going through this long transmission we're going to measure the 10x probe and and so…
- User
going through this long transmission we're going to measure the 10x probe and and so we're going to see you know rule number nine we're going to see ringing as the signal comes out of this it sees this really low impedance it sees the 13 30 ohms of the transmission line we get most of that volt you know from it's a voltage divid 3 ohms to 130 ohms most of that voltage gets launched in the transmission line travels down travels down travels down and it hits over here and when the scope probe is plugged in it sees an open effectively an open and
00:28:46 so it's going to reflect and it sees okay now I I get that you know roughly I can't remember is this 5 volt 3vt no this a 3.3 volt so 3.3 volt goes down the line hits the open and and what happens at the open well 3.3 goes in how much is going to reflect do you think 3.3 3.3 is going to reflect and so what does the the receiver see what's the voltage of the receiver Sees at that instant 6.6 yeah it sees 3.3 go in 3.3 go it sees it sees both of those um and it's going to see three 3.3 or um six six volts and then that 3.3 volt signal
00:29:28 trans reflects back and it goes back through here 3.3 3.3 3.3 and now it hits the transmitter and the transmitter is like 3 ohm and I go from 130 to three ohms it's almost like a dead short and so it's going to reflect but the reflection coefficient when you go from a high to a low impedance is negative and so that 3.3 hitting there reflects with like minus three volts and so minus 3 volts reflect minus 3us 3us three and hits over here and what happens when minus three hits there it's going to reflect I had 6 volt 6.6 now I have
00:30:06 minus 3.3 and it's going to reflect as minus 3 so I minus 6 volts and so let's see 6.6 it's like a half a volt and so I'm going to drop down to like half a volt and then minus huh what we see there on the right three yeah exactly so here's the actual measured voltage and so here's the initial vol voltage I see at 6.6 that positive 3 volts reflects back hits here reflects as minus three heads back this way and I pulls down like minus 6 and here it is you know minus like7 volts something like that and that minus three
00:30:44 reflects hits here changes sign reflects us like 2.5 volts comes back here now I'm going to see another 2.5 2 that's 5 Vols so it was like uh like one volt added to five Vols there's 5 and a half volts reflects changeing sign and so we see the ringing right so it's the ring it's all the reflections back and forth and even the absolute this is literally the simplest circuit you can have that shows ringing low impedance driver transmission line High impedance receiver and even that is really complicated keeping track of all those
00:31:17 Reflections that's where simulation is really important and um and a lot any spice simulator will simulate this and so um this is the measure me voltage so we literally measure it on a scope we take the scope measurement save it as CSP bring it into our simulation environment and replot it in the simulation environment and and that's what we're doing here replotting in the simulation environment and we see the ring and look oh my gosh it lasts for a long time and why do you think it's stamping why do you think it's dropping
00:31:48 off like that um because making it drop off because the the reflections are not like 100% yes exactly because every time it reflects from here we get most of it reflecting every time it reflects from here well it's not a reflection coefficient of minus one it's like minus. N3 because it's 130 to 3 ohms it's not to zero ohms and so every time reflects we lose a little bit more exactly right what's another explanation for why it damps off why does it drop off didn't you know so you know I ask my students this question all the time right and 90% of
00:32:31 them say oh it's the losses in the transmission line that this is a result of the attenuation in the transmission line so that's another one on the list and there's a third explanation as well of why it keeps dropping off why it drops off like this can you think of a third explanation I couldn't I couldn't think the second one so so well you know most of my students have taken um highspeed digital engineering or design so they're familiar with lossy transmission lines and that's the first thing they think of oh it's losses in the transmission line
00:33:08 um there's another factor and that is you know I I I said at the receiver here I'm sticking the 10x probe and to first order it's just a high impedance resistor but to second order it's a capacitor and the capacitor is going to like you mentioned before it's going to increase the rise time of the signal it's going to slow The Edge down a little bit it's going to make it more slopey and more slopey means it's going to uh not reflect as much it's going to smear out the edges a little bit and so that's a third factor and the the
00:33:36 question is which one is it is it the the difference in the rise time of the or the difference reflection coefficient because it's a a three ohm output impedance is it the losses in the transmission line is it the input capacitance of the of the 10x probe which is causing that drop off and this is where simulation can give us insight because in the simulation tool if we have confidence in it we can play the what if games we can tweak the knob of well how big an impact is the losses turn the losses off and see what the
00:34:09 impact is or turn the losses in the board on make it extreme what's the impact or change that output impedance and what's going to be the impact or change the capacit and so this is where measurement simulation correlation is so valuable because it lets us play those what if games to understand the real root cause so that's the setup we do the measurement and now we build a model and the model that we use is really simple so instead of you know if you use an Ibis model or a spice model for a component um both of those are you get
00:34:46 them from the vendor and you put them in the simulation tool and you push the button and you get an answer but there's no knob to tweak you can't we call them Point solutions they are for that specific case and I don't know how well they apply to my device here that I have on my board um and so while it's always a great starting place they use kind of effec nominal values for the component I I can't explore design space much with them and so I always like to recommend starting with a model that is parameterized so you can make some
00:35:20 changes and that's where the th and model for a transmitter is so valuable that it's a really good first order model of almost every transmitter do you have this model in detail somewhere on these slides or well you know what and I apologize I don't I didn't write it in here because this is a presentation more about measurement simulation correlation and I'm just showing this as an example but um I I am sure we've talked about the model before but um it's really simple um let me see can I draw on this I don't have my touchscreen interface
00:35:52 here um uh let me maybe we can Google it or something uh well yeah actually I was gonna I was going to try to draw it here let me do this um I'm gonna do this I'm G to clear this screen here and now I think I have some drawing tools and so here let me draw it so here's the voltage source ideal voltage source and here is a single ideal resistor so you know whenever you do a simulation whenever you build a model it's always ideal elements right and this model so here's the voltage source and we're going to use a voltage source bu bir yotube transkriptir burada youtber ne anlatıyor bana anlat
- Assistant
Bu YouTuber, elektronik devrelerde özellikle yüksek hızlı sinyal iletiminde yaşanan yansıma (ringing) olayını ve bunun nedenlerini açıklıyor. Anlattığı senaryoda şöyle özetleyebiliriz:
- Bir sinyal (örneğin 3.3V lojik seviyesi) düşük empedanslı bir sürücü (3 ohm gibi) tarafından bir iletim hattına (transmission line) veriliyor.
