How does a LiDAR see a whole 3d outlook? Since it's spinning atop the waymo 360degrees,…
- User
How does a LiDAR see a whole 3d outlook? Since it's spinning atop the waymo 360degrees, wouldnt it just see a 1 pixel tall representation of depth all around it?
- Assistant
Think of an automotive LiDAR as a super-fast laser tape-measure that is swept across the scene in a very specific pattern.
The trick is that it’s NOT just “one laser spinning in a flat plane.”
Here’s how the common spinning (a.k.a. “mechanical”) units such as the old Waymo/Velodyne puck actually create a full 3-D point cloud:────────────────────────────────────────────
- Multiple lasers, each tilted a bit ──────────────────────────────────────────── top view (cut-away) side view ┌─────────────────────────┐ vertical fan of rays │ │ / +10° (high) │ rotating head │ / +8° 🔴🔴🔴🔴🔴🔴🔴🔴 stacked emitters … │ ← 64 (or 32, 16, …) lasers │ │ | 0° └─────────────────────────┘ \ −15° 〳 −25° (low curb)
• Every “channel” (laser + receiver pair) is fixed at its own elevation angle.
• Typical specs:
– 16-channel lidar ⇒ ≈ −15 ° to +15 ° vertical FOV
– 64-channel lidar ⇒ as much as −25 ° to +10 °, 0.4 ° vertical spacing
– Firing rate ≈ 10–20 k laser shots per channel per second.So, at any instant the lidar is drawing a 64-pixel-tall ring of distance measurements.
──────────────────────────────────────────── 2. Continuous 360° spin gives you the other axis ──────────────────────────────────────────── While those 64 (or 32, …) beams form a vertical “fan,” the whole assembly spins 5 – 20 times each second.
As it rotates, each beam paints out a little dotted circle at its elevation angle. Put all those circles together and you get a dense cylindrical shell of points around the car.one full rotation → 3-D point cloud (simplified) ┌───────────────┐ │ * * * │ ← high-angle beam │ * * * * │ │* * o * * │ │ * * * * │ │ * * * │ ← low-angle beam └───────────────┘• At 10 Hz (100 ms per spin) a 64-channel unit can deliver ≈ 1.2 million points per frame.
• Because everything is captured in < 100 ms, motion blur is small for normal driving speeds (and can be corrected with IMU data).──────────────────────────────────────────── 3. How the 3-D coordinates appear ────────────────────────────────────────────
- Measure time-of-flight t of each laser pulse.
- Convert to distance d = (c · t)/2.
- Knowing the laser’s azimuth (rotation angle) and elevation angle, convert (d, az, el) ⟶ (x, y, z).
- Stitch all points from one rotation into a “point cloud” frame; stitch many frames over time for a map.
──────────────────────────────────────────── 4. What if you really only had ONE beam? ──────────────────────────────────────────── • You’d get exactly the “1-pixel-tall” ring you imagined—just a 2-D lidar.
• Robots often mount such 2-D lidars close to the ground (e.g., indoor Roombas or warehouse AGVs).
• To build 3-D with a single beam you must move the sensor up/down or let the vehicle’s own motion sweep the beam through space (called “push-broom” scanning). It’s slower and less dense, which is why self-driving cars prefer multi-beam designs.──────────────────────────────────────────── 5. Other modern approaches (bonus) ──────────────────────────────────────────── • MEMS or “image lidar”: one laser, one detector, two tiny mirrors do a raster scan (like an old CRT).
• Flash lidar: flood-illuminate the whole scene and use a 2-D detector array—no moving parts, but currently shorter range.
• FMCW coherent lidar: sweeps laser frequency to get both distance and direct radial velocity (like radar Doppler). Still experimental.──────────────────────────────────────────── Key takeaway ──────────────────────────────────────────── Spinning lidars use a stack of lasers (vertical resolution) + rotation (horizontal resolution) + rapid firing (dense sampling) to create a rich 3-D point cloud, not just a single ring of depths.
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.