Skip to content
The Chat Archive
gemma-3n-e4b-it· Google LMArena Human Preference 140K

Im trying to create a cad for a 4 legged spider type robot with 3 axes per leg (12 axes…

  1. User

    Im trying to create a cad for a 4 legged spider type robot with 3 axes per leg (12 axes total). id like to optimize the robot for high speed, but would like to create a scale prototype of it. The full scale robot should be around 5 feet tall. I would like to make a scale prototype roughly 1-2 feet tall for testing and for cheap prototyping. It should be optimized for payload carrying capacity. Please create a step by step list of what should be done, and find all relevant dimensions for this robot, including motor and actuator selections

  2. Assistant

    Okay, let's break down the process of designing a 1-2 foot tall, payload-optimized, high-speed 4-legged spider robot with 3 axes per leg (12 total). This is a complex project, so we'll go step-by-step. I'll provide dimensions, motor/actuator suggestions, and considerations for each stage. I'll also emphasize the trade-offs between speed, payload, and cost.

    Phase 1: Conceptual Design & Requirements Definition

    1. Define Payload: Crucially, what is the maximum weight you need the robot to carry? Let's assume a starting point of 1 kg (2.2 lbs) for this prototype. This will drive many of the design choices. If you have a different payload in mind, adjust all calculations accordingly.

    2. Desired Speed: What is the target speed? This is tricky to quantify without a specific application. Let's aim for a maximum speed of 0.5 m/s (1.1 mph) for the prototype. This is a reasonable starting point for a small, agile robot.

    3. Environment: Where will the robot operate? (Flat surfaces, uneven terrain, obstacles?) This influences leg length, joint range of motion, and foot design. Let's assume a relatively flat, indoor environment for the prototype.

    4. Control System: How will the robot be controlled? (ROS, custom code, etc.) This will influence the complexity of the mechanical design and the required processing power. For prototyping, a simpler control system is preferable.

    5. Budget: What is your approximate budget for the prototype? This will heavily influence component choices. Let's assume a budget of 500−500-1000 for the prototype.

    Phase 2: Mechanical Design & Dimensioning (1-2 Foot Scale)

    This is the core of the project. We'll focus on a design that balances speed, payload, and manufacturability.

    1. Overall Dimensions:

      • Height: 1.5 feet (45 cm) - 2 feet (60 cm) - Let's target 1.75 feet (53 cm) for a good balance.
      • Body Width: 6-8 inches (15-20 cm) - This provides stability. Let's use 7 inches (18 cm).
      • Body Depth: 6-8 inches (15-20 cm) - This provides stability. Let's use 7 inches (18 cm).
      • Leg Length: This is critical. A good starting point is to have leg lengths that are roughly 1.5-2 times the body height. Let's aim for 12 inches (30 cm). This gives a good reach.
    2. Leg Design (Each Leg):

      • Segment Count: 3 segments per leg (as requested). This provides good flexibility.
      • Segment Lengths: Distribute the leg length among the segments. A common approach is to have the segments progressively shorter towards the foot. Example:
        • Segment 1 (Body to Hip): 4 inches (10 cm)
        • Segment 2 (Hip to Knee): 5 inches (13 cm)
        • Segment 3 (Knee to Foot): 3 inches (8 cm)
      • Joint Placement: The joints should be positioned to allow for a wide range of motion (ROM) and to minimize stress on the actuators. Consider the geometry of the leg segments and the desired gait.
      • Foot Design: This is crucial for traction and stability. Consider:
        • Shape: Rounded pads, claws, or a combination. Rounded pads are good for flat surfaces.
        • Material: Rubber or TPU (Thermoplastic Polyurethane) for good grip.
        • Size: Foot diameter of 2-3 inches (5-8 cm) is a good starting point.
        • Number of Feet: 4 feet.
    3. Body Design:

      • Material: 3D-printed PLA or PETG are good choices for prototyping. Consider ABS for higher strength.
      • Structure: A simple box-like structure is sufficient for the prototype. Ensure there are mounting points for the legs and the control electronics.
      • Weight: Minimize the body weight to maximize payload capacity.
    4. Joint Design:

      • Type: Revolute joints (rotational) are the most common for legged robots.
      • Range of Motion (ROM): Each joint should have a ROM of at least 180 degrees to allow for a natural gait. Consider slightly less (160-170 degrees) to reduce stress on the actuators.
      • Link Connections: Use robust connection methods (e.g., screws, pins, or custom-designed connectors) to ensure the joints can withstand the forces generated during locomotion.

    Phase 3: Actuator & Motor Selection

    This is where the trade-offs between speed, torque, and cost become apparent.

    1. Actuator Type: Servo Motors are the most common choice for small robots due to their ease of control and relatively low cost. Brushless DC (BLDC) motors with gearboxes offer higher torque and efficiency but are more complex to control. For the prototype, servos are recommended.

    2. Servo Motor Specifications:

      • Torque: This is the most important specification. You need enough torque to lift the payload and move the legs. Calculate the required torque for each joint based on the weight of the payload and the geometry of the leg. A good starting point is 1-2 Nm (Newton-meters) per joint. This is a conservative estimate.
      • Speed: Higher servo speeds will allow for faster locomotion. Look for servos with a speed of at least 300-400 seconds/sec (sec/s).
      • Voltage: Typically 6V or 7.4V.
      • Size: Choose servos that are compact enough to fit within the leg segments.
      • Example Servo: Consider servos like the Savox SC-1235SG or Hitec HS-645MG. These are popular choices for robotics projects.
    3. Motor/Gearbox Considerations (If using BLDC):

      • Torque: Calculate the required torque for each joint.
      • Speed: Determine the desired joint speed.
      • Gear Ratio: Choose a gear ratio that provides sufficient torque at the desired speed.
      • Motor Size: Select a motor that is compact enough to fit within the leg segments.

    Phase 4: Electronics & Control System

    1. Microcontroller: An Arduino Nano or ESP32 is a good choice for prototyping. The ESP32 offers built-in Wi-Fi and Bluetooth, which can be useful for remote control and data logging.

    2. Motor Drivers: You'll need motor drivers to control the servo motors or BLDC motors. PCA9685 is a popular servo driver for Arduino. For BLDC motors, you'll need a dedicated BLDC motor driver.

    3. Power Supply: A LiPo battery is a good choice for powering the robot. Choose a battery with sufficient capacity to provide the required power for the motors and electronics.

    4. Sensors (Optional): Consider adding sensors such as:

      • Inertial Measurement Unit (IMU): For measuring the robot's orientation and acceleration.
      • Force Sensors: In the feet to measure ground contact forces.
      • Distance Sensors (e.g., ultrasonic or LiDAR): For obstacle avoidance.
    5. Control Algorithm: A simple gait control algorithm (e.g., a wave-like motion) is sufficient for the prototype. More advanced algorithms (e.g., inverse kinematics) can be used to improve the robot's performance.

    Phase 5: Prototyping & Testing

    1. 3D Printing: Use a 3D printer to fabricate the mechanical components.
    2. Assembly: Assemble the robot according to the design.
    3. Software Development: Write the code to control the motors and sensors.
    4. Testing: Test the robot's performance in a controlled environment.
    5. Iteration: Iterate on the design based on the test results.

    Relevant Dimensions Summary (Prototype - 1.75 ft Tall)

    • Overall Height: 1.75 feet (53 cm)
    • Body Width: 7 inches (18 cm)
    • Body Depth: 7 inches (18 cm)
    • Leg Length: 12 inches (30 cm)
    • **Segment Lengths (

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.