- İletim hattı, yaklaşık 130 ohm empedansa sahip ve sonunda yüksek empedanslı bir yük (scope probe) var, burada yük neredeyse açık devreymiş gibi (high impedance).
- Sinyal iletim hattı boyunca ilerlerken, yüksek empedanslı uçtan tamamen yansıyor (reflekt oluyor). Bu yansıma sinyalin genliği artıyormuş gibi yapıyor (örneğin 6.6V gibi).
- Sinyal tekrar sürücüye geldiğinde, sürücünün empedansı çok düşük olduğu için (130 ohm’dan 3 ohm’a ani geçiş) yansıma katsayısı negatif oluyor ve yansıma sinyalin işareti tersine dönüyor, yani negatif voltaj şeklinde geri geliyor.
- Bu yansıma ve tekrar yansıma olayları sinyal üzerinde dalgalanmalar (ringing) oluşturuyor.
- Ancak bu dalgalanmalar zamanla sönümleniyor (azalıyor), bunun nedenleri ise:
- İletim hattındaki enerji kayıpları (hat kayıpları, zayıflama).
- Alıcı uçtaki (scope probundaki) kapasitans etkisi sinyalin kenarlarını yumuşatıyor ve yansımanın şiddetini azaltıyor.
- Yansıma katsayılarının (empedans farklılıklarından kaynaklı) 1 veya -1 olmaması (tam yansıma olmayışı).
- YouTuber bu karmaşık olayları modellemek için Spice simulasyonları ve basit, parametre ayarlanabilir modeller öneriyor.
- Son olarak, "Thevenin modeli" gibi ideal bir gerilim kaynağı ve seri direnç kullanarak sürücü devresinin modele dökülmesinden bahsediyor ve simülasyon-mesure (ölçüm) korelasyonunun tasarımı anlamak için ne kadar önemli olduğunu vurguluyor.
Yani kısaca, bu YouTuber:
- Elektronik iletim hatlarında meydana gelen yansıma problemini,
- Bu yansımaların sinyal dalgalanması (ringing) oluşturmasını,
- Ringing’in neden sönümlendiğini,
- Ve bu tür problemlerde ölçüm ve simülasyonun nasıl birlikte kullanılması gerektiğini anlatıyor.
Bu anlatım özellikle yüksek hızlı dijital tasarım, sinyal bütünlüğü (signal integrity), devre modelleme ve simülasyon konularına ilgi duyan mühendisler için faydalı.
- User
here um uh let me maybe we can Google it or something uh well yeah actually I was gonna I was going to try to draw it here let me do this um I'm gonna do this I'm G to clear this screen here and now I think I have some drawing tools and so here let me draw it so here's the voltage source ideal voltage source and here is a single ideal resistor so you know whenever you do a simulation whenever you build a model it's always ideal elements right and this model so here's the voltage source and we're going to use a voltage source
00:36:31 that has uh some rise time to it so it's got a starting voltage here it's got a final voltage here in this case it's like 3.3 volts something like that 3.3 volts um and it's got a rise time associated with it and those are parameters that you can set in the voltage source and then the output resistance has another parameter the resistance M so it it's param I can explore design space with that I can make some changes and see what the result is and this is what the transmitter looks like and then the rest of the circuit for the transmission line
00:37:08 it's literally an ideal transmission line and um now if we want to explore the losses in the transmission line then we need to include a model of a lossy transmission line and this is where different simulation tools vary because not every tool has has a good lossy transmission line model LT spice doesn't symmetric as much as I love it it's lossy transmission line model just has um is not a very good lossy transmission line model Quicks one of my other favorite um free simulation tools has a very good um lossy transmission line
00:37:49 model has dialectric loss in and conductor loss um uh and then um uh hyperlinks of course does and my other favorite tool ads uh key sites uh uh ads has a really great lossy transmission line model in it so if you want to include an effect you got to make sure that the simulation tool supports ideal elements that have that effect in it and so but but you can start out with just a simple uh uniform lossless transmission line so there like there's only connection basically in your simulation uh well so there're two that
00:38:28 Define a uniform transmission line model A Los transmission the delay the time delay is one yep and that effectively is like the length the electrical length and what's the other term that that defines it Los I don't know the characteristic impedance ah INF okay and that and you need that because that's why you have Reflections if you use just a wire connection so here's my receiver and my receiver I'm going to model is just a really high input resistance 10 Meg and then here's here's the the ground connection and then here's the the
00:39:01 ground connection over here and so I'm going to use a really high impedance and if I made this connection here then if I if I Ed just a wire and didn't use a transmission I wouldn't see any Reflections it would just be whatever the output is that's what I'm going to see it's the transmission line and the impedance difference at the two ends so I'm going to put an RX over here just to remind us okay that's at the receiver and this is at the transmitter here this is um it's the this circuit model that gives rise
00:39:33 to those Reflections what we're talking about so this is the simplest simulation what simplest one you could do perfect in symmetrics LT spice even will let you do this and basically the I'm sorry for interrupting basically the trace element it's one of the elements which you can pick and place into your simulation like the voltage power supply resistor then one of the elements it's called a t line m a t element is is what it is that um Universal in all spice tools okay and and this will will predict the that ringing for you and with this you
00:40:07 can explore how does the length of the transmission line and the rise time of the signal how does that play a role in the reflection so you can probe the the point over here at the receiver there's a probe point you measure that um with the or you s you display that voltage there you can see the ringing noise you can change the rise time you can change the length you can change the impedance mismatch between the source and the impedance of the line all those things you can play with with this virtual prototype right and that's the starting
- Assistant
Bu kısımda YouTuber, sinyal iletim hattındaki yansıma (ringing) ve sinyal davranışlarını anlamak için basit ama esnek bir modelleme/simülasyon yaklaşımını anlatıyor. Özetle şunları söylüyor:
-
Model Kurulumu:
- Simülasyonda ideal bir voltaj kaynağı (örneğin 3.3V’luk ve belirli bir yükselme süresine (rise time) sahip) kullanacaklar.
