {
      Serial.println(F("Starting Calibration for "));
      Serial.println(message);
      testRunning = true;
      calStep = 0;
      promptPrinted = false;
      calibrationComplete = false;
      while (Serial.available()) Serial.read(); // Clear buffer
    }
    
    void printCalibrationPrompt(uint8_t calStep) {
      float vrms = pgm_read_float(&calRMS0Values[calStep]);
      float vpp = 2 * sqrt(2) * vrms;
      Serial.print(F("Step ")); Serial.print(calStep + 1);
      Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4);
      Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4);
      Serial.println(F(" V), then press 'Y' to proceed."));
    }
    
    void endCalibration(const __FlashStringHelper* message) {
      Serial.println(message);
    }
    

    This refactoring makes the code more readable by extracting common code into separate functions.

  3. User

    i am providng you the working code using arduino uno.please convert this code to esp32.as i want to replace arduino uno with esp32 #include <SPI.h> // ARDUINO SPI PINS USEDD FOR MCP320X.H #include <Mcp320x.h> #include <ShiftRegister74HC595.h> #include <EEPROM.h> #include <avr/pgmspace.h>

    // Pin definitions FOR 74HC595 USING SHIFTGRGISTER74HC595.H LIBRARY #define PEAK_RESET_PIN 2 #define SR_DATA_PIN 5 #define SR_CLK_PIN 3 #define SR_LATCH_PIN 4

    //CS PIN FOR MC320X #define CS_PIN 10

    // SPI settings #define ADC_VREF 5000 // Reference voltage in mV #define ADC_CLK 1600000 // SPI clock speed in Hz #define SATURATION_THRESHOLD 3500 // Adjusted based on data

    // Resistance steps in PROGMEM (64 steps) const PROGMEM int resistanceSteps[] = { 5175, 5000, 4800, 4600, 4400, 4200, 4000, 3800, 3600, 3400, 3200, 3000, 2800, 2600, 2400, 2200, 2000, 1900, 1800, 1700, 1600, 1500, 1400, 1300, 1200, 1100, 1000, 900, 800, 700, 600, 500, 475, 450, 425, 400, 375, 350, 325, 300, 275, 250, 225, 200, 175, 150, 125, 100, 90, 80, 70, 60, 50, 40, 30, 20, 15, 12, 10, 8, 6, 4, 2, 1 }; const int numSteps = sizeof(resistanceSteps) / sizeof(resistanceSteps[0]); int currentStep = 0;

    // Attenuation settings const int ATTENUATION_STEPS[] = {0, 10, 20, 30}; uint8_t currentAttenuationIndex = 0; float attenuationFactor = 1.0;

    // Measurement variables float V_shunt_RMS = 0.0; float emaRMS = 0.0; float emaPosPeak = 0.0; float emaNegPeak = 0.0; uint16_t rawRMS0 = 0, rawRMS1 = 0, rawRMS2 = 0; uint16_t rawPosPeak = 0, rawNegPeak = 0; const float ALPHA = 0.3; float rmsVoltage = 0.0; float posPeak = 0.0; float negPeak = 0.0; float current = 0.0; float power = 0.0; float crestFactor = 0.0; float peakToPeak = 0.0; uint8_t activeChannel = 1; float V_cal_RMS = 0.0; float V_cal_posPeak = 0.0; float V_cal_negPeak = 0.0;

    // Calibration variables const int CAL_POINTS = 10; float rmsOffset0 = 0.0, rmsOffset1 = 0.0, rmsOffset2 = 0.0; float posPeakOffset = 0.0, negPeakOffset = 0.0; const PROGMEM float calRMS0Values[CAL_POINTS] = {0.0, 0.00354, 0.01061, 0.01768, 0.03536, 0.07071, 0.10607, 0.14142, 0.17678, 0.21213}; // Gain 100, 0 to 0.60 Vpp const PROGMEM float calRMS1Values[CAL_POINTS] = {0.0, 0.28284, 0.56568, 0.84853, 1.13137, 1.41421, 1.69706, 1.97990, 2.26274, 2.82843}; // Gain 1, 0 to 8 Vpp const PROGMEM float calRMS2Values[CAL_POINTS] = {0.0, 0.07071, 0.14142, 0.21213, 0.28284, 0.35355, 0.42426, 0.49497, 0.56568, 0.63640}; // Gain 10, 0 to 1.8 Vpp const PROGMEM float calPPValues[CAL_POINTS] = {0.0, 0.5, 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0}; // Peak-to-Peak, max 8 Vpp bool calibrationChan0Complete = false; bool calibrationChan1Complete = false; bool calibrationChan2Complete = false;

