Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen-max-2025-01-25· Alibaba (Qwen)Hugging Face LMArena Human Preference 140K

Assume I have a rigid cylinder. ID is 20mm. I want to cool a rod of material down so…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Claudeclaude-opus-4-20250514’s answer.
  1. User

    Assume I have a rigid cylinder. ID is 20mm. I want to cool a rod of material down so that it just fits inside this rigid cylinder. I will use LN. I am looking for materials which will exert the highest pressure

  2. Qwen Assistant

    To determine which material will exert the highest pressure when cooled to fit inside the rigid cylinder, we need to consider the thermal expansion coefficient (α\alpha) of the material. The thermal expansion coefficient determines how much a material shrinks (or expands) per degree of temperature change.

    Key Concept:

    When a material is cooled, it contracts. If you cool the rod enough so that its diameter just fits inside the 20 mm inner diameter (ID) of the rigid cylinder and then allow it to warm back up, the rod will expand due to thermal expansion. This expansion creates pressure against the walls of the rigid cylinder.

    The pressure exerted depends on:

    1. Thermal expansion coefficient (α\alpha): Materials with a higher α\alpha shrink more when cooled and expand more when warmed.
    2. Elastic modulus (EE): This measures how resistant a material is to deformation under stress. A higher elastic modulus means the material will exert greater pressure as it tries to return to its original size.
    3. Temperature change (ΔT\Delta T): The greater the cooling or heating, the larger the contraction or expansion.

    Material Selection:

    To maximize the pressure, we want:

    • A material with a high thermal expansion coefficient (α\alpha).
    • A material with a high elastic modulus (EE).

    Common Materials and Their Properties:

    MaterialThermal Expansion Coefficient (α\alpha, 10−6 °C−110^{-6} \, \text{°C}^{-1})Elastic Modulus (EE, GPa)
    Aluminum2370
    Copper17120
    Steel12200
    Invar (Fe-Ni)1.2145
    Polyethylene2000.1-0.2

    Observations:

    1. Aluminum has a high α\alpha but a relatively low EE. It will exert moderate pressure.
    2. Copper has a slightly lower α\alpha than aluminum but a higher EE, leading to higher pressure.
    3. Steel has a lower α\alpha than copper but an even higher EE, resulting in substantial pressure.
    4. Invar has an extremely low α\alpha, making it unsuitable for this application.
    5. Polyethylene has an extremely high α\alpha but a very low EE, meaning it won't exert significant pressure despite significant expansion.

    Best Candidates:

    • Steel: With a high elastic modulus and reasonable thermal expansion, steel will exert significant pressure.
    • Copper: While its elastic modulus is lower than steel's, its higher α\alpha makes it a strong contender.

    Final Recommendation:

    If your goal is to exert the highest pressure, steel is likely the best choice due to its combination of high elastic modulus and sufficient thermal expansion. However, if you want to achieve a balance between ease of cooling and pressure exerted, copper may also be a good option.

    Calculation Example:

    Let’s calculate the pressure exerted by steel when warming up after being cooled to fit into the cylinder.

    1. Initial Diameter: Assume the rod's initial diameter is slightly larger than 20 mm (e.g., 20.1 mm).

    2. Cooling Required: Use the formula for thermal contraction:

      ΔD=D0⋅α⋅ΔT\Delta D = D_0 \cdot \alpha \cdot \Delta T

      where D0=20.1 mmD_0 = 20.1 \, \text{mm}, α=12×10−6 °C−1\alpha = 12 \times 10^{-6} \, \text{°C}^{-1}, and ΔD=0.1 mm\Delta D = 0.1 \, \text{mm} (to fit snugly). Solve for ΔT\Delta T:

      ΔT=ΔDD0⋅α=0.120.1⋅12×10−6≈415 °C.\Delta T = \frac{\Delta D}{D_0 \cdot \alpha} = \frac{0.1}{20.1 \cdot 12 \times 10^{-6}} \approx 415 \, \text{°C}.
    3. Pressure Exerted: Use the relationship between strain, elastic modulus, and pressure:

      P=E⋅ε,P = E \cdot \varepsilon,

      where ε=ΔDD0\varepsilon = \frac{\Delta D}{D_0} is the strain. For steel:

      P=200 GPa⋅0.120.1≈0.995 GPa ( 1000 MPa).P = 200 \, \text{GPa} \cdot \frac{0.1}{20.1} \approx 0.995 \, \text{GPa} \, (\text{~1000 MPa}).

    This is a very high pressure, demonstrating why steel is an excellent choice.

    Final Answer:

    Steel is the material that will exert the highest pressure when cooled and allowed to expand inside the rigid cylinder.\boxed{\text{Steel is the material that will exert the highest pressure when cooled and allowed to expand inside the rigid cylinder.}}

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.