- Bu kaynağın çıkışında idealleştirilmiş bir seri direnç (mesela 3 ohm gibi) olacak. Böylece sürücünün gerçekçi empedansını modelleyebilecekler.
- İletim hattı, başlangıçta ideal (lossless - kayıpsız) bir transmission line olarak modelleniyor. Bu modelde hattın karakteristik empedansı ve gecikme süresi (delay) tanımlı.
- Alıcı taraf ise yüksek empedansa sahip basit bir yük olarak model ediliyor (örneğin 10 Megaohm).
-
Lossy (Kayıplı) Transmission Line Modelleri:
- Gerçek dünyada iletim hatları kayıplıdır, yani iletim sırasında enerji azalır.
- Ancak tüm simülasyon araçlarının ya da modellerinin kayıplı iletim hattı modelleme kabiliyeti aynı değil.
- Örneğin LTSpice’ın kayıplı transmission line modeli sınırlı. QuikcSim, ADS gibi bazı diğer araçlar daha gelişmiş kayıplı transmission line modelleri sunuyor (dielektrik ve iletken kayıpları dahil).
- Simülatör seçerken böyle özellikleri göz önünde bulundurmak önemli.
-
Simülasyonun Önemi ve Esnekliği:
- Bu basit devre ve modelleme yöntemiyle, tasarımcılar “ne olur eğer” (what if) sorularını sorup farklı parametrelerle oynayabilir.
- Örneğin iletim hattının uzunluğu, sinyalin yükselme süresi, kayıp oranı, kaynak-output empedansı gibi değişkenleri değiştirerek yansımaların nasıl değiştiğini görebilir.
- Böylece fiziksel ölçümlere ek olarak simülasyon yardımıyla sinyal bütünlüğü problemlerinin kök nedenleri anlaşılır.
- Bu tip parametre-tabanlı modellere “virtual prototype” (sanal prototip) deniyor.
-
Simülasyonun Basitliği ve Evrenselliği:
- Transmission line modülü (örneğin Spice’da “t line” veya “T-element”) genellikle tüm Spice tabanlı simülasyon araçlarında bulunur.
- Bu sayede simülasyon aracı ne olursa olsun, temel sinyal yansıma problemlerini inceleyebiliyoruz.
Özet: YouTuber burada yüksek hızlı sinyal iletim hattındaki yansıma ve ringing sorunlarını anlamak ve çözmek için, ideal voltaj kaynağı + seri direnç + ideal/gerçekçi transmission line + yüksek empedanslı alıcı modelinin kullanılabileceği temel bir Spice simülasyon ortamı öneriyor. Böylece farklı parametrelerin etkisini sanal ortamda deneyerek gerçek ölçümlerle karşılaştırmak mümkün oluyor.
Eğer bu konuda daha spesifik Spice devre şeması ya da parametre ayarları istersen, onları da açıklayabilirim.
-
- User
daha detaylı anlat ama metne sadık kal. senin extra yorum eklemeni istemiyorum
- Assistant
Tabii, metne sadık kalarak detaylı şekilde anlatayım:
YouTuber burada bir devreyi simüle etmek için modeli kurmaya başlıyor. İlk olarak ekranı temizleyip çizim araçlarını açıyor. Sonra idealleştirilmiş elemanlar kullanarak bir devre çiziyor. Devreyi şu şekilde anlatıyor:
-
Başta ideal bir voltaj kaynağı var. Bu voltaj kaynağı belirli bir başlangıç voltajı ve son voltaj değeri (örneğin 3.3 volt) ile tanımlanıyor. Ayrıca bu voltaj kaynağının belli bir yükselme süresi (rise time) bulunuyor. Bu parametreler kullanıcı tarafından ayarlanabilir.
-
Voltaj kaynağının çıkışında seri bağlantılı tek bir ideal direnç bulunuyor. Bu direnç de parametrik ve değiştirilebiliyor. Böylece çıkış direncini değiştirerek tasarımda farklı senaryolar denenebiliyor.
-
İletim hattı ise başta ideal ve kayıpsız bir transmission line olarak modelleniyor. Bu iletim hattının iki parametresi var: biri gecikme zamanı (delay) ki bu hattın elektriksel uzunluğunu belirliyor, diğeri ise karakteristik empedans (characteristic impedance). Bu parametreler sinyalde yansıma oluşmasının temel nedenlerinden.
-
İletim hattının sonunda ise alıcı modeli yer alıyor. Bu da oldukça yüksek empedanslı (örneğin 10 megaohm) basit bir direnç olarak alınmış.