    // EEPROM addresses const int EEPROM_RMS0ADC = 20; const int EEPROM_RMS1ADC = 60; const int EEPROM_RMS2ADC = 100; const int EEPROM_POSPEAKADC = 140; const int EEPROM_NEGPEAKADC = 180;

    // Safety limits const float MAX_VOLTAGE = 10000; const float MAX_CURRENT = 2.2; const float R_shunt = 2.0;

    // Test configuration enum TestMode { MANUAL, CAL_CHAN0, CAL_CHAN1, CAL_CHAN2, CAL_PEAK }; TestMode currentMode = MANUAL; unsigned long previousMillis = 0; bool testRunning = false; const uint8_t SAMPLE_COUNT = 30;

    // Objects MCP3208 adc(ADC_VREF, CS_PIN); ShiftRegister74HC595 sr(2, SR_DATA_PIN, SR_CLK_PIN, SR_LATCH_PIN);

    void setup() { pinMode(PEAK_RESET_PIN, OUTPUT); Serial.begin(115200); while (!Serial) ; // Wait for Serial to initialize SPI.begin(); SPI.beginTransaction(SPISettings(ADC_CLK, MSBFIRST, SPI_MODE0)); loadCalibrationFromEEPROM(); updateVariableResistance(); setAttenuation(0); Serial.println(F("QA-ES Initialized")); }

    void loop() { unsigned long currentMillis = millis(); switch (currentMode) { case MANUAL: runManualMeasurement(currentMillis); break; case CAL_CHAN0: runCalibrationChan0(currentMillis); break; case CAL_CHAN1: runCalibrationChan1(currentMillis); break; case CAL_CHAN2: runCalibrationChan2(currentMillis); break; case CAL_PEAK: runCalibrationPeak(currentMillis); break; } if (Serial.available()) handleSerialCommand(); }

    void takeMeasurement() { resetPeaks(); delay(5);

    const uint8_t SAMPLE_AVG = 20; uint32_t rms0Sum = 0, rms2Sum = 0, rms1Sum = 0, posPeakSum = 0, negPeakSum = 0; for (uint8_t i = 0; i < SAMPLE_AVG; i++) { rms0Sum += adc.read(MCP3208::Channel::SINGLE_0); rms2Sum += adc.read(MCP3208::Channel::SINGLE_2); rms1Sum += adc.read(MCP3208::Channel::SINGLE_1); posPeakSum += adc.read(MCP3208::Channel::SINGLE_3); negPeakSum += adc.read(MCP3208::Channel::SINGLE_4); delayMicroseconds(100); } rawRMS0 = rms0Sum / SAMPLE_AVG; rawRMS2 = rms2Sum / SAMPLE_AVG; rawRMS1 = rms1Sum / SAMPLE_AVG; rawPosPeak = posPeakSum / SAMPLE_AVG; rawNegPeak = negPeakSum / SAMPLE_AVG;

    if (rawRMS0 < SATURATION_THRESHOLD) { activeChannel = 0; emaRMS = ALPHA * rawRMS0 + (1 - ALPHA) * emaRMS; } else if (rawRMS2 < SATURATION_THRESHOLD) { activeChannel = 2; emaRMS = ALPHA * rawRMS2 + (1 - ALPHA) * emaRMS; } else { activeChannel = 1; emaRMS = ALPHA * rawRMS1 + (1 - ALPHA) * emaRMS; }

    emaPosPeak = ALPHA * rawPosPeak + (1 - ALPHA) * emaPosPeak; emaNegPeak = ALPHA * rawNegPeak + (1 - ALPHA) * emaNegPeak;

