Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen3-235b-a22b· Alibaba (Qwen)Hugging Face LMArena Human Preference 140K

Hello, I have a schematic I want you to analyze. It a VCC=60V connected to a resistor…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Geminigemini-2.5-flash-lite-preview-06-17-thinking’s answer.
  1. User

    Hello, I have a schematic I want you to analyze. It a VCC=60V connected to a resistor divider of 100k 100k. In parrallele of one of the resistor there is a zener diode of 3V3. Draw in asci the schematic

  2. Qwen Assistant

    Here’s the ASCII schematic and analysis of your circuit:

    VCC (60V)
       |
       |
     [100kΩ] (R1)
       |
       +-----> Vout (3.3V?)
       |
     [100kΩ] (R2)
       |
      === [Zener Diode 3V3] (D1)
       |
      GND
    

    Circuit Analysis

    1. Resistor Divider Basics

      • Without the Zener diode, the resistor divider would output Vout=60V2=30VV_{out} = \frac{60V}{2} = 30V (since R1=R2=100kΩR1 = R2 = 100k\Omega).
    2. Effect of the Zener Diode

      • The 3.3V Zener diode (D1) is placed in parallel with R2 (lower resistor). This clamps VoutV_{out} to 3.3V, overriding the resistor divider's natural 30V output.
      • For a Zener to regulate, it requires a minimum reverse current (IZ(min)I_{Z(min)}). Typical Zeners need IZ≥1mAI_Z \geq 1mA for stable regulation.
    3. Current Calculations

      • Voltage across R1: VR1=60V−3.3V=56.7VV_{R1} = 60V - 3.3V = 56.7V.
      • Current through R1: IR1=56.7V100kΩ=0.567mAI_{R1} = \frac{56.7V}{100k\Omega} = 0.567mA.
      • Current through R2: IR2=3.3V100kΩ=0.033mAI_{R2} = \frac{3.3V}{100k\Omega} = 0.033mA.
      • Zener current: IZ=IR1−IR2=0.567mA−0.033mA=0.534mAI_Z = I_{R1} - I_{R2} = 0.567mA - 0.033mA = 0.534mA.
    4. Key Issue

      • The Zener current (IZ=0.534mAI_Z = 0.534mA) is below the minimum required for regulation (typically ≥1mA\geq 1mA).
      • Result: The Zener may not regulate properly, and VoutV_{out} will likely be less than 3.3V or unstable.
    5. Power Dissipation

      • Zener power: PZ=3.3V×0.534mA≈1.76mWP_Z = 3.3V \times 0.534mA \approx 1.76mW.
      • Most Zeners require PZ≥200mWP_Z \geq 200mW for nominal regulation. This circuit operates far below that threshold.

    Conclusion

    • The circuit does not work as intended because the Zener diode lacks sufficient current to regulate the voltage.
    • Solutions:
      • Reduce resistor values (e.g., use 1kΩ1k\Omega resistors instead of 100kΩ100k\Omega) to increase current.
      • Use a Zener with a lower IZ(min)I_{Z(min)} rating.
      • Add a series resistor for the Zener to isolate it from the divider.

    Let me know if you want to refine the design!

  3. User

    What would be the condition to break the zener ? If the resistor were 1 ohm and 1 ohm what would it impli ?

  4. Qwen Assistant

    Let’s analyze both questions in detail:


    1. Conditions to Break the Zener Diode

    A Zener diode fails when:

    • Exceeds its maximum power rating: PZ(max)=VZ×IZ(max)P_{Z(max)} = V_Z \times I_{Z(max)}.
      Example: A 3.3V Zener with PZ(max)=400mWP_{Z(max)} = 400mW can only handle IZ(max)≈120mAI_{Z(max)} \approx 120mA.
    • Exceeds its maximum current rating: Even if power is within limits, physical damage can occur if IZ(max)I_{Z(max)} is too high.
    • Thermal overload: Sustained power dissipation beyond heatsinking capabilities causes overheating.

    In your original circuit, the Zener current was 0.534mA (too low for regulation). To break the Zener, you’d need to force an extremely high current (e.g., by reducing series resistance drastically).


    2. If Resistors Were 1Ω and 1Ω

    If R1 = R2 = 1Ω (instead of 100kΩ), the circuit becomes catastrophic:

    Schematic

    VCC (60V)
       |
     [1Ω] (R1)
       |
       +-----> Vout (3.3V?) (CLAMPED BY ZENER)
       |
     [1Ω] (R2)
       |
      === [Zener 3V3] (D1)
       |
      GND
    

    Calculations

    1. Voltage across R1:
      VR1=60V−3.3V=56.7VV_{R1} = 60V - 3.3V = 56.7V.
    2. Current through R1:
      IR1=56.7V1Ω=56.7AI_{R1} = \frac{56.7V}{1Ω} = 56.7A (EXTREMELY HIGH!).
    3. Current through R2:
      IR2=3.3V1Ω=3.3AI_{R2} = \frac{3.3V}{1Ω} = 3.3A.
    4. Zener current:
      IZ=IR1−IR2=56.7A−3.3A=53.4AI_Z = I_{R1} - I_{R2} = 56.7A - 3.3A = 53.4A.
    5. Power dissipation:
      • Zener: PZ=3.3V×53.4A=176WP_Z = 3.3V \times 53.4A = 176W (destroys any standard Zener).
      • R1: PR1=IR12×R1=(56.7A)2×1Ω≈3,215WP_{R1} = I_{R1}^2 \times R1 = (56.7A)^2 \times 1Ω \approx 3,215W.
      • R2: PR2=(3.3A)2×1Ω=10.9WP_{R2} = (3.3A)^2 \times 1Ω = 10.9W.