YouTuber burada ayrıca gerçek uygulamada iletim hatlarının kayıplı olduğunu ve bu nedenle simülasyonlarda kayıplı iletim hattı modellerinin kullanılması gerektiğini belirtiyor. Ancak her simülasyon aracının bu tür gelişmiş modeli desteklemediğini söylüyor. Örnek olarak;
- LTspice’da sunulan kayıplı iletim hattı modeli sınırlı,
- Quicksim gibi araçlarda dielektrik ve iletken kayıpları içeren daha iyi modeller bulunuyor,
- ADS (Advanced Design System) programı da gelişmiş kayıplı iletim hattı modeli içeriyor diyor.
Yani simülasyon yapılacaksa bu modellerin desteklendiğinden emin olmak gerekiyor.
Metinde, başlangıçta lossless (kayıpsız) bir iletim hattı modeli ile başlanabileceği, çünkü bunun simülasyonda sadece "iki nokta arasındaki bağlantı" gibi görüldüğü anlatılıyor.
Şimdi iki parametreye tekrar dikkat çekiliyor:
- Gecikme süresi (delay) — Bu iletim hattının elektriksel uzunluğunu belirler.
- Karakteristik empedans — Bu ise yansımalara neden olan parametre.
Eğer sadece iki nokta arasında doğrudan bir kablo simüle edilirse, yansıma gözlemlenmez. Çünkü empedans farklılığı olmaz.
YouTuber, simülasyonda ölçülecek nokta olarak alıcı tarafı (receiver) seçiyor ve buraya “RX” etiketi koyuyor.
Simülasyonun en basit hali ile:
- Voltaj kaynağı,
- Seri direnç (transmitterin çıkış empedansı),
- Transmission line,
- Yük (yüksek empedanslı alıcı),
kombinasyonu ile çalışacağını anlatıyor.
Burada amaç bu basit modelin neden yansımalar oluştuğunu göstermek.
Simülasyon programlarının çoğunda “t line” adıyla iletim hattı elementi bulunuyor. Bu eleman, voltaj kaynağı ve direnç gibi standart elemanlar kadar evrensel. Spice ağırlıklı simülatörlerin tamamında mevcut.
Bu “t line” elementi simülasyon yaparken sinyaldeki yansıma ve ringing etkilerini öngörür, hesaplar.
Böylece:
- İletim hattının uzunluğunu,
- Sinyalin yükselme süresini,
- Kaynak ve yük empedanslarını,
değiştirip simüle ederek, yansımanın sinyal üzerindeki etkilerini gözlemleyebilirsin.
Simülasyon içinde ölçüm noktası koyabilir, o noktadaki sinyalin şekline (ringing vb.) bakabilirsin.
Bu sayede gerçek devreye fiziksel ölçümler yapmadan önce sanal ortamda birçok “ne olur eğer” senaryosu deneyip tasarım kararları alabilirsin.
YouTuber simülasyon aracının kullanımını özellikle başlayanlar için çok basit ve evrensel bir yöntem olarak gösteriyor.
Özetle: Basit ideal kaynak + seri direnç + ideal veya kayıplı transmission line + yüksek empedans alıcı modeli ile simülasyon kuruluyor. Bu model yansıma ve sinyal bütünlüğü problemlerini anlamak için başlangıç noktası. Simülatörlerde bulunan “t line” elemanı bunun için kritik.
İşte anlattıkları metne birebir bu şekilde sadık kalarak aktarılmıştır.
-
- User
can explore how does the length of the transmission line and the rise time of the signal how does that play a role in the reflection so you can probe the the point over here at the receiver there's a probe point you measure that um with the or you s you display that voltage there you can see the ringing noise you can change the rise time you can change the length you can change the impedance mismatch between the source and the impedance of the line all those things you can play with with this virtual prototype right and that's the starting
00:40:38 place that we used for um for this model and and this is what you get the blue line yeah that's the blue line right and so the red is the simulated result and I I try to so I use individual points here you can see in the um in the measurement or in the display to that's say oh that's measured results each one is a voltage point the scope measures and then the blue is what the simulator tool predicts and and this was based on so in order to do the simulation you have to know okay the level value okay we guess
00:41:13 that you have to know what the rise time is we guessed that based on our estimate nominal value we have to know what the uh Source impedances we guessed that nominal values based on what we thought the output impedance was the characteristic impedence the time delay we guess that and we use 10 megaohms over here for the input so we started out with values based on our best guess that would be dead reckoning if we didn't know anything else here the nominal values that we're going to put in and you know here's what we got not
00:41:44 bad you know what for most applications this would probably be good enough and so dead reckoning is pretty good if you have you know some idea of what to expect in your design well um but you can see well we don't get all of the overshoot we don't get all the undershoot and you know if we had guessed a little wrong and you know the impedance was actually lower probably could have gotten higher values but look we got the 3.3 volts really well eventually um and the damping we kind of got that sort of so it's not that bad a
00:42:17 guess but that's when we guess and now we did two other things the first thing is we looked at that rise time of the signal with the scope and we zoomed in on this Edge so we could measure what was the rise time and we had a good me measure of that then we measured the output impedance of the voltage source and and here's how you do that it's really really simple this guy is on I mean we're only in in the measure we're zooming in this is an half a n this is a uh you know basically a half a microsc we're zooming in but the period was like
00:42:57 100 microsc 10 KZ or so so we had 100 mega mega uh 100 U microseconds how long it lasted and so in this case we looked at this region here where we got the DC value and uh and then we looked at it open which is what this is that's 3.3 volts that tells us what you know if you have a theen circuit there are two terms that characterize it the th and voltage th and resistance we get the th and voltage by looking at the open circuit voltage and then we literally took a resistor and I think we used 50 ohms we connected
