Skip to content
TheChatArchiveThe Chat Archive
Geminigemini-2.5-pro· GoogleHugging Face LMArena Human Preference 140K

As an Juniper expert, please provide the CLI commands for checking wired 802.1x for…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Qwenqwen3-30b-a3b’s answer.
  1. User

    As an Juniper expert, please provide the CLI commands for checking wired 802.1x for troubleshooting mac address, user login, configuration for ports on EX switches

  2. Gemini Assistant

    Of course. As a Juniper expert, here is a comprehensive guide to the CLI commands for troubleshooting wired 802.1X on EX series switches.

    This guide is structured to follow a logical troubleshooting methodology, starting with broad checks and narrowing down to specific issues.

    802.1X Troubleshooting Methodology

    The key players in 802.1X are:

    • Supplicant: The client device (e.g., a laptop) trying to connect.
    • Authenticator: The Juniper EX switch port.
    • Authentication Server: The RADIUS server (e.g., Cisco ISE, ClearPass, NPS).

    Troubleshooting involves checking the state and communication between these three components.


    1. High-Level 802.1X Status (The "50,000 Foot View")

    These commands give you a quick overview of the 802.1X health across the entire switch.

    show dot1x interface

    This is your primary starting point. It shows the status of all interfaces configured for 802.1X.

    user@EX-switch> show dot1x interface
    802.1X Information:
    Interface   Role         State           MAC address          User
    ge-0/0/0.0  Authenticator Authenticated   00:1C:73:00:11:22    j-doe
    ge-0/0/1.0  Authenticator Connecting      00:1C:73:00:33:44    N/A
    ge-0/0/2.0  Authenticator Held            00:1C:73:00:55:66    N/A
    ge-0/0/3.0  Authenticator Disabled        N/A                  N/A
    

    Key State column values:

    • Authenticated: Success! The supplicant has been authenticated by the RADIUS server.
    • Connecting: The switch is actively trying to authenticate the supplicant (EAPOL frames are being exchanged). If it's stuck here, there's likely a problem with the supplicant's configuration or the RADIUS server.
    • Held: The supplicant failed authentication (e.g., bad password). The switch places the port in a "held" state for a configured period (quiet-period) before retrying.
    • Disabled: 802.1X is configured but administratively disabled on the port.

    2. Checking the Configuration for a Specific Port

    If an interface isn't behaving as expected, verify its configuration.

    show configuration interfaces <interface-name>

    Check the specific interface configuration to ensure dot1x is applied.

    user@EX-switch> show configuration interfaces ge-0/0/1
    description "User Access Port";
    unit 0 {
        family ethernet-switching {
            port-mode access;
            vlan {
                members data-vlan;
            }
        }
    }
    

    show configuration protocols dot1x

    Check the global and interface-specific 802.1X protocol settings.

    user@EX-switch> show configuration protocols dot1x
    authenticator {
        authentication-profile-name radius-auth-profile; # Points to RADIUS config
        interface {
            ge-0/0/0.0 {
                supplicant multiple; # Allows multiple supplicants
                retries 3;
                guest-vlan guest;    # Fallback VLAN if auth fails
                server-fail vlan-name voice; # Fallback if RADIUS is unreachable
            }
            ge-0/0/1.0 {
                supplicant single;
                reauthentication 1800; # Re-authenticate every 30 mins
            }
            all; # Default settings for all other interfaces
        }
    }
    

    show configuration access

    Verify the RADIUS server profile is correctly configured.

    user@EX-switch> show configuration access
    profile radius-auth-profile {
        authentication-order radius;
        radius {
            authentication-server [ 10.10.10.100 10.10.10.101 ];
            secret "$9$3yqChtkoSOTdJik279A"; ## SECRET-DATA
        }
    }
    

    3. Troubleshooting a Specific MAC Address

    This is a common task when a user reports their device cannot connect.

    Step 1: Find the interface the MAC address is on.

    user@EX-switch> show ethernet-switching table | match 00:1C:73:00:33:44
    
    Ethernet-switching table: 2 entries, 2 learned
    VLAN           MAC address       Type         Age Interfaces
    data-vlan      *                 Flood          - All-members
    data-vlan      00:1c:73:00:33:44 Learn          0 ge-0/0/1.0
    

    Result: The MAC is on interface ge-0/0/1.0.

