Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen3-235b-a22b-no-thinking· Alibaba (Qwen)Hugging Face LMArena Human Preference 140K

I have installed proxmox OS on a baremetal machine. The OS is installed and running on a…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Kimikimi-k2-0711-preview’s answer.
  1. User

    I have installed proxmox OS on a baremetal machine. The OS is installed and running on a small M.2 SSD card. The motherboard is GA-Z170X-Gaming-3-rev-10, and the graphics card is an NVIDIA 1060 3gb. I have created a VM that is running Ubuntu server. I have successfully installed an internal HDD and then mounted that to the VM and can access and write to it via the VM's shell.

    I am struggling however to passthrough the graphics card. Can you help me please?

  2. Qwen Assistant

    Yes, I can help you pass through your NVIDIA GeForce GTX 1060 3GB GPU to a Proxmox VM. This is a common use case for people wanting to run Windows or Linux guests with direct access to a dedicated GPU (e.g., for gaming, virtual desktops, etc.).

    Here's a step-by-step guide tailored to your setup:


    ✅ PrEREQUISITES

    Before we begin:

    • Ensure IOMMU/VT-d is enabled in your BIOS.
    • Your CPU must support IOMMU (Intel VT-d). Since you're on a Z170 chipset (Skylake), it likely does.
    • You are using the VFIO driver, not the legacy nvidia or nouveau drivers for GPU passthrough.

    🔧 STEP 1: Enable IOMMU in BIOS

    1. Reboot into BIOS (usually by pressing Delete or F2 at boot).
    2. Look under Advanced > Chipset Settings or similar.
    3. Find and enable:
      • Intel Virtualization Technology (VT-x)
      • Intel VT-d (Virtualization Technology for Directed I/O)

    Save and exit.


    🐧 STEP 2: Enable IOMMU in Proxmox Kernel

    Edit GRUB config to enable IOMMU:

    nano /etc/default/grub
    

    Add the following to GRUB_CMDLINE_LINUX:

    intel_iommu=on iommu=pt
    

    Example line after edit:

    GRUB_CMDLINE_LINUX="quiet intel_iommu=on iommu=pt"
    

    Update GRUB:

    update-grub
    

    🛠️ STEP 3: Enable VFIO Kernel Module

    Ensure that the kernel uses vfio-pci instead of loading nouveau or nvidia drivers directly on the host.

    Create modprobe configuration:

    echo "options vfio-pci ids=10de:1c02,10de:10f0" > /etc/modprobe.d/vfio.conf
    

    Note: The above PCI IDs are for the NVIDIA GTX 1060 3GB. You can verify these later using lspci.

    Also create a blacklist for nouveau and nvidia:

    echo "blacklist nouveau" > /etc/modprobe.d/blacklist-nvidia.conf
    echo "blacklist nvidia" >> /etc/modprobe.d/blacklist-nvidia.conf
    

    Now update initramfs:

    update-initramfs -u
    

    🖥️ STEP 4: Identify GPU Device(s)

    Run:

    lspci | grep -i nvidia
    

    You should see something like:

    01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB] (rev a1)
    01:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1)
    

    Take note of the PCIe addresses (01:00.0 and 01:00.1).

    Then check if they are bound to vfio-pci:

    echo -n "0000:01:00.0" | sudo tee /sys/bus/pci/drivers/vfio-pci/bind
    echo -n "0000:01:00.1" | sudo tee /sys/bus/pci/drivers/vfio-pci/bind
    

    To automate this on boot:

    Install vfio-pci:

    apt install vfio-pci vfio-islnb4
    

    Then find the exact vendor IDs:

    lspci -nn | grep -i nvidia
    

    Output will be something like:

    01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB] [10de:1c02] (rev a1)
    01:00.1 Audio device [0403]: NVIDIA Corporation GP106 High Definition Audio Controller [10de:10f0] (rev a1)
    

    Use those IDs in /etc/modprobe.d/vfio.conf:

    options vfio-pci ids=10de:1c02,10de:10f0
    

    Then regenerate initramfs again:

    update-initramfs -u
    

    ⚙️ STEP 5: Configure the VM for GPU Passthrough

    Assuming your Ubuntu Server VM is already created, shut it down before editing its config.

    Edit VM config:

    qm edit <VMID>
    

    Add the following lines:

    hostpci0: 01:00.0,pcie=1,x-vga=1
    

    If you want to also passthrough the audio component:

    hostpci0: 01:00.0;01:00.1,pcie=1,x-vga=1
    

    Replace <VMID> with the actual ID of your Ubuntu VM.