00:43:32 a 50 Ohm resistor across the output and we measured the voltage with 50 ohms and so now we have 50 ohms over here we measure the loaded voltage coming out at steady state and we know what this voltage here is we know what this resistance is we know what this voltage is hey it's a voltage divider we can back out what this has to be and so we able to directly measure the output resistance of the driver both in the high State and the low state in the low State you have to add a bias voltage to it but very straightforward to do that so we
00:44:09 directly measure that output th and resistance so now that's not an unknown that's we have confidence in it so we put that value in and now at the receiver so we know enough and one of the exercises I have my students do is we actually literally measure the outp put impedance of a 10x probe with the network analyzer so we measure its impedance profile with frequency and if you know that you can fit a model to it so you know it looks like a a a a nmeg resistor below a kilohertz and it looks like a 10 POF farat capacitor you know
00:44:46 up to couple hundred megaherz so we know the model for our 10x probe and so we put that in so we took this and we said okay I know what this is but you know what there's also a 10 puff capacitor over here and so we put that in and so we know what this is it's not a variable anymore we know what the rise time is it's not a variable anymore we know the voltage is it's not a variable anymore we know what the um the the probe is over here and then we said okay you know what I'm going to look at what the impedance of this line is so um we in
00:45:25 order to calculate if I know the geometry in order to calculate the characteristic impedance I need to know also the linewidth and the dialectric thickness but I have to know the dialectric con of the material and so you know part of what we do in our in our class is we build test boards that we send to our event we use jlc PCB um we and and we use um uh uh PCB way um and we send them test boards we get them back test boards that are designed to measure the dialectric constant and we could do that on another presentation
00:45:57 because this really simple technique and and it gives you a very good very quick easy measurement that can be done with very simple equipment and so we measure the dilet and we know it's 4.9 for the two- layer board when you have a core uh core it's 4.9 4.9 and so now oh now we don't have to guess the dialectric we know what it is we know what the linewidth is we know what the thickness is now and and we know the length because we just you know count this the the length in alum in the design tool and so we know what the linewidth we
00:46:30 know what the length is we know the stackup we know the material properties no guessing anymore we just put those numbers in here and we used a lossy transmission line model so we could vary the the the most important term that influences loss in a transmission line is the uh dissipation factor of the material and so we could make that a I didn't know what it was I I know what it is but in in this example here we were going to make that a variable to see what its impact was and so we added a lossy transmission line model that had the DF
00:47:05 as a term in there and we started out we said okay let's turn off the DF and just see do does it matter does it play a role in this simulation so again one of the principles in any measurement simulation correlation is always start with the simplest model possible that has the features you want and then if you can't get a good match then build complexity in there that's why we started out with um uh no capacitor over here and no loss over here simple and and so we we turned it on and oops wrong one so basically DF is the
00:47:42 only one which only unknown variable in yeah all and there's also the resistance loss in the line and we could turn that off as well um but I I have enough experience that you know the dis at these frequencies the um the dissipation factor is is an important term um oops wrong one doing the wrong way here we go and so this was dead reckoning just best guess what we thought and then we made those changes and all we did we used the output impedance that we measured directly we used the input capacitance of the scope probe we measured
- Assistant
Bu bölümde YouTuber, transmisyon hattındaki yansıma olayını ve simülasyon ile ölçüm sonuçlarının karşılaştırılmasını detaylı anlatıyor. Aşağıda metne sadık kalarak adım adım açıklıyorum:
-
Model ile Parametrelerin İncelenmesi:
- Transmisyon hattının uzunluğunun ve sinyalin yükselme süresinin (rise time) yansımalar üzerindeki etkisi inceleniyor.
- Alıcı tarafındaki (receiver) bir ölçüm noktası simülasyonda belirleniyor.
- Bu noktada voltaj ölçülebiliyor ve ölçüm sonuçlarında ortaya çıkan “ringing” (dalgalanma) gözlemlenebiliyor.
- Modelde sinyalin yükselme süresi, hattın uzunluğu, kaynak ile iletim hattı arasındaki empedans uyumsuzlukları gibi parametreler değiştirilebiliyor.
- Böylece sanal prototip üzerinde çok sayıda “what if” (ne olur eğer) denemesi yapılabiliyor.
- Bu, problemin temelinde nelerin olduğunu anlamak için başlangıç noktası.
-
Ölçüm ve Simülasyon Sonuçlarını Karşılaştırma:
-
Ölçülen sonuçlar mavi çizgiyle gösteriliyor; simülasyon sonuçları ise kırmızı renkle.
-
Ölçüm noktaları tek tek alınan gerilim değerleri (scope ile direkt ölçülen voltajlar).
-
İlk olarak simülasyon için parametrelerin ne olacağı bilinmiyor, tahminle (guess) nominal değerler konuluyor; örneğin:
- Voltaj seviyesi (ör: 3.3V),
- Yükselme süresi tahmini,
- Kaynak çıkış empedansı tahmini,
- Karakteristik empedans ve zaman gecikmesi tahmini,
- Alıcı direnci olarak 10 megaohm.
-
Bu tahminle “dead reckoning” (deneme-yanılma veya kaba tahmin) yöntemi uygulanıyor.
-
Tahmin ile simülasyon çıktısı ölçüme oldukça yakın çıkıyor; tam olarak overshoot ve undershoot yakalanamasa da nispeten başarılı.