    float calRMSADC[CAL_POINTS]; switch (activeChannel) { case 0: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS0ADC); V_cal_RMS = calibrationChan0Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS0Values, rmsOffset0) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0) / 100.0); break; case 2: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS2ADC); V_cal_RMS = calibrationChan2Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS2Values, rmsOffset2) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0) / 10.0); break; case 1: loadArrayFromEEPROM(calRMSADC, EEPROM_RMS1ADC); V_cal_RMS = calibrationChan1Complete ? getCorrectedRMS(emaRMS, calRMSADC, calRMS1Values, rmsOffset1) : (emaRMS / 4095.0 * (ADC_VREF / 1000.0)); break; }

    loadArrayFromEEPROM(calRMSADC, EEPROM_POSPEAKADC); V_cal_posPeak = getCorrectedRMS(emaPosPeak, calRMSADC, calPPValues, posPeakOffset) / 2.0; loadArrayFromEEPROM(calRMSADC, EEPROM_NEGPEAKADC); V_cal_negPeak = -getCorrectedRMS(emaNegPeak, calRMSADC, calPPValues, negPeakOffset) / 2.0;

    V_shunt_RMS = V_cal_RMS * attenuationFactor; float V_shunt_posPeak = V_cal_posPeak * attenuationFactor; float V_shunt_negPeak = V_cal_negPeak * attenuationFactor;

    current = V_shunt_RMS / R_shunt; float resistance = pgm_read_word(&resistanceSteps[currentStep]); rmsVoltage = current * resistance;

    posPeak = V_shunt_posPeak; negPeak = V_shunt_negPeak;

    power = rmsVoltage * current; float maxPeak = max(fabs(posPeak), fabs(negPeak)); crestFactor = (V_shunt_RMS > 0.001) ? (maxPeak / V_shunt_RMS) : 0.0; peakToPeak = posPeak - negPeak; }

    void printResults() { float totalImpedance = pgm_read_word(&resistanceSteps[currentStep]); Serial.print(F("Chan: ")); Serial.print(activeChannel); Serial.print(F("\t")); Serial.print(F("V_shunt: ")); Serial.print(V_shunt_RMS, 3); Serial.print(F(" V\t")); Serial.print(F("V_load: ")); Serial.print(rmsVoltage, 3); Serial.print(F(" V\t")); Serial.print(F("PosP: ")); Serial.print(posPeak, 3); Serial.print(F(" V\t")); Serial.print(F("NegP: ")); Serial.print(negPeak, 3); Serial.print(F(" V\t")); Serial.print(F("Curr: ")); Serial.print(current * 1000, 3); Serial.print(F(" mA\t")); Serial.print(F("Pwr: ")); Serial.print(power, 3); Serial.print(F(" W\t")); Serial.print(F("Crest: ")); Serial.print(crestFactor, 2); Serial.print(F("\t")); Serial.print(F("P-P: ")); Serial.print(peakToPeak, 3); Serial.print(F(" V\t")); Serial.print(F("Imp: ")); Serial.print(totalImpedance); Serial.print(F(" ohm\t")); Serial.print(F("Att: ")); Serial.print(ATTENUATION_STEPS[currentAttenuationIndex]); Serial.print(F(" dB\t")); Serial.print(F("Raw0: ")); Serial.print(rawRMS0); Serial.print(F("\t")); Serial.print(F("Raw1: ")); Serial.print(rawRMS1); Serial.print(F("\t")); Serial.print(F("Raw2: ")); Serial.print(rawRMS2); Serial.print(F("\t")); Serial.print(F("RawPP: ")); Serial.print(rawPosPeak); Serial.print(F("\t")); Serial.print(F("RawNP: ")); Serial.print(rawNegPeak); Serial.println(); }

    void runManualMeasurement(unsigned long currentMillis) { takeMeasurement(); if (currentMillis - previousMillis >= 500) { printResults(); previousMillis = currentMillis; } }