    📦 STEP 6: Set Machine Type to Q35

    Make sure your VM uses the Q35 machine type (needed for PCIe):

    In the VM config:

    machine: q35
    

    Also ensure:

    cpu: EPYC  # or another modern CPU model that supports required features
    

    🔄 STEP 7: Boot the VM and Install GPU Drivers

    Start the VM:

    qm start <VMID>
    

    Once booted, install the appropriate NVIDIA drivers inside the guest OS.

    For Ubuntu:

    sudo apt update
    sudo apt install nvidia-driver-535
    

    Or download from https://www.nvidia.com/Download/index.aspx

    Reboot the guest after installation.


    🧪 OPTIONAL: Verify GPU Access in Guest

    Inside the VM:

    nvidia-smi
    

    If it shows the GTX 1060, then the GPU passthrough was successful!


    📌 TIPS & NOTES

    • If you're planning to passthrough this card for Windows gaming, consider using a Windows VM instead of Ubuntu.
    • Make sure the UEFI settings are correct if you're using OVMF firmware.
    • If you encounter issues with display output, try connecting a monitor directly to the GPU during boot.
    • Some users disable Secure Boot and Fast Boot in BIOS for better compatibility.

    ❓Still Having Issues?

    Let me know:

    • Output of lspci -v (especially around your GPU)
    • Whether you're using BIOS or UEFI for the VM
    • If you're trying to pass it to a Linux or Windows VM

    I’ll help you debug further.


    Would you like a script to automate some of this?

  3. User

    Can you add explanations as to why and what the purpose of each step is please

  4. Qwen Assistant

    Absolutely! Here's the same step-by-step guide, but with detailed explanations for each part. This will help you understand not just what to do, but why you're doing it and how everything fits together.


    🧠 GPU Passthrough Guide with Proxmox (Explained)

    This guide will walk you through how to pass through your NVIDIA GTX 1060 3GB graphics card to a Proxmox VM, and explain what each step does so you understand the process.


    ✅ PREREQUISITES

    What you need:

    • A GPU (in this case, NVIDIA GTX 1060 3GB)
    • A motherboard that supports IOMMU/VT-d (Intel) or AMD-Vi (AMD)
    • A CPU that supports virtualization (Intel VT-x and VT-d)
    • Proxmox VE installed on your system
    • A working VM (Ubuntu in your case)

    Why it's important:

    GPU passthrough allows a virtual machine (VM) to directly access and control the GPU, bypassing the host OS. This is essential for tasks like gaming, rendering, or machine learning inside a VM.


    🔧 STEP 1: Enable IOMMU in BIOS

    What to do:

    • Reboot your machine and enter BIOS (usually by pressing Delete or F2).
    • Enable:
      • Intel Virtualization Technology (VT-x)
      • Intel VT-d (IOMMU)

    Why?

    • VT-x allows the CPU to run virtual machines efficiently.
    • VT-d / IOMMU allows devices (like your GPU) to be directly assigned to a VM.
    • Without IOMMU enabled, PCIe device passthrough (like a GPU) won't work.

    🐧 STEP 2: Enable IOMMU in Proxmox Kernel

    What to do:

    Edit GRUB config:

    nano /etc/default/grub
    

    Add this to GRUB_CMDLINE_LINUX:

    intel_iommu=on iommu=pt
    

    Then run:

    update-grub
    

    Why?

    • This tells the Linux kernel to enable IOMMU support at boot.
    • iommu=pt enables IOMMU pass-through mode, which improves performance and compatibility with VFIO drivers.

    🛠️ STEP 3: Enable VFIO Kernel Module

    What to do:

    Create a config file:

    echo "options vfio-pci ids=10de:1c02,10de:10f0" > /etc/modprobe.d/vfio.conf
    

    Also create a blacklist:

    echo "blacklist nouveau" > /etc/modprobe.d/blacklist-nvidia.conf
    echo "blacklist nvidia" >> /etc/modprobe.d/blacklist-nvidia.conf
    

    Update the kernel modules:

    update-initramfs -u
    

    Why?

    • VFIO (Virtual Function I/O) is a driver that lets a VM directly access hardware like a GPU.
    • We're telling the kernel to use vfio-pci instead of the host drivers (nouveau or nvidia).
    • The ids=... line tells the kernel to bind the NVIDIA GPU to the vfio-pci driver.