-
Yani klasik mühendislik pratiğinde, eğer belirli tasarım bilgisi varsa (örneğin empedanslar, yükselme süreleri veya kablo uzunlukları), tahminle çalışmak çoğu durumda yeterli olabilir.
-
-
Parametrelerin Doğrudan Ölçülmesi ve Model Güncellemesi:
- Sinyalin yükselme süresi, osiloskopla sinyalin başlangıç kenarı detaylı zoom yapılmak suretiyle ölçülüyor.
- Kaynak çıkış direnci (output impedance) ölçülüyor. Bu ölçüm çok basit:
- Önce çıkış “açık devre” durumundaki voltaj ölçülüyor (ör: 3.3V).
- Sonra çıkışa bilinen (örneğin 50 ohm) bir direnç bağlanıyor.
- Direnç ile yüke bağlı olarak çıkıştaki voltaj belirleniyor.
- Bilinen gerilim bölücü (voltage divider) ilişkisi kullanılarak çıkış direnç değeri hesaplanıyor.
- Böylece Thevenin eşdeğer çıkış gerilimi ve çıkış direnci doğrudan ölçülmüş oluyor.
-
Prob (scope probe) Modelleme:
- Öğrencilere verilen bir başka uygulama, 10x osiloskop probunun çıkış empedansını network analizörü ile ölçmek.
- Empedansın frekansa bağlı değişimi ölçülüyor.
- Bu sayede probun modeli oluşturuluyor: 1 kHz altındaki frekanslarda yaklaşık 1 megaohm direnç, 100 MHz civarında yaklaşık 10 pF kapasitans içerdiği anlaşılıyor.
- Prob modeli, simülasyona gerçekçi olarak katılıyor.
-
İletim Hattı Parametrelerinin Belirlenmesi:
- Karakteristik empedans hesaplamak için hattın geometrisi (ör: çizgi genişliği), dielektrik kalınlığı ve malzemenin dielektrik sabiti (dielektrik const) bilinmeli.
- Test panoları (test board) hazırlanıp örneğin JLCPCB veya PCBWay üzerinden üretip dielektrik sabiti ölçümü yapılabiliyor.
- Ölçülen dielektrik sabiti yaklaşık 4.9 bulunmuş.
- Ayrıca tasarım aracında karta ait uzunluk, malzeme kalınlığı gibi bilgiler net olarak alınıyor.
- Böylece artık hiçbir parametre “tahmin” değil, “ölçülmüş ve bilinen” değer oluyor.
-
Kayıplı (Lossy) Transmission Line Modeli:
- İletim hattının “dissipation factor” (DF) yani malzeme kayıpları simülasyona ekleniyor.
- DF simülasyondaki en önemli bilinmeyen parametre olarak tanımlanıyor.
- Başlangıçta DF kapatılarak (DF=0) simülasyon yapılıyor, böylece kayıpların etkisi gözlemleniyor.
- Ek olarak hattaki dirençsel kayıplar da varsayılan olarak eklenip çıkarılabiliyor.
- Tecrübe ile dissipation factor’ın (malzeme kayıplarının) özellikle yüksek frekanslarda önemli olduğu vurgulanıyor.
-
Simülasyonda Alınan Sonuçlar ve Güncellemeler:
- Başlangıçta verilen “dead reckoning” yani tahmini değerlerle başlayan simülasyon,
- Sonrasında ölçülen çıkış empedansı, prob kapasitansı, yükselme süresi gibi gerçek parametrelerle güncelleniyor.
- Böylece simülasyon ile gerçek ölçümlerin tutarlılığı artırılıyor.
Özetle, bu bölümde YouTuber:
- Transmisyon hattı ve sinyal parametrelerinin yansımalar üzerindeki etkisini simülasyonla inceliyor.
- Simülasyon parametrelerini önce tahminle koyup ardından gerçek ölçümlerle doğrulayıp güncelliyor.
- Prob empedansı, çıkış direnci, dielektrik özellikler gibi parametreleri ölçerek simülasyon modeline gerçekçi şekilde entegre ediyor.
- Malzeme kayıplarının (dissipation factor) etkisini de modelleyip simülasyondaki yansıma ve sönümlenme davranışlarının gerçekçi olmasını sağlıyor.
Bu metin, gerçek tasarım mühendisliğinde ölçüm ve simülasyonun beraber nasıl kullanıldığını, deneysel verilerle simülasyonların nasıl doğrulandığını ve geliştirdiğini net bir şekilde ortaya koyuyor.
-
- User
It is important to clarify this aspect of LTspice. The software simulates noise that is intrinsic to components using the noise-type simulation. This type of simulation is suitable to verify the functionality of a circuit such as an analog filter. For EMC purposes, we need to simulate common-mode and differential-mode noise, so we can be sure that our filters are effective for filtering both noise types.↳
The following circuit is an EMC filter comprised of capacitors and a common-mode choke to attenuate common-mode noise (C2, C3, L3). It also includes two inductors and capacitors to attenuate the differential noise (L1, L2, C1, C4).
- Assistant
LTspice programının önemli bir özelliği, bileşenlerin içsel (intrinsic) gürültülerini “noise-type” simülasyonlarla modelleyebilmesidir. Bu “noise” simülasyon türü, analog filtre gibi devrelerin işleyişini doğrulamak için uygundur.
Ancak, EMC (Elektromanyetik Uyumluluk) amaçları için sadece bileşen kaynaklı gürültü yeterli değildir; ortak mod (common-mode) ve diferansiyel mod (differential-mode) gürültüleri de simüle edebilmemiz gerekir. Böylece filtrelerimizin her iki gürültü tipini de etkin şekilde bastırdığından emin olabiliriz.