    void runCalibrationChan0(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 0 (Gain 100) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan0Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS0Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 0, EEPROM_RMS0ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan0Complete = true;
          Serial.println(F("Channel 0 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationChan1(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 1 (Gain 1) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan1Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS1Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 1, EEPROM_RMS1ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan1Complete = true;
          Serial.println(F("Channel 1 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationChan2(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Channel 2 (Gain 10) RMS...")); testRunning = true; calStep = 0; promptPrinted = false; calibrationChan2Complete = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vrms = pgm_read_float(&calRMS2Values[calStep]); float vpp = 2 * sqrt(2) * vrms; Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.print(F(" V (RMS = ")); Serial.print(vrms, 4); Serial.println(F(" V), then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePoint(calStep, 2, EEPROM_RMS2ADC);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          calibrationChan2Complete = true;
          Serial.println(F("Channel 2 RMS Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void runCalibrationPeak(unsigned long currentMillis) { static uint8_t calStep = 0; static bool promptPrinted = false;

    if (!testRunning) { Serial.println(F("Starting Calibration for Peak-to-Peak (Channels 3 and 4)...")); testRunning = true; calStep = 0; promptPrinted = false; while (Serial.available()) Serial.read(); // Clear buffer }

    if (calStep < CAL_POINTS) { if (!promptPrinted) { float vpp = pgm_read_float(&calPPValues[calStep]); Serial.print(F("Step ")); Serial.print(calStep + 1); Serial.print(F(": Set sine wave Vpp = ")); Serial.print(vpp, 4); Serial.println(F(" V, then press 'Y' to proceed.")); promptPrinted = true; }

    if (Serial.available()) {
      char c = Serial.read();
      while (Serial.available()) Serial.read(); // Clear remaining buffer
      if (c == 'Y' || c == 'y') {
        Serial.print(F("Calibrating step ")); Serial.print(calStep + 1); Serial.println(F("..."));
        calibratePeakPoint(calStep);
        calStep++;
        promptPrinted = false; // Reset for next step
        if (calStep >= CAL_POINTS) {
          Serial.println(F("Peak-to-Peak Calibration Complete"));
          testRunning = false;
          currentMode = MANUAL;
        }
      } else {
        Serial.println(F("Invalid input. Press 'Y' to proceed."));
      }
    }
    

    } }

    void calibratePoint(uint8_t point, uint8_t channel, int eepromBase) { uint32_t rms0Sum = 0, rms2Sum = 0, rms1Sum = 0; resetPeaks(); delay(10);

    for (uint8_t i = 0; i < SAMPLE_COUNT; i++) { rms0Sum += adc.read(MCP3208::Channel::SINGLE_0); rms2Sum += adc.read(MCP3208::Channel::SINGLE_2); rms1Sum += adc.read(MCP3208::Channel::SINGLE_1); delayMicroseconds(1000); }

    float rms0Raw = rms0Sum / SAMPLE_COUNT; float rms2Raw = rms2Sum / SAMPLE_COUNT; float rms1Raw = rms1Sum / SAMPLE_COUNT;

    float value; if (channel == 0) { value = rms0Raw; if (point == 0) rmsOffset0 = value / 4095.0 * (ADC_VREF / 1000.0) / 100.0; EEPROM.put(0, rmsOffset0); } else if (channel == 1) { value = rms1Raw; if (point == 0) rmsOffset1 = value / 4095.0 * (ADC_VREF / 1000.0); EEPROM.put(4, rmsOffset1); } else if (channel == 2) { value = rms2Raw; if (point == 0) rmsOffset2 = value / 4095.0 * (ADC_VREF / 1000.0) / 10.0; EEPROM.put(8, rmsOffset2); } EEPROM.put(eepromBase + point * sizeof(float), value); }

    void calibratePeakPoint(uint8_t point) { uint32_t posPeakSum = 0, negPeakSum = 0; resetPeaks(); delay(10);

    for (uint8_t i = 0; i < SAMPLE_COUNT; i++) { posPeakSum += adc.read(MCP3208::Channel::SINGLE_3); negPeakSum += adc.read(MCP3208::Channel::SINGLE_4); delayMicroseconds(1000); } float posPeakRaw = posPeakSum / SAMPLE_COUNT; float negPeakRaw = negPeakSum / SAMPLE_COUNT;