    🖥️ STEP 4: Identify GPU Device(s)

    What to do:

    Run:

    lspci | grep -i nvidia
    

    You'll see something like:

    01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB] (rev a1)
    01:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1)
    

    Then check the IDs:

    lspci -nn | grep -i nvidia
    

    You'll see:

    01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB] [10de:1c02] (rev a1)
    01:00.1 Audio device [0403]: NVIDIA Corporation GP106 High Definition Audio Controller [10de:10f0] (rev a1)
    

    Why?

    • You need to know the PCIe address and vendor IDs to tell the kernel which devices to bind to vfio-pci.
    • 01:00.0 is the GPU, and 01:00.1 is the audio controller that comes with the GPU. You should passthrough both.

    ⚙️ STEP 5: Configure the VM for GPU Passthrough

    What to do:

    Shut down your VM first.

    Edit VM config:

    qm edit <VMID>
    

    Add:

    hostpci0: 01:00.0,pcie=1,x-vga=1
    

    Or if you want to passthrough both GPU and audio:

    hostpci0: 01:00.0;01:00.1,pcie=1,x-vga=1
    

    Why?

    • hostpci0 tells Proxmox to assign a host PCI device to the VM.
    • x-vga=1 tells QEMU that this is a VGA device, which is required for GPU passthrough.
    • pcie=1 ensures the device is passed through as a PCIe device, which is needed for modern GPUs.

    📦 STEP 6: Set Machine Type to Q35

    What to do:

    In the same VM config file, set:

    machine: q35
    

    Also ensure:

    cpu: EPYC
    

    Or another modern CPU model.

    Why?

    • The Q35 machine type supports PCIe devices and is recommended for GPU passthrough.
    • Older machine types like i440fx do not support PCIe properly.

    🔄 STEP 7: Boot the VM and Install GPU Drivers

    What to do:

    Start the VM:

    qm start <VMID>
    

    Inside the Ubuntu VM:

    sudo apt update
    sudo apt install nvidia-driver-535
    

    Or download from NVIDIA Driver Download

    Then reboot the VM.

    Why?

    • The guest OS needs the correct drivers to communicate with the GPU.
    • Even though the GPU is physically connected to the host, it's now "owned" by the VM, so the VM needs its own drivers.

    🧪 OPTIONAL: Verify GPU Access in Guest

    What to do:

    Inside the VM:

    nvidia-smi
    

    If you see the GTX 1060 listed, then GPU passthrough is working!

    Why?

    • nvidia-smi checks for NVIDIA GPUs and shows driver status.
    • If it works here, it means the VM is successfully using the GPU.

    📌 TIPS & NOTES

    • If you're using a Windows VM, install the Windows NVIDIA drivers from the official site.
    • You may need to connect a monitor to the GPU during boot to get display output.
    • Disable Secure Boot and Fast Boot in BIOS if you're having issues.
    • If you're using OVMF (UEFI), make sure it's properly configured.

    ❓Still Having Issues?

    Let me know:

    • Output of lspci -v (especially around your GPU)
    • Whether you're using BIOS or UEFI for the VM
    • If you're trying to pass it to a Linux or Windows VM

    I’ll help you debug further.


    Would you like a script version of this guide to automate some steps?

  5. User

    after step 7 I can no longer connect to the VM. I see 'Failed to connect to server' when I try in the proxmox vm concole

  6. Qwen Assistant

    That error — "Failed to connect to server" — when trying to access the VM console in Proxmox usually means one of two things:

    1. The VM is not running, or
    2. The VM is running, but the SPICE/VNC display server isn't working properly, especially after GPU passthrough.

    Since you mentioned this happened after Step 7 (booting the VM and installing NVIDIA drivers), it's very likely related to GPU passthrough interfering with the built-in QEMU display device, which is used by the Proxmox web console.


    🔍 Let’s Break Down What Happened

    When you pass through a real GPU (like your GTX 1060) to the VM:

    • The VM no longer uses the emulated graphics card (which is what the Proxmox web console uses via SPICE or VNC).
    • Instead, the VM tries to use the real GPU for display output.
    • If there's no monitor connected to that GPU, or if the GPU hasn’t initialized correctly, no graphical output will be available.
    • That’s why the Proxmox console can't connect — it's expecting a display server (VNC/SPICE), which is now gone or unresponsive.

