Consider this problem: A projectile is thrown up and passes point A, then point B a…
- User
Consider this problem:
A projectile is thrown up and passes point A, then point B a height h above A. Let TA and TB be the time intervals between the two times the projectile passes A and B, respectively. (a) Show that an experimentalist can measure g by computing g = 8h/(T_A^2 A − T_B^2 ). (b) This procedure probably looks a little contrived. Why is it better than doing something simpler, such as just dropping the ball and using ∆y = gt^2/2?
Assuming the answer to part (a), answer part (b).
- Assistant
Let's tackle this question systematically, beginning with part (a), followed by the conceptual reasoning for part (b).
Part (a): Derivation of ( g = \frac{8h}{T_A^2 - T_B^2} )
Let’s define the motion of the projectile:
- The object is thrown upwards.
- It passes point A twice: once on the way up and once on the way down.
- It passes point B, a distance ( h ) above point A, also twice.
Let:
- ( T_A ) = the total time between the two times the projectile passes point A.
- ( T_B ) = the total time between the two times the projectile passes point B, which is a distance ( h ) above A.
📌 Since the motion is symmetric, the projectile takes the same amount of time to rise to a given point as it does to fall back down past that point. So:
- At point A, the object passes it at time ( t_1 ) (on the way up) and again at time ( t_2 ) (on the way down), so: [ T_A = t_2 - t_1 ]
- Similarly, for point B (higher up, above A): [ T_B = t_4 - t_3 ] where ( t_3 ) and ( t_4 ) are the times the projectile passes point B.
Let’s now define the peak of the motion — the highest point — as time ( t = t_0 ). Since the projectile follows symmetric motion,
- The time passes equally long rising upward and falling downward from the apex to a given height.
- So, the two times it passes point A are symmetric about the apex: [ t_1 = t_0 - \Delta t_A, \quad t_2 = t_0 + \Delta t_A \Rightarrow T_A = 2\Delta t_A ]
- Similarly: [ t_3 = t_0 - \Delta t_B, \quad t_4 = t_0 + \Delta t_B \Rightarrow T_B = 2\Delta t_B ]
Let’s find the position equation to relate time to height:
Let the apex of the projectile (maximum height) be at ( y = 0 ), with downward positive direction (or flip sign later), the standard kinematic equation gives:
[ y = \frac{1}{2}g t^2 \Rightarrow t = \sqrt{\frac{2y}{g}} ]
So:
- Time to fall from apex to point A: ( \Delta t_A = \sqrt{\frac{2d_A}{g}} )
- Time to fall from apex to point B: ( \Delta t_B = \sqrt{\frac{2d_B}{g}} )
Since B is higher than A by height ( h ), we define:
[ d_A = h, \quad d_B = 0 \Rightarrow \Delta t_B = 0 \text{?} ]
Wait — we went wrong in reference level.
💡 Let's define the vertical position properly.
Set point A as the reference level ( y = 0 ), and point B at ( y = h ). Let the apex be at height ( H ) above point A.
On the way up: At apex: velocity is zero, ( v = 0 ), and the time from point A to the apex is ( t_A = \Delta t_A )
Using:
[ H = \frac{1}{2} g t_A^2, \quad \text{so } t_A = \sqrt{\frac{2H}{g}} ]
Similarly: From point B to apex: height = ( H - h )
[ t_B = \sqrt{\frac{2(H - h)}{g}} ]
So:
- Time between both passes through A is ( T_A = 2t_A = 2\sqrt{\frac{2H}{g}} )
- Time between both passes through B is ( T_B = 2t_B = 2\sqrt{\frac{2(H - h)}{g}} )
Now use both to eliminate ( H ):
[ T_A^2 = 4 \cdot \frac{2H}{g} = \frac{8H}{g}, \quad T_B^2 = 4 \cdot \frac{2(H - h)}{g} = \frac{8(H - h)}{g} ]
Subtract:
[ T_A^2 - T_B^2 = \frac{8H}{g} - \frac{8(H - h)}{g} = \frac{8H - 8(H - h)}{g} = \frac{8h}{g} ]
Solve for ( g ):
[ g = \frac{8h}{T_A^2 - T_B^2} ]
✔️ Q.E.D.
Part (b): Why is this method better than just dropping the ball and using ( \Delta y = \frac{1}{2} g t^2 ) ?
Let’s compare the two methods.
Drop Method:
- You drop a ball from a height ( h ), measure how long ( t ) it takes to hit the ground.
- Use:
[ g = \frac{2h}{t^2} ]
👉 Requires accurate timing of one event, and precise knowledge of initial height, and the first moment when ball was released.
But measuring the exact moment of release and impact is hard (reaction time errors, sensor delay, etc).
Two-Pass Method (derived above):
- Measure T_A and T_B — the time intervals between two passes at the same point.
- This is more robust:
- Uses symmetry: timing between passes, which can be captured via sensors (e.g., photogates) without requiring knowledge of the instant of release.
- Doesn't require knowing time of launch, just relative timings.
- Also doesn’t require knowing the total maximum height — just the known height difference ( h ) between points A and B.
In summary:
🔍 The two-pass method is better because:
- It avoids needing precise synchronization or detection of the exact instant of release and impact.
- It uses relative timing via symmetry — timing intervals, not absolute times.
- Can be measured more accurately using sensors (e.g., light gates) placed at A and B.
✅ Less susceptible to human error and more precise in practice.
Final Summary
(a) Showed that: [ g = \frac{8h}{T_A^2 - T_B^2} ]
(b) This method is better because it's based on:
- Timing differences between two symmetric events, which is more accurate,
- Doesn't require detecting the exact release point,
- Minimizes experimental error.
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.