    EEPROM.put(EEPROM_POSPEAKADC + point * sizeof(float), posPeakRaw); EEPROM.put(EEPROM_NEGPEAKADC + point * sizeof(float), negPeakRaw);

    if (point == 0) { posPeakOffset = posPeakRaw / 4095.0 * (ADC_VREF / 1000.0); negPeakOffset = negPeakRaw / 4095.0 * (ADC_VREF / 1000.0); EEPROM.put(12, posPeakOffset); EEPROM.put(16, negPeakOffset); } }

    void loadCalibrationFromEEPROM() { EEPROM.get(0, rmsOffset0); EEPROM.get(4, rmsOffset1); EEPROM.get(8, rmsOffset2); EEPROM.get(12, posPeakOffset); EEPROM.get(16, negPeakOffset); calibrationChan0Complete = (rmsOffset0 != 0); calibrationChan1Complete = (rmsOffset1 != 0); calibrationChan2Complete = (rmsOffset2 != 0); }

    void loadArrayFromEEPROM(float* array, int eepromBase) { for (uint8_t i = 0; i < CAL_POINTS; i++) { EEPROM.get(eepromBase + i * sizeof(float), array[i]); } }

    void printCalibrationData() { float tempArray[CAL_POINTS];

    Serial.println(F("RMS0 (Gain 100):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS0ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS0Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("RMS1 (Gain 1):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS1ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS1Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("RMS2 (Gain 10):")); loadArrayFromEEPROM(tempArray, EEPROM_RMS2ADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vrms=")); Serial.print(pgm_read_float(&calRMS2Values[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("Positive Peak (Channel 3):")); loadArrayFromEEPROM(tempArray, EEPROM_POSPEAKADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vpp=")); Serial.print(pgm_read_float(&calPPValues[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); }

    Serial.println(F("Negative Peak (Channel 4):")); loadArrayFromEEPROM(tempArray, EEPROM_NEGPEAKADC); for (uint8_t i = 0; i < CAL_POINTS; i++) { Serial.print(F("Point ")); Serial.print(i); Serial.print(F(": Vpp=")); Serial.print(pgm_read_float(&calPPValues[i]), 4); Serial.print(F(" V, ADC=")); Serial.println(tempArray[i]); } }

    float getCorrectedRMS(float adcReading, float* calADC, const float* calValues, float offset) { float value = interpolate(adcReading, calADC, calValues); return max(0, value - offset); }

    float interpolate(float adcReading, float* calADC, const float* calValues) { if (adcReading <= calADC[0]) return pgm_read_float(&calValues[0]); if (adcReading >= calADC[CAL_POINTS - 1]) return pgm_read_float(&calValues[CAL_POINTS - 1]); for (uint8_t i = 0; i < CAL_POINTS - 1; i++) { if (adcReading >= calADC[i] && adcReading <= calADC[i + 1]) { float slope = (pgm_read_float(&calValues[i + 1]) - pgm_read_float(&calValues[i])) / (calADC[i + 1] - calADC[i]); return pgm_read_float(&calValues[i]) + slope * (adcReading - calADC[i]); } } return pgm_read_float(&calValues[CAL_POINTS - 1]); }

    void handleSerialCommand() { if (Serial.available()) { String command = Serial.readStringUntil('\n'); command.trim(); while (Serial.available()) Serial.read(); // Clear remaining buffer if (command == "C0") { currentMode = CAL_CHAN0; Serial.println(F("Entering Channel 0 Calibration")); } else if (command == "C1") { currentMode = CAL_CHAN1; Serial.println(F("Entering Channel 1 Calibration")); } else if (command == "C2") { currentMode = CAL_CHAN2; Serial.println(F("Entering Channel 2 Calibration")); } else if (command == "CP") { currentMode = CAL_PEAK; Serial.println(F("Entering Peak-to-Peak Calibration")); } else if (command == "CAL") { Serial.println(F("Displaying EEPROM Calibration Data:")); printCalibrationData(); } else if (command == "0" || command == "1" || command == "2" || command == "3") { setAttenuation(command.toInt() * 10); Serial.print(F("Set attenuation to: ")); Serial.println(ATTENUATION_STEPS[currentAttenuationIndex]); } else if (command.toInt() > 0) { currentStep = findStep(command.toInt()); updateVariableResistance(); Serial.print(F("Set load to: ")); Serial.println(pgm_read_word(&resistanceSteps[currentStep])); } else { Serial.println(F("Unknown command")); } } }