    This is completely normal behavior when doing full GPU passthrough without keeping an emulated GPU for the console.


    ✅ SOLUTIONS & WORKAROUNDS

    Here are several options depending on how you want to manage the VM:


    ✅ OPTION 1: Use SSH to Access the VM (Recommended)

    You probably still have network connectivity, so just connect via SSH:

    ssh username@vm-ip-address
    

    If you don't know the IP address yet:

    1. Check the VM logs in Proxmox:

      qm monitor <VMID>
      

      Then type:

      info network
      
    2. Or check DHCP leases from your router.

    Once inside via SSH, you can verify:

    • Whether the VM is actually running
    • Whether the GPU is recognized (lspci, nvidia-smi if installed)
    • Whether there were any boot issues (dmesg, /var/log/Xorg.0.log if X is running)

    🔄 OPTION 2: Re-enable Emulated Display Temporarily

    If you need to use the Proxmox web console, you can temporarily add back an emulated GPU.

    Edit the VM config:

    qm edit <VMID>
    

    Add these lines:

    vga: qxl
    display: spice
    

    Also ensure:

    machine: q35
    

    Then restart the VM:

    qm stop <VMID>
    qm start <VMID>
    

    Now you should be able to reconnect via the Proxmox console again.

    ⚠️ Note: This may cause conflicts with your real GPU passthrough if not handled carefully. It's mostly useful for debugging.


    💡 OPTION 3: Connect a Monitor to the GPU

    If you're trying to run a GUI desktop (e.g., Ubuntu Desktop) in the VM and want to see the output:

    • Plug a monitor into the GTX 1060's HDMI or DisplayPort output
    • Reboot the VM
    • You should see the login screen or desktop appear

    This is how most people use GPU passthrough — they switch monitors between host and guest, or dedicate a second monitor to the VM.


    🧪 OPTION 4: Verify the VM is Actually Running

    Sometimes, the VM might crash or fail to boot after GPU passthrough due to driver issues.

    Check its status:

    qm status <VMID>
    

    Or view log messages:

    journalctl -u qemu-server@<VMID>.service
    

    Or inspect the VM's serial console:

    qm terminal <VMID>
    

    (Only works if serial console is configured in the VM OS)


    🛠️ BONUS: Configure Serial Console (for future troubleshooting)

    To avoid losing access altogether, set up a serial console in your VM:

    In VM config:

    qm edit <VMID>
    

    Add:

    serial0: socket
    

    Then in the VM's GRUB config:

    sudo nano /etc/default/grub
    

    Update:

    GRUB_CMDLINE_LINUX_DEFAULT="quiet splash console=tty1 console=ttyS0,115200n8"
    

    Update GRUB:

    sudo update-grub
    

    Now you can always access the VM via:

    qm terminal <VMID>
    

    Even if graphical output is unavailable.


    📌 Summary

    IssueCauseFix
    Can't connect via Proxmox Web ConsoleVM using real GPU instead of emulated oneUse SSH or serial console
    No display output at allMonitor not connected to passed-through GPUConnect monitor to GPU directly
    VM fails to bootDriver issue or incorrect GPU bindingDouble-check vfio-pci setup and VM config
    Want to keep console accessNeed emulated displayAdd vga: qxl and display: spice

    ❓Need Help Debugging?

    Let me know:

    • Did you try SSH? Was the VM reachable?
    • Is there a monitor connected to the GPU?
    • Are you running a GUI (Ubuntu Desktop) or headless (Ubuntu Server)?
    • Output of qm config <VMID>
    • Output of lspci -v on the host

    I’ll help you get back online and fully using your GPU-passthrough VM.

    Would you like a script to automate some of these fixes?

  7. User

    Since following the guide the vm no longer has an ip address

  8. Qwen Assistant

    Thanks for the update — if your VM is no longer getting an IP address after GPU passthrough, this typically means something went wrong during boot or the kernel is crashing due to GPU driver issues.

    Let’s go through a step-by-step troubleshooting guide, explaining what could be happening and how to fix it.


    🧠 Understanding What Might Be Happening

    When you pass through a real GPU (like your NVIDIA GTX 1060) to a VM:

    • The VM no longer uses the emulated graphics device.
    • If the GPU isn’t properly bound to vfio-pci, or if the NVIDIA drivers cause a conflict, the VM may fail to boot properly.
    • If the VM fails to fully boot, services like networking won’t start → no IP address assigned.

