Skip to content
TheChatArchiveThe Chat Archive
Claudeclaude-3-7-sonnet-20250219· AnthropicHugging Face LMArena Human Preference 140K

better but still odd

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Qwenqwen-max-2025-01-25’s answer.
  1. User

    better but still odd

  2. Claude Assistant

    If the touchscreen calibration still feels odd after using the aspect ratio adjustments, we might need to fine-tune the calibration matrices. This is often a trial-and-error process to get the perfect feel.

    Here are some approaches to improve it:

    1. Try Different Calibration Values

    You can experiment with slightly different values in your config. For example:

    # Try these alternative values for 90° rotation (left)
    bindsym $mod+Shift+l exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1.65 1 0.6 0 0 0 0 1
    
    # Alternative for 270° rotation (right)
    bindsym $mod+Shift+r exec swaymsg output "<OUTPUT>" transform 270 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 1.65 0 -0.6 0 1 0 0 1
    

    2. Add Offset Correction

    Sometimes the issue is that the touch points need a slight offset. You can adjust the translation components (the third column in the matrix):

    # With slight offset correction for 90° rotation
    bindsym $mod+Shift+l exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1.78 1.05 0.5625 0 -0.02 0 0 1
    

    The 1.05 and -0.02 values add small offsets to help align touch points.

    3. Use a Diagnostic Approach

    To find the perfect values, you can create a simple diagnostic mode:

    # Diagnostic mode - try different calibration values
    bindsym $mod+Shift+1 exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1.7 1 0.58 0 0 0 0 1
    
    bindsym $mod+Shift+2 exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1.8 1 0.55 0 0 0 0 1
    
    bindsym $mod+Shift+3 exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1.9 1 0.52 0 0 0 0 1
    

    This lets you quickly switch between different calibration settings to find what works best.

    4. Consider Using libinput's Built-in Calibration

    If your device supports it, you might get better results using libinput's calibration tools:

    sudo apt install libinput-tools
    

    Then run:

    libinput measure touchscreen-calibration
    

    This will guide you through a calibration process that might give more accurate results.

    5. Try a Simpler Approach

    Sometimes, the simplest approach works better:

    # Simple approach - just swap axes without scaling
    bindsym $mod+Shift+l exec swaymsg output "<OUTPUT>" transform 90 \
      && swaymsg input "<TOUCHSCREEN>" calibration_matrix 0 -1 1 1 0 0 0 0 1
    

    6. Check for Specific Device Quirks

    Some touchscreens have specific quirks or need special handling. You might want to search for your specific device model to see if others have found optimal calibration settings.


    Let me know which of these approaches you'd like to try, or if you'd prefer a completely different solution. Finding the perfect calibration often requires some experimentation.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.