what is cmd42? how to unlock cmd42 locked sd card with linux?
- User
what is cmd42? how to unlock cmd42 locked sd card with linux?
- Assistant
What is CMD42?
CMD42 is a specific command within the SD card protocol that's used to set a temporary write protection on the card. It's often used in applications where you want to prevent accidental or unauthorized data modification. When an SD card is locked using CMD42, it becomes read-only until the lock is explicitly removed (or sometimes until power is cycled).
Think of it as a software-based write-protection mechanism, distinct from the physical write-protect switch that some SD cards have.
Unlocking a CMD42 Locked SD Card with Linux
Unlocking a CMD42 locked SD card in Linux generally involves sending the correct command to the card via the command line. This isn't guaranteed to work in every situation, as some CMD42 implementations might be more persistent or secure than others. However, here's a common approach:
1. Identify the SD Card Device:
-
First, you need to determine the device name that Linux has assigned to your SD card. This is often something like
/dev/sdb,/dev/sdc, or/dev/mmcblk0. -
Use the
lsblkcommand to list block devices. This will show you all the storage devices connected to your system, along with their sizes and mount points. Look for a device that corresponds to the size of your SD card.lsblkExample output:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 477G 0 disk ├─sda1 8:1 0 476G 0 part / ├─sda2 8:2 0 1K 0 part └─sda5 8:5 0 8G 0 part [SWAP] sdb 8:16 1 14.8G 0 disk └─sdb1 8:17 1 14.8G 0 part /media/user/SD_CARDIn this example,
/dev/sdbappears to be the SD card (14.8GB). If the SD card has partitions (likesdb1in the example), you need to target the whole card device (e.g.,/dev/sdb).
2. Use
mmcutility (most common):The
mmcutility is part of themmc-utilspackage and is the most standard way to interact with SD cards at a low level.-
Install
mmc-utils:sudo apt update # or your distribution's package update command sudo apt install mmc-utils -
Unlock the SD Card:
The exact command may depend slightly on your card, but try this as a starting point, carefully replacing
/dev/sdbwith your actual device name:sudo mmc lock remove /dev/sdbIf that doesn't work, try specifying a "password" (often just zeros):
sudo mmc lock remove /dev/sdb 00000000Explanation of the command:
sudo: You usually need root privileges to directly access block devices.mmc: The MMC (MultiMediaCard) utility. SD cards use the MMC protocol.lock remove: Tellsmmcto remove the write protection lock./dev/sdb: The device name of your SD card.00000000: The "password." Many CMD42 implementations use a simple, often zeroed-out, password for the lock. If you know a specific password was used, substitute it here. This is usually in hexadecimal format.
-
Verify: After running the command, try writing a small file to the SD card to confirm that it's no longer read-only. You might need to unmount and remount the card first:
sudo umount /dev/sdb1 # or whatever the mount point is sudo mount /dev/sdb1 /mnt # Remount to /mnt touch /mnt/testfileIf the
touchcommand succeeds, the SD card is likely unlocked.
3. Alternative Approach (less common, more complex, proceed with caution):
sg_rawThe
sg_rawcommand sends arbitrary SCSI commands to a device. It's more powerful but also more dangerous if used incorrectly. You need to know the specific SCSI command sequence for clearing the CMD42 lock. This is highly dependent on the SD card's implementation, and finding the correct sequence can be difficult. Usingsg_rawincorrectly can potentially damage your SD card.-
Install
sg3_utils:sudo apt update sudo apt install sg3-utils -
Find the SCSI ID:
sudo sg_scanLook for your SD card in the output. The SCSI ID will look something like
scsi1 channel=0 id=0 lun=0. You need the device name (e.g.,/dev/sg1). -
Attempt to Unlock (Example - extremely generic and unlikely to work directly):
sudo sg_raw /dev/sg1 A1 00 00 00 00 00 00 00 00 00 00 00 # This is a placeholder!sg_raw: The SCSI generic command tool./dev/sg1: The SCSI device name fromsg_scan. Replace this with your actual device name.A1 00 00 00 00 00 00 00 00 00 00 00: This is the SCSI command. THIS IS A PLACEHOLDER! You need the specific command for unlocking your SD card. This is where you need to find the correct SCSI sequence to clear the lock. This often involves sending the CMD42 command with appropriate parameters (address, password, etc.).
Important Considerations and Warnings:
- Data Loss: While the goal is to unlock the SD card, there's always a risk of data loss if commands are entered incorrectly. Back up any important data on the card before attempting these steps, if possible.
- Incorrect Device: Double-check the device name (
/dev/sdb,/dev/sg1, etc.) before running any commands. You could accidentally format or damage the wrong disk if you're not careful. - CMD42 Implementation: The specific command sequence required to unlock the SD card depends on how CMD42 was implemented on the card itself. If the default commands don't work, you may need to research the specific SD card manufacturer or the device that locked the card to find the correct unlocking sequence.
- Physical Lock: Make sure the physical write-protect switch on the SD card (if it has one) is in the unlocked position. This may seem obvious, but it's easy to overlook.
- File System Corruption: If the SD card was improperly removed or a write operation was interrupted before the lock was set, the file system might be corrupted. In this case, you might need to run
fsckor a similar file system repair tool after unlocking the card.
Troubleshooting:
- "Operation not permitted" or similar errors: Double-check that you're running the commands with
sudoto gain root privileges. mmcnot found: Make sure you've installed themmc-utilspackage.- Still read-only: Try unmounting and remounting the SD card after running the unlock command. Also, try power cycling the card (remove it and reinsert it).
- Card is physically damaged: If you've tried all the software approaches and the card is still read-only, it's possible that the card is physically damaged.
In summary:
Unlocking a CMD42 locked SD card requires using the
mmccommand (preferred) or, less commonly,sg_rawwith the correct command sequence. Finding the correct command sequence can be tricky and depends on the SD card's implementation of CMD42. Exercise extreme caution, double-check device names, and back up your data if possible. Good luck! -
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.