    This can happen even with a headless server VM — because the kernel might panic when trying to initialize the GPU via VFIO or NVIDIA drivers.


    🔍 Step-by-Step Troubleshooting Guide


    ✅ 1. Check if the VM is Actually Running

    Run in Proxmox host shell:

    qm status <VMID>
    

    You should see something like:

    status: running
    

    If it's not running, start it:

    qm start <VMID>
    

    Then check the logs:

    qm log <VMID>
    

    Look for any errors around booting or device initialization.


    📜 2. View the VM's Serial Console Output

    This is the most reliable way to see what’s happening during boot even without network or GUI.

    In Proxmox host:

    qm terminal <VMID>
    

    ⚠️ This only works if you've configured a serial console inside the VM OS.

    If you haven't already done that, skip ahead to Section 6 to set it up now.


    🧪 3. Temporarily Disable GPU Passthrough

    To isolate whether the issue is caused by GPU passthrough:

    Edit VM config:

    qm edit <VMID>
    

    Remove or comment out the line:

    hostpci0: ...
    

    Save and restart the VM:

    qm stop <VMID>
    qm start <VMID>
    

    Now wait a few moments and check if it gets an IP again.

    Check from Proxmox host:

    arp -a | grep :<VM-MAC>
    

    Or look in /var/lib/misc/dnsmasq.leases (if using internal bridge with DHCP):

    cat /var/lib/misc/dnsmasq.leases
    

    If it gets an IP now → the problem is definitely related to GPU passthrough.


    🛠️ 4. Ensure the GPU Is Properly Bound to vfio-pci

    From the Proxmox host, run:

    lspci -v
    

    Find your GPU:

    01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB] (rev a1)
            Subsystem: ... some vendor
            Flags: bus master, fast devsel, latency 0,
            I/O ports at 3000 [size=128]
            Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
            Memory at b0000000 (64-bit, prefetchable) [size=256M]
            Capabilities: [60] Power Management version 3
            Capabilities: [68] MSI: Enable- Count=1/1 Maskable-
            Capabilities: [78] Express Endpoint, MSI 00
            Kernel driver in use: vfio-pci
            Kernel modules: nvidiafb, nouveau
    

    Make sure you see:

    Kernel driver in use: vfio-pci
    

    If it says nouveau or nothing, then the GPU is not bound correctly.

    To bind it manually:

    echo -n "0000:01:00.0" > /sys/bus/pci/drivers/vfio-pci/bind
    echo -n "0000:01:00.1" > /sys/bus/pci/drivers/vfio-pci/bind
    

    If this gives an error, double-check:

    • That you blacklisted nouveau and nvidia
    • That vfio-pci is loaded (lsmod | grep vfio)
    • That iommu=pt intel_iommu=on are in GRUB config
    • That IOMMU groups are sane (see below)

    🧬 5. Check for IOMMU Group Issues

    Sometimes devices cannot be passed through if they're not isolated in their own IOMMU group.

    Run:

    sudo apt install virt-manager libvirt-daemon-system
    

    Then:

    sudo virt-host-validate
    

    And also:

    lspci -v
    

    Use this tool (or manual inspection) to verify whether your GPU is in a clean IOMMU group.

    💡 You want each function of the GPU (e.g., 01:00.0 and 01:00.1) to be in the same IOMMU group and not shared with other devices.

    If they're grouped with audio or other onboard devices, you may need to passthrough those too.


    📞 6. Set Up Serial Console (for Future Debugging)

    Even if the VM doesn’t have a display or network, the serial console lets you see boot messages.

    In VM config:

    qm edit <VMID>
    

    Add:

    serial0: socket
    

    Inside the Ubuntu guest, do:

    sudo nano /etc/default/grub
    

    Update:

    GRUB_CMDLINE_LINUX_DEFAULT="quiet splash console=tty1 console=ttyS0,115200n8"
    

    Update GRUB:

    sudo update-grub
    

    Now you can access the serial output:

    qm terminal <VMID>
    

    This will help you see exactly where the boot process is failing.


    📋 Summary Checklist

    StepActionPurpose
    1qm status <VMID>Confirm VM is actually running
    2qm terminal <VMID>See boot/log messages via serial console
    3Remove GPU passthrough lineTest if VM boots normally without GPU
    4lspci -vCheck if GPU is bound to vfio-pci
    5Manually bind GPUForce binding to correct driver
    6Set up serial consoleAllow debugging even without network
    7virt-host-validateCheck for IOMMU issues

    🛎️ Need Help Right Now?

