Derive this formula step by step: Water calorimeter: W = m₁(Th - Tf) - m₂(Tf - Tl)
- User
Derive this formula step by step:
Water calorimeter:
W = m₁(T_h - T_f) - m₂(T_f - T_l) - Assistant
Below is one common way to derive the formula using energy conservation. In an experiment with a water calorimeter, you mix hot water with cold water inside the calorimeter. When everything comes to a final equilibrium temperature (T_f), the heat lost by the hot water is equal to the heat gained by the cold water plus the heat absorbed by the calorimeter. (The calorimeter does not contain water but its ability to absorb heat is measured in “grams of water equivalent” and is denoted by (W).)
For simplicity, assume that the specific heat (c) of water is the same for all parts of the system. (Since (c) will appear in every term, we can cancel it out.) Let
- (m_1) = mass of hot water at initial temperature (T_h),
- (m_2) = mass of cold water at initial temperature (T_l),
- (T_f) = final equilibrium temperature, and
- (W) = water equivalent (mass) of the calorimeter.
Step 1. Write the Energy Balance
-
Heat released by the hot water:
[ Q_{\text{hot}} = m_1 c (T_h - T_f) ]
-
Heat gained by the cold water:
[ Q_{\text{cold}} = m_2 c (T_f - T_l) ]
-
Heat gained by the calorimeter:
Since the calorimeter’s water equivalent is (W), the heat it gains is
[ Q_{\text{cal}} = W c (T_f - T_l) ]
Step 2. Set Up the Energy Conservation Equation
Because the system is isolated (ignoring any losses to the surroundings), the heat lost by the hot water will equal the heat gained by the cold water and the calorimeter:
[ m_1 c (T_h - T_f) = m_2 c (T_f - T_l) + W c (T_f - T_l) ]
Notice that every term has a factor (c). We can cancel (c) in the entire equation:
[ m_1 (T_h - T_f) = m_2 (T_f - T_l) + W (T_f - T_l) ]
Step 3. Solve for (W)
We want to isolate (W). Subtract (m_2 (T_f - T_l)) from both sides:
[ m_1 (T_h - T_f) - m_2 (T_f - T_l) = W (T_f - T_l) ]
Finally, solve for (W) by dividing both sides by ((T_f - T_l)) (assuming (T_f \neq T_l)):
[ W = \frac{m_1 (T_h - T_f) - m_2 (T_f - T_l)}{T_f - T_l} ]
Note on the Given Formula
The formula presented in your question is:
[ W = m_1 (T_h - T_f) - m_2 (T_f - T_l) ]
This version is equivalent to the derived expression above if the measured temperature rise of the cold water (i.e. (T_f - T_l)) is one degree (or one unit of temperature). In many laboratory exercises the temperature differences are small and, by design or convention, the temperature interval is set so that the denominator is 1. Otherwise, the full expression with the division should be used.
Final Summary
-
Energy conservation:
[ m_1 (T_h - T_f) = m_2 (T_f - T_l) + W (T_f - T_l) ] -
Solved for (W):
[ W = \frac{m_1 (T_h - T_f) - m_2 (T_f - T_l)}{T_f - T_l} ] -
Special case: If ((T_f - T_l) = 1) (in the chosen units), then
[ W = m_1 (T_h - T_f) - m_2 (T_f - T_l) ]
This step-by-step derivation shows how the formula is obtained from the basic conservation of energy principle in calorimetry.
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.