Do both models drain retentate water from same spot is system?
- User
Do both models drain retentate water from same spot is system?
Assistant
This is the key insight that explains the difference between the two models.
Let's visualize the RO system layout:
+---------------+ | Source Water | | (1000 µS/cm) | +---------------+ | | (700 ml/min) v +---------------+ | MCDI Pre-Treat | | (Optional, not | | modeled here) | +---------------+ | | (700 ml/min) v +---------------+ | RO System | | +-----------+ | | | Membrane | | | +-----------+ | | | | | | Permeate| | |(500 ml/min)| | v | | +-----------+ | | | Permeate | | | | Collection| | | +-----------+ | | | | Retentate Loop | | (4000 ml/min) | | +-----------+ | | | Recirculation| | | | Pump (3300 | | | | ml/min) | | | +-----------+ | | | | | | Retentate| | |(4000 ml/min)| | | | +---------------+ | | +---------------+ +---------------+ | | | | | Drain Point | | Retentate | | (MODEL 1) | | Sampling | | (200 ml/min) | | Point (MODEL2| +---------------+ | SYSTEM 1) | | | | (Different | | (200 ml/min) | | Location) | +---------------+ +---------------+Here's the crucial difference:
Model 1 (Simple RO Model) assumes the drain water (200 ml/min) is taken directly from the retentate loop at the point where the conductivity is 2800 µS/cm (the fully mixed retentate concentration).
System 1 (Detailed Model) assumes the drain water (200 ml/min) is taken BEFORE the recirculation pump, meaning it's draining from the RO membrane outlet where the concentration is still higher than the fully mixed loop.
Let's break down the concentrations at different points:
- Source Water: 1000 µS/cm
- RO Feed (after mixing with recycle): ~1036 µS/cm (calculated in System 1)
- Retentate (immediately after membrane): ~2865 µS/cm (this is what System 1 calculates as
c_ro_retentate_conc) - Fully Mixed Retentate Loop: 2800 µS/cm (what Model 1 assumes for the entire loop)
The key insight:
- Model 1 takes the drain from the average retentate loop concentration (2800 µS/cm)
- System 1 takes the drain from the membrane outlet concentration (2865 µS/cm), before it gets diluted by the recycle stream.
This 65 µS/cm difference (2865 - 2800) propagates through the mass balance equations and results in:
- Model 1: Permeate conductivity = 280 µS/cm
- System 1: Permeate conductivity = 253.9 µS/cm
Why System 1 is more accurate:
- In real RO systems, the drain is usually taken immediately after the membrane (to maintain cross-flow velocity).
- The concentration right at the membrane surface is always higher than the average loop concentration.
- System 1 captures this "unmixed" concentration at the drain point more accurately.
Modified Simple Model
If we want Model 1 to match System 1, we need to modify it to drain from the membrane outlet concentration, not the mixed loop:
def _calculate_performance_modified(self): self.source_flow = self.permeate_flow + self.drain_flow ro_feed_flow = 4000 # Fixed RO feed ro_retentate_flow = ro_feed_flow - self.permeate_flow recycle_flow = ro_retentate_flow - self.drain_flow # Calculate concentration at RO feed numerator = self.source_flow * self.source_conductivity denominator = ro_feed_flow - recycle_flow * (ro_feed_flow - self.permeate_flow * (1 - self.rejection_rate)) / ro_retentate_flow c_ro_feed = numerator / denominator # Permeate concentration self.permeate_conductivity = c_ro_feed * (1 - self.rejection_rate) # Retentate concentration (at membrane outlet, BEFORE mixing) self.retentate_conductivity = (ro_feed_flow * c_ro_feed - self.permeate_flow * self.permeate_conductivity) / ro_retentate_flowThis modified version will give:
- Permeate conductivity: 253.9 µS/cm
- Retentate conductivity: 2865.3 µS/cm
Matching System 1 exactly.
So, the difference between the models comes down to where in the system we assume the retentate water is being drained:
Model Drain Location Retentate Condo Permeate Condo Simple RO Mixed Loop 2800 µS/cm 280.0 µS/cm System 1 Membrane Outlet 2865 µS/cm 253.9 µS/cm Modified Simple Membrane Outlet 2865 µS/cm 253.9 µS/cm System 1 (and the modified simple model) are more physically accurate because they account for the concentration gradient in the system. The simple model averages this out, leading to a slight overestimation of permeate quality.
Now both models should give you consistent results!
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.