Skip to content
TheChatArchiveThe Chat Archive
o3-2025-04-16· OpenAIHugging Face LMArena Human Preference 140K

synology nas DS920+ diskstation manager 7.2.2-72806 set up as NFSv4.1 but after reboot…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Qwenqwen3-235b-a22b-no-thinking’s answer.
  1. User

    synology nas DS920+ diskstation manager 7.2.2-72806 set up as NFSv4.1 but after reboot it goes back to NFSv3 , how to fix it

  2. Assistant

    Below is a small “check list” that usually solves the “DSM comes up in NFS v3 although I enabled v4.1” confusion, plus a way to hard-wire the version if you really want to turn v3 off for good.

    ──────────────────────────────────────── 1 Understand what you’re seeing ──────────────────────────────────────── • DSM can serve several NFS versions at the same time.
    Seeing a client mount with v3 (or tools such as showmount still working) does not necessarily mean DSM switched v4 off – it only means the client chose v3, or the tool never speaks v4 in the first place.

    • The authoritative place to look on the NAS is:
    cat /proc/fs/nfsd/versions
    Output example
    -2 -3 +4 +4.1 ← v4 / v4.1 active, v2/v3 inactive

    ──────────────────────────────────────── 2 Make the GUI change stick ──────────────────────────────────────── Control Panel → File Services → NFS

    ☑ Enable NFS service
    ▶ NFS v4 Support
    ☑ Enable NFS v4
    ☑ Enable NFS v4.1 (beta)

    Click “Apply”, then reboot once.
    After the reboot:

    cat /proc/fs/nfsd/versions
    

    should still show +4 +4.1.

    ⚠️ DSM 7.2.x quirk:
    If you tick ONLY “v4.1” but leave “Enable NFS v4” unticked, DSM sometimes forgets the setting on the next boot. Just leave both boxes ticked – you can still mount explicitly with vers=4.1 from the client.

    ──────────────────────────────────────── 3 (optional) Disable NFS v3 completely ──────────────────────────────────────── If you have no legacy clients and want to be 100 % sure v3 never comes back:

    SSH in as admin → sudo -i

    A) Persist the setting in the NFS config file

    cat > /etc/nfs.conf <<'EOF'
    [nfsd]
    vers2 = 0
    vers3 = 0
    vers4 = 1
    vers4.1 = 1
    udp   = 0
    EOF
    

    B) Restart the NFS service

    synoservice --restart nfs
    

    C) Verify

    cat /proc/fs/nfsd/versions
    # should show: -2 -3 +4 +4.1
    

    D) Keep it across every future boot / update
    Create /usr/local/etc/rc.d/01-force-nfsv41.sh:

    #!/bin/sh
    case "$1" in
      start)
        echo "+4 +4.1 -2 -3" > /proc/fs/nfsd/versions
        ;;
    esac
    exit 0
    
    chmod +x /usr/local/etc/rc.d/01-force-nfsv41.sh
    

    ──────────────────────────────────────── 4 Verify from a client ────────────────────────────────────────

    mount -t nfs4 -o vers=4.1,sec=sys nas:/volume1/share /mnt
    nfsstat -m     # Linux/BSD
    # look for vers=4.1
    

    Remember: showmount -e nas will always talk to the port-mapper (RPC v2/3) and thus fails or looks empty when you really disabled v3 – that is normal.

    ──────────────────────────────────────── 5 Still losing the setting? ──────────────────────────────────────── • Install the latest DSM 7.2.2 hot-fixes – Synology shipped a patch for a handful of models where the checkbox state was not written to disk.
    • If the problem persists after the above steps, open a ticket with Synology and reference your current build number (7.2.2-72806) – they can push a temporary HF (hot-fix) to correct the underlying database entry.

    That should keep your DS920+ firmly on NFS v4.1. Happy mounting!

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.