    Consequences

    • Zener Diode: Instantly vaporizes due to 176W dissipation (typical Zeners max out at 400mW–1W).
    • Resistors:
      • R1 would melt or explode (3kW is industrial-grade power).
      • R2 would overheat (10.9W exceeds typical resistor ratings).
    • Wiring: Likely to catch fire due to extreme current (56.7A is equivalent to a car battery short).

    Conclusion

    • Zener Failure: Occurs if IZ>IZ(max)I_Z > I_{Z(max)} or PZ>PZ(max)P_Z > P_{Z(max)}.
    • 1Ω Resistors: Create a near-short circuit, causing:
      • 53.4A through the Zener (destroys it instantly).
      • 3kW dissipation in R1 (destroys resistors and wiring).

    This configuration is extremely dangerous and would result in immediate component failure, sparks, or fire. Always ensure resistor values limit current to safe levels for the Zener and resistors.

  5. User

    Same power analysis with 100k and 100k

  6. Qwen Assistant

    Power Analysis for Original Circuit (100kΩ + 100kΩ Resistors)

    Let’s calculate the power dissipated by each component in the original circuit:

    Circuit Setup

    VCC (60V)  
       |  
     [100kΩ] (R1)  
       |  
       +-----> Vout (CLAMPED to 3.3V by Zener D1)  
       |  
     [100kΩ] (R2)  
       |  
      === [Zener Diode 3V3] (D1)  
       |  
      GND  
    

    1. Power Dissipated by Resistor R1

    • Voltage across R1:
      VR1=VCC−VZ=60V−3.3V=56.7VV_{R1} = V_{CC} - V_{Z} = 60V - 3.3V = 56.7V
    • Current through R1:
      IR1=VR1R1=56.7V100kΩ=0.567mAI_{R1} = \frac{V_{R1}}{R1} = \frac{56.7V}{100k\Omega} = 0.567mA
    • Power in R1:
      PR1=VR1×IR1=56.7V×0.567mA=32.1mWP_{R1} = V_{R1} \times I_{R1} = 56.7V \times 0.567mA = 32.1mW

    Conclusion: Safe (standard 1/4W resistor can handle 250mW).


    2. Power Dissipated by Resistor R2

    • Voltage across R2:
      VR2=VZ=3.3VV_{R2} = V_Z = 3.3V
    • Current through R2:
      IR2=VR2R2=3.3V100kΩ=0.033mAI_{R2} = \frac{V_{R2}}{R2} = \frac{3.3V}{100k\Omega} = 0.033mA
    • Power in R2:
      PR2=VR2×IR2=3.3V×0.033mA=0.109mWP_{R2} = V_{R2} \times I_{R2} = 3.3V \times 0.033mA = 0.109mW

    Conclusion: Negligible power dissipation (safe).


    3. Power Dissipated by Zener Diode D1

    • Zener Current:
      IZ=IR1−IR2=0.567mA−0.033mA=0.534mAI_Z = I_{R1} - I_{R2} = 0.567mA - 0.033mA = 0.534mA
    • Power in Zener:
      PZ=VZ×IZ=3.3V×0.534mA=1.76mWP_Z = V_Z \times I_Z = 3.3V \times 0.534mA = 1.76mW

    Conclusion:

    • The Zener diode is dissipating 1.76mW, which is far below its minimum regulation current (typically IZ(min)≥1mAI_{Z(min)} \geq 1mA for small Zeners).
    • The Zener will not regulate properly and may not even conduct fully.

    4. Total Power Dissipated in the Circuit

    • Total Power:
      Ptotal=PR1+PR2+PZ=32.1mW+0.109mW+1.76mW=33.97mWP_{total} = P_{R1} + P_{R2} + P_Z = 32.1mW + 0.109mW + 1.76mW = 33.97mW

    Conclusion:

    • The circuit consumes ~34mW from the 60V supply.
    • All components are within safe power limits, but the Zener fails to regulate due to insufficient current.

    Key Takeaways

    1. Resistors: Both R1 and R2 are safe (power dissipation << max ratings).
    2. Zener Diode:
      • Fails to regulate because IZ=0.534mA<IZ(min)I_Z = 0.534mA < I_{Z(min)}.
      • Power dissipation is too low for stable operation.
    3. Functional Failure:
      • The output voltage will not stabilize at 3.3V.
      • The Zener acts more like a small leakage path than a regulator.

    What Needs to Change?

    To make the Zener regulate properly:

    1. Reduce resistor values (e.g., use 1kΩ instead of 100kΩ) to increase current.
    2. Add a series resistor for the Zener to isolate it from the divider.
    3. Use a lower-power Zener (e.g., a 100mW Zener designed for low currents).

    Let me know if you want to redesign the circuit!

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.