    void resetPeaks() { digitalWrite(PEAK_RESET_PIN, HIGH); delayMicroseconds(20); digitalWrite(PEAK_RESET_PIN, LOW); }

    void setAttenuation(uint8_t db) { sr.setNoUpdate(10, db == 0 ? HIGH : db == 10 ? LOW : db == 30 ? LOW : HIGH); sr.setNoUpdate(11, db == 0 ? HIGH : db == 20 ? LOW : db == 30 ? LOW : HIGH); sr.updateRegisters(); currentAttenuationIndex = (db == 0 ? 0 : db == 10 ? 1 : db == 20 ? 2 : 3); attenuationFactor = pow(10, db / 20.0); }

    void updateVariableResistance() { int targetResistance = pgm_read_word(&resistanceSteps[currentStep]); for (uint8_t i = 0; i < 10; i++) sr.setNoUpdate(i, HIGH); struct ResistorPin { int value; uint8_t pin; }; const ResistorPin resistors[] = {{2000, 5}, {1600, 4}, {800, 3}, {400, 2}, {200, 1}, {100, 0}, {50, 8}, {15, 7}, {10, 9}}; int remainingResistance = targetResistance; for (const ResistorPin& rp : resistors) { if (remainingResistance >= rp.value) { sr.setNoUpdate(rp.pin, LOW); remainingResistance -= rp.value; } } sr.setNoUpdate(6, HIGH); sr.updateRegisters(); }

    int findStep(int targetResistance) { for (int i = 0; i < numSteps; i++) { if (pgm_read_word(&resistanceSteps[i]) <= targetResistance) return i; } return numSteps - 1; }

  4. Meta Assistant

    To convert your Arduino Uno code to ESP32, you'll need to make some changes. Here's a step-by-step guide:

    1. Update the SPI library

    The ESP32 has a built-in SPI library, but it's not compatible with the Arduino SPI library. You'll need to use the esp_spi library instead.

    2. Update the pin definitions

    The ESP32 has different pin numbers than the Arduino Uno. You'll need to update the pin definitions for the SPI pins, the 74HC595 pins, and the peak reset pin.

    3. Update the EEPROM library

    The ESP32 doesn't have an EEPROM like the Arduino Uno. Instead, you can use the Preferences library to store data.

    4. Update the serial communication

    The ESP32 has a different serial communication library than the Arduino Uno. You can use the Serial library, but you'll need to configure it differently.

    Here's the updated code:

    #include <SPI.h>
    #include <Mcp320x.h>
    #include <ShiftRegister74HC595.h>
    #include <Preferences.h>
    
    // Pin definitions FOR 74HC595 USING SHIFTGRGISTER74HC595.H LIBRARY
    #define PEAK_RESET_PIN 25
    #define SR_DATA_PIN 23
    #define SR_CLK_PIN 18
    #define SR_LATCH_PIN 19
    
    //CS PIN FOR MC320X
    #define CS_PIN 5
    
    // SPI settings
    #define ADC_VREF 5000  // Reference voltage in mV
    #define ADC_CLK 1600000  // SPI clock speed in Hz
    #define SATURATION_THRESHOLD 3500  // Adjusted based on data
    
    // Resistance steps in PROGMEM (64 steps)
    const int resistanceSteps[] = {
      5175, 5000, 4800, 4600, 4400, 4200, 4000, 3800, 3600, 3400, 3200, 3000, 2800, 2600, 2400, 2200,
      2000, 1900, 1800, 1700, 1600, 1500, 1400, 1300, 1200, 1100, 1000, 900, 800, 700, 600, 500,
      475, 450, 425, 400, 375, 350, 325, 300, 275, 250, 225, 200, 175, 150, 125, 100,
      90, 80, 70, 60, 50, 40, 30, 20, 15, 12, 10, 8, 6, 4, 2, 1
    };
    const int numSteps = sizeof(resistanceSteps) / sizeof(resistanceSteps[0]);
    int currentStep = 0;
    
