Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen3-235b-a22b-no-thinking· Alibaba (Qwen)Hugging Face LMArena Human Preference 140K

How can I replicate the Biefield Brown Effect at home? Give detailed instructions and a…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Claudeclaude-sonnet-4-20250514-thinking-32k’s answer.
  1. User

    How can I replicate the Biefield Brown Effect at home? Give detailed instructions and a supplies list.

  2. Qwen Assistant

    The Biefeld-Brown Effect (BBE) is an electrohydrodynamic (EHD) phenomenon where a high-voltage asymmetrical capacitor produces thrust due to ionized air movement. While it's often mistaken for anti-gravity, it's actually a result of ionic wind and momentum transfer in the surrounding air.

    This guide provides a detailed, step-by-step method to build a basic "lifter" that demonstrates the BBE at home using accessible materials — with a strong emphasis on safety, as this involves high voltage.


    ⚠️ Important Safety Warnings

    • High Voltage Risk: The setup operates at 20–30 kV DC, which can cause electric shocks, burns, or even heart fibrillation.
    • Never use mains power directly — always use isolated, battery-powered high-voltage sources.
    • Work in a well-ventilated area — ozone is produced during operation.
    • Use protective gear: Insulated gloves, eye protection, and keep one hand behind your back when testing.
    • Keep flammable materials away — sparks can ignite paper, fabric, etc.

    🧰 Supplies List

    🔌 High-Voltage Power Source (Battery-Powered)

    ItemPurposeNotes
    9V BatteryPower sourceCan be replaced with 12V battery for higher output
    Cockcroft-Walton Multiplier Kit or ComponentsSteps up voltage to ~20–30kVYou can buy pre-made kits or build from components:
    • 8x 1N4007 diodes
    • 8x 100pF 1kV ceramic capacitors
    • Perfboard, soldering iron, wire | | Alligator clips | Connect to lifter electrodes | Must be insulated | | Multimeter (optional) | Test voltage output | Use only if rated for high voltage |

    🛠️ Lifter Construction Materials

    ItemPurposeNotes
    Balsa wood sticks (1/8” x 1/8” x 18”)Frame structureLightweight and easy to cut/glue
    Aluminum foilBottom electrodeHeavy-duty preferred
    Magnet wire (30 AWG or finer)Top electrodeEnameled copper wire; must strip ends
    Glue gun & glue sticksAssemble frameHot glue works best for insulation
    Scissors / hobby knifeCut materialsBe careful handling sharp tools
    Sandpaper (fine grit)Strip enamel off magnet wireCritical for conductivity
    Clear tape or thread (optional)Secure foilFor extra support

    🏗️ Step-by-Step Instructions

    1. Build the Lifter Frame

    A. Construct the Triangle Frame

    • Cut three balsa sticks to 15–18 cm (6–7 inches).
    • Form a triangle by gluing the ends together.
    • Let dry thoroughly.

    B. Attach Top Electrode (Magnet Wire)

    • Cut a piece of magnet wire slightly longer than the top side of the triangle.
    • Stretch it tightly along the top edge.
    • Glue both ends to the corners.
    • Strip the enamel coating from both ends using sandpaper — this ensures electrical contact.

    C. Attach Bottom Electrode (Aluminum Foil)

    • Cut a long strip (~2 cm wide) of aluminum foil.
    • Wrap it around the bottom edge of the triangle.
    • Ensure it’s smooth and not touching the top wire.
    • Glue in place carefully.

    Important: There should be a gap of 2–4 cm between the top wire and bottom foil. No physical contact allowed!


    2. Build the High-Voltage Supply (Cockcroft-Walton Multiplier)

    You can either:

    • Buy a pre-built HV multiplier module (e.g., “Negative Ion Generator” modules on eBay/AliExpress), or
    • Build your own using the component list above.

    If building:

    • Solder diodes and capacitors in alternating series.
    • Input: 9V battery → Output: ~20–30kV DC (depending on number of stages).

    🔧 Tip: Watch YouTube tutorials like “How to Build a Cockcroft-Walton Multiplier” for visual help.


    3. Connect the Lifter to the Power Supply

    • Use insulated alligator clips:
      • Connect the positive terminal (output of multiplier) to the top wire.
      • Connect the negative terminal (ground) to the bottom foil.
    • Place the lifter on a non-conductive surface (e.g., plastic cup or glass jar) so it can lift freely.

    4. Test the Lifter

    • Turn on the high-voltage supply.
    • Observe:
      • A faint hissing sound (corona discharge).
      • A blue glow near the top wire (ionization).
      • The lifter may vibrate or lift slightly (1–5 cm is typical).

    🧪 Troubleshooting:

    • If no movement: check stripped wire ends, increase voltage, reduce weight.
    • If arcing: increase gap between electrodes.
    • If unstable: reinforce frame or adjust balance.

    ✅ Expected Observations

    • The device will rise slightly when powered.
    • Movement is away from the thin electrode (top wire), confirming the Biefeld-Brown effect.
    • Lift stops in a vacuum — proving it relies on air molecules.
    • Reversing polarity reduces or eliminates lift — the effect depends on direction of ion drift.

    📝 Final Notes

    • This experiment does not produce true anti-gravity — it uses ion wind to push against ambient air.
    • The effect is weak and cannot scale easily to large devices.
    • Always disconnect power before adjusting or touching any part of the lifter.
    • Never leave the setup unattended while powered.

    📚 Optional Enhancements

    • Add a fan or motor to stabilize the lifter mid-air.
    • Try different electrode shapes or materials (e.g., carbon fiber vs. foil).
    • Measure current/voltage with a high-voltage probe and oscilloscope.

    Would you like a diagram or circuit layout for the Cockcroft-Walton multiplier? Or a parts shopping list with links to recommended suppliers?

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.