    If you'd like, I can walk you through checking each step one by one — just paste the output of these commands:

    1. qm status <VMID>
    2. qm config <VMID>
    3. lspci -v on the Proxmox host (around your GPU)
    4. cat /etc/modprobe.d/vfio.conf
    5. cat /etc/default/grub
    6. update-initramfs -u output

    With that info, I can give you exact steps tailored to your setup.

    Would you like to continue troubleshooting together?

  9. User

    neither of the files listed in step 2 exist on the vm

  10. Qwen Assistant

    Thank you for the clarification — when you said "neither of the files listed in step 2 exist on the VM", I assume you're referring to:

    • /etc/modprobe.d/vfio.conf
    • /etc/modprobe.d/blacklist-nvidia.conf

    And that you're checking these inside the Ubuntu VM, not the Proxmox host.


    🧠 Important Clarification

    These configuration files (vfio.conf, blacklist-nvidia.conf) are part of the Proxmox host setup, not the guest VM.

    They control how the host kernel binds PCIe devices like your GPU before they are passed through to the VM. These settings have no effect inside the VM itself, because by then the device has already been assigned.

    ✅ So it's perfectly normal and expected that those files do not exist inside the VM.

    You only need them on the Proxmox host, where the GPU is physically located and being managed from.


    🔁 Recap: Where Things Belong

    File / SettingLocationPurpose
    vfio.confProxmox host (/etc/modprobe.d/)Tells the host to bind GPU to vfio-pci
    blacklist-nvidia.confProxmox host (/etc/modprobe.d/)Prevents host drivers from claiming GPU
    GRUB config (intel_iommu=on)Proxmox host (/etc/default/grub)Enables IOMMU support at boot
    NVIDIA driversGuest VMUsed by the VM to talk to the GPU after passthrough

    🛠️ What You Should Be Checking Inside the VM

    Since you're inside the Ubuntu VM, here’s what you should check instead:

    1. Is the GPU visible inside the VM?

    Run:

    lspci | grep -i nvidia
    

    If you see output like:

    0001:01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB]...
    

    Then the GPU was successfully passed through!


    2. Are the NVIDIA drivers installed?

    Check with:

    nvidia-smi
    

    If it runs and shows your GPU, then everything is working!

    If it says command not found, install the drivers:

    sudo apt update
    sudo apt install nvidia-driver-535
    

    Then reboot:

    sudo reboot
    

    3. Can you access the VM via SSH or serial console?

    Try connecting from another machine:

    ssh username@vm-ip-address
    

    Or if you've set up a serial console (as described earlier):

    qm terminal <VMID>
    

    This will help you troubleshoot even if no GUI or network display is available.


    📋 Summary

    QuestionAnswer
    Should vfio.conf and blacklist-nvidia.conf exist inside the VM?❌ No — they belong on the Proxmox host, not the guest VM
    How do I know the GPU is passed through?Run lspci inside the VM — you should see your NVIDIA GPU listed
    How do I use the GPU inside the VM?Install the NVIDIA drivers inside the VM (nvidia-driver-535)
    How do I debug the VM if it doesn’t get an IP?Use qm terminal <VMID> or SSH if available

    🧪 Need Help Now?

    Please run these commands inside the Ubuntu VM and paste the output:

    1. lspci | grep -i nvidia
    2. ip a (to check for IP address)
    3. systemctl status networking or journalctl -b (to check for boot/network issues)

    Also tell me:

    • Are you running a GUI (like Ubuntu Desktop), or just server?
    • Did you try SSH or serial console?

    I’ll help you get back online and confirm whether the GPU is working inside the VM.

    Would you like to continue troubleshooting together right now?

  11. User

    y

  12. Qwen Assistant

    Great! Let's continue troubleshooting together. Please do the following inside your Ubuntu VM (via SSH or serial console if available):


    🔧 Run These Commands and Paste the Output

    1. Check if the GPU is visible inside the VM:

      lspci | grep -i nvidia
      
    2. Check network status / IP address:

      ip a
      
    3. Check system logs for boot issues:

      journalctl -b
      

      Just paste the last 10–15 lines if it's too long.