Örnek devrede bir EMC filtresi gösterilmiştir. Bu filtre şu elemanlardan oluşmaktadır:
-
Ortak mod gürültüsünü azaltmak için kullanılan elemanlar:
- Kapasitörler C2 ve C3
- Ortak mod choke (bobin) L3
-
Diferansiyel gürültüyü azaltmak için kullanılan elemanlar:
- İki küçük endüktör L1 ve L2
- Kapasitörler C1 ve C4
Bu yapı, ortak mod ve diferansiyel mod gürültülerini ayrı ayrı hedefleyerek etkili bir EMC filtresi oluşturur.
Sonuç olarak, LTspice’da EMC için doğru simülasyon yapmak adına ortak mod ve diferansiyel mod gürültülerin uygun şekilde modellenmesi gereklidir ve filtre tasarımında bu gürültü türlerine karşı ayrı elemanlar kullanılır.
-
- User
To simulate a protective earth (PE) or a chassis connection, we use a potential that is coupled through a very small capacitance to the regular ground or negative potential.
- Assistant
Bir koruyucu toprak (Protective Earth - PE) veya şasi bağlantısını simüle etmek için, bu PE veya şasi potansiyelini, çok küçük bir kapasitans aracılığıyla normal toprak (ground) veya negatif potansiyale bağlarız (couple ederiz).
Yani, PE veya şasi doğrudan toprakla kısa devre yapılmaz; bunun yerine çok küçük bir kapasitans üzerinden bağlanır. Bu modelleme yöntemi, gerçek devrelerde topraklama ve şasi arasındaki kapasitif kaplamaları ve bant genişliği gibi etkileri daha doğru yansıtmak için kullanılır.
- User
The frequency response of the ideal filter falls smoothly as frequency increases, but the real filter does not exhibit the same behavior. Starting at approximately 40 kHz, it produces less attenuation than the ideal filter. Hence, we can see that performance changes considerably when we approximate a real environment.
- Assistant
İdeal filtrenin frekans cevabı, frekans arttıkça düzgün ve kesintisiz bir şekilde düşerken; gerçek filtre aynı davranışı göstermez. Yaklaşık 40 kHz’den itibaren, gerçek filtre ideal filtreye kıyasla daha az zayıflatma (attenuation) sağlar.
Bu nedenle, gerçek ortamı yaklaşık olarak modellediğimizde filtrenin performansının önemli ölçüde değiştiğini görebiliriz.
- User
18- 36Vin, Pout=75W, η=%75 verim ve Fsw=100KHZ için EMI filtre tasarlanmak istensin.
-
DC/DC çevirici giriş direnci (Rin) hesaplanır: Rin=Vinmin/Iinmax=Vinmin^2η/Poutmax=3240,75/75=3,24 Ω
-
Girişe yansıyan temel harmonic değer (I1) hesaplanır: Iavg=Pout/(Vinminη)=75V (18V0,75)=5,56A Duty Cycle verilmediğinde %50 alınır. Ipeak=11,12A olur (2Iavg). I1 temel harmonic=0,636Ipk=7,08A
-
İhtiyaç duyulan zayıflatma oranı (Att) hesaplanır: Iref=1miliA (veya dB karşılığı) yansımaya izin verilecekse, Att=I1/Iref=7,08A/0,001A=7080 (77dB)
-
Zayıflatmayı sağlayacak DM LC EMI filtre alt kesim fr (Ff) hesaplanır: Att=(Fsw/Ff)^2=7080=(100Khz/Ff)^2 Ff=1188Hz.
-
DM LC EMI filtre Cf ve Lf elemanlarının değeri hesaplanır: Ff=1/(2piRinCf)=1188=1/(23,14153,24Cf) ise Cf=41,35uF. Ff=Rin/(2piLf)=1188=2,34/(23,1415Lf) ise Lf=434uH.
-
DM LC EMI filtre damp elemanları (Cd, Rd) hesaplanır. Cd≥4Cf=160uF. Ff için ZCd<Rd kalmalı. Rd>1/(23,14151188160uF)=0,8 Ω. Zo=√(L/C=√(434uH/41,35uF)=3,24 Ω. n=Cd/Cf≈4 ise. Rd=Z0(√[((2+n)(4+3n))/2n^2(4+n)] =3,24(√[(616)/(328)])=3,24*0,6123≈2 Ω. ZCd(0,8Ω)<Rd(2 Ω) şartı sağlanır. daha ddetaylı açıkla
-
- Assistant
Elbette, verdiğiniz EMI (Elektromanyetik Girişim) filtre tasarımı adımlarını daha detaylı ve açıklayıcı şekilde anlatayım.
Verilenler:
- Vin = 18 - 36 V (giriş gerilimi aralığı)
- Pout = 75 W (çıktı gücü)
- η = %75 (verimlilik)
- Fsw = 100 kHz (anahtarlama frekansı)
1) DC/DC çevirici giriş direnci (Rin) hesaplanması
Amaç: Giriş tarafında görülen eşdeğer direnç değerini hesaplamak.
Formül:
[ R_{in} = \frac{V_{in(min)}^2 \times \eta}{P_{out(max)}} ]
Burada:
- (V_{in(min)} = 18V) (minimum giriş gerilimi)
- (\eta = 0.75) (verimlilik)
- (P_{out(max)} = 75W) (maksimum çıkış gücü)
Hesaplama:
[ R_{in} = \frac{18^2 \times 0.75}{75} = \frac{324 \times 0.75}{75} = \frac{243}{75} = 3.24, \Omega ]
Yani, güç kaynağı girişinde yaklaşık 3.24Ω’luk bir direnç görülür.