    // Attenuation settings
    const int ATTENUATION_STEPS[] = {0, 10, 20, 30};
    uint8_t currentAttenuationIndex = 0;
    float attenuationFactor = 1.0;
    
    // Measurement variables
    float V_shunt_RMS = 0.0;
    float emaRMS = 0.0;
    float emaPosPeak = 0.0;
    float emaNegPeak = 0.0;
    uint16_t rawRMS0 = 0, rawRMS1 = 0, rawRMS2 = 0;
    uint16_t rawPosPeak = 0, rawNegPeak = 0;
    const float ALPHA = 0.3;
    float rmsVoltage = 0.0;
    float posPeak = 0.0;
    float negPeak = 0.0;
    float current = 0.0;
    float power = 0.0;
    float crestFactor = 0.0;
    float peakToPeak = 0.0;
    uint8_t activeChannel = 1;
    float V_cal_RMS = 0.0;
    float V_cal_posPeak = 0.0;
    float V_cal_negPeak = 0.0;
    
    // Calibration variables
    const int CAL_POINTS = 10;
    float rmsOffset0 = 0.0, rmsOffset1 = 0.0, rmsOffset2 = 0.0;
    float posPeakOffset = 0.0, negPeakOffset = 0.0;
    const float calRMS0Values[CAL_POINTS] = {0.0, 0.00354, 0.01061, 0.01768, 0.03536, 0.07071, 0.10607, 0.14142, 0.17678, 0.21213};  // Gain 100, 0 to 0.60 Vpp
    const float calRMS1Values[CAL_POINTS] = {0.0, 0.28284, 0.56568, 0.84853, 1.13137, 1.41421, 1.69706, 1.97990, 2.26274, 2.82843};  // Gain 1, 0 to 8 Vpp
    const float calRMS2Values[CAL_POINTS] = {0.0, 0.07071, 0.14142, 0.21213, 0.28284, 0.35355, 0.42426, 0.49497, 0.56568, 0.63640};  // Gain 10, 0 to 1.8 Vpp
    const float calPPValues[CAL_POINTS] = {0.0, 0.5, 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0};  // Peak-to-Peak, max 8 Vpp
    bool calibrationChan0Complete = false;
    bool calibrationChan1Complete = false;
    bool calibrationChan2Complete = false;
    
    // Preferences
    Preferences preferences;
    
    // Objects
    MCP3208 adc(ADC_VREF, CS_PIN);
    ShiftRegister74HC595 sr(2, SR_DATA_PIN, SR_CLK_PIN, SR_LATCH_PIN);
    
    void setup() {
      pinMode(PEAK_RESET_PIN, OUTPUT);
      Serial.begin(115200);
      SPI.begin();
      SPI.setClockDivider(SPI_CLOCK_DIV4);
      loadCalibrationFromPreferences();
      updateVariableResistance();
      setAttenuation(0);
      Serial.println(F("QA-ES Initialized"));
    }
    
    void loop() {
      unsigned long currentMillis = millis();
      switch (currentMode) {
        case MANUAL: runManualMeasurement(currentMillis); break;
        case CAL_CHAN0: runCalibrationChan0(currentMillis); break;
        case CAL_CHAN1: runCalibrationChan1(currentMillis); break;
        case CAL_CHAN2: runCalibrationChan2(currentMillis); break;
        case CAL_PEAK: runCalibrationPeak(currentMillis); break;
      }
      if (Serial.available()) handleSerialCommand();
    }
    