    4. Check networking service status:

      systemctl status networking
      
    5. (Optional) If you tried installing NVIDIA drivers, check for errors:

      dmesg | grep -i nvidia
      

    📝 Also Tell Me:

    • Is this an Ubuntu Server or Ubuntu Desktop VM?
    • Did you install the NVIDIA driver inside the VM yet?
    • Can you access the VM via SSH or serial console (qm terminal <VMID>), or are you completely locked out?

    Once I have that info, I’ll help you:

    • Confirm whether the GPU is correctly passed through
    • Fix any networking issues
    • Ensure the VM boots properly with GPU passthrough

    Ready when you are! 👇

  13. User

    We now have the vm IP address back. Now I need to add the GPU again

  14. Qwen Assistant

    Great news that you've got the VM IP address back — that means the VM is booting and networking is working again.

    Now, let's re-add the GPU passthrough safely and make sure the VM still boots and remains accessible.


    🛠️ Step-by-Step: Re-Add GPU Passthrough Safely

    We're going to:

    1. Make sure the GPU is still bound to vfio-pci on the Proxmox host
    2. Add the GPU back to the VM config
    3. Boot the VM and verify GPU is visible and working
    4. Ensure networking and SSH remain accessible

    🔍 Step 1: Confirm GPU Is Bound to vfio-pci (On Proxmox Host)

    Run on Proxmox host:

    lspci -v
    

    Look for your GPU, e.g.:

    01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB]...
            Kernel driver in use: vfio-pci
    

    If it says nouveau or no driver is listed, re-bind it:

    echo -n "0000:01:00.0" > /sys/bus/pci/drivers/vfio-pci/bind
    echo -n "0000:01:00.1" > /sys/bus/pci/drivers/vfio-pci/bind
    

    ⚠️ Replace 01:00.0 and 01:00.1 with your actual GPU PCIe addresses.


    🧩 Step 2: Add GPU Back to VM Config

    Edit your VM config:

    qm edit <VMID>
    

    Add this line (or re-add it if you removed it):

    hostpci0: 01:00.0;01:00.1,pcie=1,x-vga=1
    

    Or just the GPU (without audio):

    hostpci0: 01:00.0,pcie=1,x-vga=1
    

    Also ensure:

    machine: q35
    

    This ensures PCIe support for the GPU.


    🚀 Step 3: Start the VM and Check for IP

    Start the VM:

    qm start <VMID>
    

    Check for IP address:

    qm guest cmd <VMID> network-get-interfaces
    

    Or use:

    arp -a | grep :<VM-MAC>
    

    Or check:

    cat /var/lib/misc/dnsmasq.leases
    

    If the VM boots and gets an IP again — great!


    🖥️ Step 4: Check GPU Inside the VM

    SSH into the VM:

    ssh username@vm-ip
    

    Then check:

    lspci | grep -i nvidia
    

    You should see something like:

    01:00.0 VGA compatible controller: NVIDIA Corporation GP106 [GeForce GTX 1060 3GB]...
    

    Now install the NVIDIA driver inside the VM (if not already):

    sudo apt update
    sudo apt install nvidia-driver-535
    

    Then reboot the VM:

    sudo reboot
    

    After reboot, check:

    nvidia-smi
    

    If it shows your GPU, you're done! 🎉


    🧪 Optional: Keep Console Access

    To keep access even if GUI breaks:

    Add this to VM config:

    vga: qxl
    display: spice
    

    This gives you a fallback emulated GPU for the Proxmox console.

    You can also keep the serial console enabled:

    serial0: socket
    

    Inside the VM:

    sudo nano /etc/default/grub
    

    Add serial console support:

    GRUB_CMDLINE_LINUX_DEFAULT="quiet splash console=tty1 console=ttyS0,115200n8"
    

    Then:

    sudo update-grub
    

    Now you can always access the VM via:

    qm terminal <VMID>
    

    ✅ Summary Checklist

    TaskDone?
    GPU bound to vfio-pci on host✅
    VM config has hostpci0: 01:00.0...✅
    VM boots and gets IP✅
    GPU visible via lspci inside VM✅
    NVIDIA drivers installed (nvidia-smi works)✅
    Serial console or fallback display enabled (optional)✅

    📞 Final Check

    Let me know:

    • Whether the VM got an IP after booting with GPU
    • Output of lspci | grep -i nvidia inside the VM
    • Output of nvidia-smi after driver install

    If everything works, you're all set! If not, we can debug further together.

    Would you like to continue with this step-by-step verification now?

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.