2) Girişe yansıyan temel harmonik akım (I1) hesabı
Öncelikle:
-
Ortalama (ortalama) giriş akımı (I_{avg}): [ I_{avg} = \frac{P_{out}}{V_{in(min)} \times \eta} = \frac{75}{18 \times 0.75} = 5.56A ]
-
Yükselme, pik akımı (I_{peak}) (Duty Cycle bilinmediği için %50 alınır): [ I_{peak} = 2 \times I_{avg} = 2 \times 5.56 = 11.12 A ]
Temel harmonik akımı (1. harmonik, (I_1)):
Sinüzoidal bileşene dönüşüm katsayısı:
[ I_1 = 0.636 \times I_{peak} = 0.636 \times 11.12 = 7.08 A ]
3) Gerekli zayıflatma oranı (Att)
Sinyalin yansıma sonucu oluşan parazitik akım büyüklüğü (kabul edilebilir referans):
[ I_{ref} = 1 mA = 0.001A ]
İstenilen zayıflatma oranı hesaplanır:
[ Att = \frac{I_1}{I_{ref}} = \frac{7.08}{0.001} = 7080 ]
Desibel (dB) karşılığı:
[ 20 \log_{10}(7080) \approx 77, dB ]
4) EMI filtresinin alt kesim frekansı (F_f) (damping frekansı)
Zayıflatma, EMI filter frekansına bağlı olarak:
[ Att = \left(\frac{F_{sw}}{F_f}\right)^2 ]
Buradaki bilinmeyen (F_f) 'dir.
Verilen:
[ Att = 7080, \quad F_{sw} = 100,kHz ]
[ 7080 = \left(\frac{100000}{F_f}\right)^2 \Rightarrow F_f = \frac{100000}{\sqrt{7080}} \approx 1188, Hz ]
Bu frekans, filtre tasarımının temel alt sınır frekansı olarak alınır.
5) EMI filtre elemanlarının (Cf ve Lf) hesaplanması
Kapasitör (C_f) hesaplama:
Filtre alt kesim frekansı formülünden:
[ F_f = \frac{1}{2 \pi R_{in} C_f} \Rightarrow C_f = \frac{1}{2 \pi R_{in} F_f} ]
Değerleri koyarsak:
[ C_f = \frac{1}{2 \pi \times 3.24 \times 1188} = \frac{1}{24150} = 41.35 \times 10^{-6} F = 41.35 \mu F ]
Endüktans (L_f) hesaplama:
Formül:
[ F_f = \frac{R_{in}}{2 \pi L_f} \Rightarrow L_f = \frac{R_{in}}{2 \pi F_f} ]
Burada R(_{in}) ile verilen değer uyumsuz görünüyor, metindeki hesaplama şu şekilde:
[ L_f = \frac{R_{in}}{2 \pi F_f} = \frac{3.24}{2 \pi \times 1188} = \frac{3.24}{7466} = 0.000434 H = 434 \mu H ]
6) Damping elemanlarının (Cd, Rd) hesaplanması
Cd hesaplama:
Damping kapasitesi minimum
[ C_d \geq 4 \times C_f = 4 \times 41.35 \mu F = 165.4 \mu F \approx 160 \mu F ]
Rd için alt sınır:
Damping frekansında, kondansatörün empedansı (Z_{Cd}) Rd'den küçük olmalı:
[ Z_{C_d} = \frac{1}{2 \pi F_f C_d} ]
Bu yüzden:
[ R_d > Z_{C_d} = \frac{1}{2 \pi \times 1188 \times 160 \times 10^{-6}} = 0.83 \Omega \approx 0.8 \Omega ]
Z(_0) karakteristik empedans hesaplaması:
[ Z_0 = \sqrt{\frac{L_f}{C_f}} = \sqrt{\frac{434 \times 10^{-6}}{41.35 \times 10^{-6}}} = \sqrt{10.5} = 3.24 , \Omega ]
Damping direnç (R_d) hesaplama formülü:
[ R_d = Z_0 \times \sqrt{\frac{(2 + n)(4 + 3n)}{2 n^2 (4 + n)}} ]
Burada (n = \frac{C_d}{C_f} \approx 4)
Hesaplama adımları:
İçerideki ifade;
[ \frac{(2 + 4)(4 + 3 \times 4)}{2 \times 4^2 \times (4 + 4)} = \frac{6 \times 16}{2 \times 16 \times 8} = \frac{96}{256} = 0.375 ]
Karekökü:
[ \sqrt{0.375} = 0.6123 ]
Son olarak:
[ R_d = 3.24 \times 0.6123 = 1.983 \approx 2, \Omega ]
Kontrol şartı:
[ Z_{C_d} = 0.8, \Omega < R_d = 2, \Omega ]
Bu şart sağlanmıştır, yani damping direnç değeri uygun.
Özet ve Yorum
- Giriş direnci yaklaşık 3.24Ω olarak belirlendi.
- Temel harmonik akım 7.08A olup, 1mA hedefli yansıma ile karşılaştırıldığında 77dB zayıflatma gerekiyor.
- Filtrenin alçak kesim frekansı 1188 Hz olarak bulundu.
- Kapasitör ve endüktans sırasıyla 41.35μF ve 434μH seçildi.
- Damping devresi için kapasitör 160μF ve direnç yaklaşık 2Ω hesaplandı.
- Damping elemanları koşulları sağlıyor ve devre stabil şekilde tasarlandı.
Bu hesaplamalar EMI filtresinin temel tasarım parametrelerini belirler, filtre elemanları bu değerlerde seçilip devreye uygulanabilir. Tasarım sürecinde bu yöntem, filtre performansını hedeflenen zayıflatma değerine ulaştırmak için gereklidir.