    Step 2: Get detailed dot1x information for that interface. This command is the most valuable for deep-diving into a single port's state.

    user@EX-switch> show dot1x interface detail ge-0/0/1.0
    ge-0/0/1.0
      Role: Authenticator
      Administrative-state: Auto
      Supplicant-mode: Single
      Number of retries: 3
      Quiet-period: 60 seconds
      Server-timeout: 30 seconds
      Mac-Radius: Enabled
      Mac-Radius-restrict: Disabled
      Re-authentication: Enabled
      Configured Re-authentication interval: 1800 seconds
      Guest-vlan: guest
      
      PAE state: Connecting      <-- Current state machine position
      Backend-state: Idle        <-- RADIUS communication state
      
      Authentication statistics:
        EAPOL frames received: 15
        EAPOL frames transmitted: 12
        EAP Start packets: 4
        EAP Logoff packets: 0
        EAP-Success packets: 0     <-- No success packets received
        EAP-Failure packets: 3     <-- Failure packets received!
        
      Supplicant: 00:1C:73:00:33:44
        Operational state: Connecting
        Backend state: Idle
        Authentication method: EAP-MD5
        Last EAP-Failure received: EAP-Failure (code 4) from authenticator
    

    Analysis of this output:

    • The port is stuck in the Connecting state.
    • It has received 3 EAP-Failure packets. This indicates the RADIUS server is actively rejecting the authentication attempt.
    • The problem is not switch connectivity to RADIUS, but rather the credentials or policy on the RADIUS server for this supplicant/MAC.

    4. Troubleshooting a Specific User Login

    If a user is being authenticated by username (e.g., PEAP), you can check their status directly.

    show dot1x authenticator user <username>

    This command is useful if the user successfully authenticated and you need to find where they are connected.

    user@EX-switch> show dot1x authenticator user j-doe
    Authenticator  User   MAC Address        Interface   VLAN         State
    PAE            j-doe  00:1C:73:00:11:22  ge-0/0/0.0  data-vlan    Authenticated
    

    If this command returns no output: The user has either not attempted to log in, or their authentication has failed. In this case, you must pivot to troubleshooting by MAC address (as above) and checking the RADIUS server logs for that specific username to see the reason for failure (e.g., incorrect password, certificate issue, expired account).


    5. Verifying RADIUS Server Connectivity

    If multiple clients are failing, the problem could be between the switch (Authenticator) and the RADIUS server.

    show dot1x radius-servers

    Check statistics for communication with the RADIUS servers.

    user@EX-switch> show dot1x radius-servers
    Radius-Server     Address       Port  Status  Requests  Responses  Timeouts   Malformed
    10.10.10.100      10.10.10.100  1812  Up            50         47         3           0
    10.10.10.101      10.10.10.101  1812  Up             0          0         0           0
    
    • A high number of Timeouts is a red flag. It indicates the switch is sending requests, but the RADIUS server isn't responding. Check for network connectivity (ping, traceroute), firewalls, and ensure the switch is defined as a valid RADIUS client on the server with the correct shared secret.

    test aaa

    This is an excellent tool to test the entire authentication chain without needing a physical client.

    # Test a user authentication against the RADIUS server
    user@EX-switch> test aaa user j-doe password <password>
    

    The output will tell you if the authentication was a success or failure, confirming that the switch, RADIUS server, and user credentials are all working correctly.


    6. Advanced Troubleshooting with Traceoptions

    When all else fails, traceoptions provides a verbose log of the entire 802.1X and RADIUS exchange.

    Warning: Use this only for active troubleshooting, as it can be CPU-intensive.

    Step 1: Configure traceoptions.

    # In configuration mode
    set protocols dot1x traceoptions file dot1x-log size 10m files 3
    set protocols dot1x traceoptions flag all
    
    # You might also want to trace the RADIUS process itself
    set access traceoptions file radius-log size 10m files 3
    set access traceoptions flag all
    
    commit
    

    Step 2: Re-run the test (e.g., unplug/replug the client).

    Step 3: View the log file.

    user@EX-switch> show log dot1x-log
    # Look for EAPOL start, request, response, and success/failure packets
    # You will see the entire EAP conversation
    
    user@EX-switch> show log radius-log
    # Look for RADIUS Access-Request, Access-Challenge, and Access-Accept/Reject packets
    

    Step 4: Deactivate traceoptions when finished.

    # In configuration mode
    deactivate protocols dot1x traceoptions
    deactivate access traceoptions
    commit
    

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.