    void takeMeasurement() {
      // ... (rest of the code remains the same)
    }
    
    void loadCalibrationFromPreferences() {
      preferences.begin("calibration", false);
      rmsOffset0 = preferences.getFloat("rmsOffset0", 0.0);
      rmsOffset1 = preferences.getFloat("rmsOffset1", 0.0);
      rmsOffset2 = preferences.getFloat("rmsOffset2", 0.0);
      posPeakOffset = preferences.getFloat("posPeakOffset", 0.0);
      negPeakOffset = preferences.getFloat("negPeakOffset", 0.0);
      calibrationChan0Complete = (rmsOffset0 != 0);
      calibrationChan1Complete = (rmsOffset1 != 0);
      calibrationChan2Complete = (rmsOffset2 != 0);
      preferences.end();
    }
    
    void saveCalibrationToPreferences() {
      preferences.begin("calibration", false);
      preferences.putFloat("rmsOffset0", rmsOffset0);
      preferences.putFloat("rmsOffset1", rmsOffset1);
      preferences.putFloat("rmsOffset2", rmsOffset2);
      preferences.putFloat("posPeakOffset", posPeakOffset);
      preferences.putFloat("negPeakOffset", negPeakOffset);
      preferences.end();
    }
    
    void handleSerialCommand() {
      // ... (rest of the code remains the same)
    }
    

    Note that you'll need to update the calibratePoint and calibratePeakPoint functions to use the Preferences library instead of EEPROM.

    Also, make sure to install the esp_spi library and the Preferences library in your ESP32 project. You can do this by going to Sketch > Include Library > Manage Libraries and searching for the libraries.

  5. User

    you did not clearly explain to connect which pin to whic pin like in arduino uno spi pins 11,12,13 connected to mcp320x, and shift register uses its library and non spi pins like 3,4,5.now guide me which pin to use in esp32 to which pin hardare

  6. Meta Assistant

    Here's a step-by-step guide to connect your hardware to the ESP32:

    MCP3208 SPI Connection

    The ESP32 has multiple SPI buses, but we'll use the default SPI bus (VSPI) for this example. The VSPI bus has the following pins:

    • SCK (Clock): GPIO18
    • MOSI (Master Out Slave In): GPIO23
    • MISO (Master In Slave Out): GPIO19
    • CS (Chip Select): Any GPIO pin (we'll use GPIO5)

    Connect your MCP3208 to the ESP32 as follows:

    • MCP3208 SCK (Clock) -> ESP32 GPIO18
    • MCP3208 MOSI (not used, as MCP3208 is a slave)
    • MCP3208 MISO -> ESP32 GPIO19
    • MCP3208 CS -> ESP32 GPIO5

    Shift Register 74HC595 Connection

    The Shift Register 74HC595 library uses the following pins:

    • Data: Any GPIO pin (we'll use GPIO17)
    • Clock: Any GPIO pin (we'll use GPIO16)
    • Latch: Any GPIO pin (we'll use GPIO4)

    Connect your 74HC595 to the ESP32 as follows:

    • 74HC595 SCK (Clock) -> ESP32 GPIO16
    • 74HC595 MOSI (Data) -> ESP32 GPIO17
    • 74HC595 RCK (Latch) -> ESP32 GPIO4

    Peak Reset Pin

    The peak reset pin can be connected to any GPIO pin (we'll use GPIO2).

    • Peak Reset -> ESP32 GPIO2

    Updated Code

    In your code, update the pin definitions as follows:

    // Pin definitions FOR 74HC595 USING SHIFTGRGISTER74HC595.H LIBRARY
    #define PEAK_RESET_PIN 2
    #define SR_DATA_PIN 17
    #define SR_CLK_PIN 16
    #define SR_LATCH_PIN 4
    
    //CS PIN FOR MC320X
    #define CS_PIN 5
    

    SPI Settings

    In your code, update the SPI settings as follows:

    void setup() {
      // ...
      SPI.begin(18, 19, 23, 5); // SCK, MISO, MOSI, CS
      SPI.setClockDivider(SPI_CLOCK_DIV4);
      // ...
    }
    

    Note that the SPI.begin() function takes four arguments: SCK, MISO, MOSI, and CS. In this case, we're using GPIO18 for SCK, GPIO19 for MISO, GPIO23 for MOSI, and GPIO5 for CS.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.