OpenWrt: dsl: 100.000 Mb/s, Wireless radio0 40 Mbit/s, but router support 900 MBit/s…
- User
OpenWrt: dsl: 100.000 Mb/s, Wireless radio0 40 Mbit/s, but router support 900 MBit/s (5GHz) & 400 MBit/s (2,4 GHz), what to do
- Assistant
Your wireless performance is significantly underperforming compared to both your internet speed and router capabilities. Here's how to diagnose and fix this:
Check your wireless configuration first:
In the OpenWrt web interface, go to Network → Wireless and verify:
- You're using 802.11ac on 5GHz (for the 900 Mbps capability)
- Channel width is set to 80MHz or 160MHz (not 20MHz)
- You're connected to the 5GHz band, not 2.4GHz
Test wired vs wireless performance: Connect directly via Ethernet to confirm you're getting close to 100 Mbps. If not, the issue might be with your DSL configuration or QoS settings.
Optimize wireless settings:
- Use a less congested 5GHz channel (36, 44, 149, 157)
- Ensure your client device supports 802.11ac
- Check if band steering is forcing devices to 2.4GHz
- Disable any bandwidth limiting in Network → QoS
Physical factors:
- Test closer to the router to rule out distance/interference
- Check for obstacles, microwaves, or other 2.4GHz devices
- Verify all antennas are properly connected
OpenWrt specific checks:
- Update to latest OpenWrt version if possible
- Check if wireless drivers need updating
- Look for any error messages in System → Kernel Log
What's your current OpenWrt version and router model? Also, are you testing on 2.4GHz or 5GHz, and what client device are you using?
- User
How to activate 5ghz with same credentials as 2.4? What to set for "Coverage cell density". Do i have to activate 802.11ac/n (thought it is uses for e.g. visitors WiFi)? Do mobile phones etc automatically connect to 5ghz or how it works? Or can i just change 2.4 that it uses 5ghz and is it recommended?
- Assistant
Setting up 5GHz with same credentials:
You have two options:
Option 1: Single SSID (both bands, same name/password)
- Go to Network → Wireless
- Configure both radio0 (2.4GHz) and radio1 (5GHz) with identical SSID and password
- This creates "band steering" where devices automatically choose the best band
Option 2: Separate SSIDs (recommended for troubleshooting)
- Name them differently like "YourWiFi_2.4" and "YourWiFi_5G"
- Same password for both
- Gives you control over which band devices use
Coverage cell density: Set this to "High density" (3) for most home environments. This optimizes power output and reduces interference. Only use "Low density" (1) if you're in a very isolated area.
802.11ac/n activation: Yes, absolutely activate this! 802.11ac is the modern WiFi standard that gives you those high speeds. It's not for guest networks - it's the main wireless protocol. In OpenWrt:
- Enable 802.11ac on 5GHz radio
- Enable 802.11n on both radios
- Set channel width to 80MHz on 5GHz
How devices connect:
- With single SSID: Most modern phones automatically prefer 5GHz when signal is strong
- With separate SSIDs: You manually choose which network to connect to
- Older devices might stick to 2.4GHz even with single SSID
Don't disable 2.4GHz entirely - keep both active. 2.4GHz has better range and some IoT devices only support it. Modern setup should have both bands running simultaneously.
Would you like me to walk you through the specific OpenWrt interface steps for either configuration option?
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.