ground bounds and i'm gonna increase the scale here but big difference like huge…
- User
ground bounds and i'm gonna increase the scale here but big difference like huge difference big difference right you can see here they're on the same scale uh a volt per division dramatic reduction so here i've increased the scale and we still have a lot of ground mounts i mean we have 400 millivolts and to 500 we still have a volt peak to peak of ground bounds here but it's dramatically less than the four volt peak peak that we had before okay so this says yeah use separate returns but you're still going to have a
00:41:46 lot of ground bounds now let's switch the board and so we'll keep the same code running and so now we come over here this is a solid return there's nothing to switch we have all these i o switching and then we're going to have this victim line and the victim line these all have i don't know if you can see there's little vias here the returns go to the plane underneath and this victim line is shorter to the plane underneath and so we just have this little loop here going down and then back through the return plane okay
00:42:15 so let's switch it over and now let's go to uh let me show you i'm gonna i'm gonna connect in the signal pin here and um let's go let's go take a look at that so here's pin 13 that's and we see them see remember we're increasing the number of i o switching each each cycle and now we'll look at the noise on the victim line and i'm going to connect in the victim line over here okay and let's see what we got and here's the noise in the victim line and you can see you know what they're still ground bounce over there i'm sorry there's
00:43:06 still noise there's still crosstalk when the ios are far away dramatically reduced but look when we get really close is this different kind of crosstalk this is like real crosstalk uh this is not ground bounds but this is the crosstalk right and and i i call it it's not ground balance because we have a nice wide continuous plane but we still have capacity and inductive coupling and um now i have these on the difference picked up from the trace which is routed on the top uh the aggressor the trace on the top is uh making all these noise around it and
00:43:44 the other one is picking it up because so we have close to both right we have both capacitive and inductive coupling and but you know look we have a loop here signal and the return is the plane underneath that's still a loop and we've got a loop over here so there's still inductive crosstalk and so we're still going to see crosstalk but it's going to be dramatically less and let's just see you know this is when they're all switching and you can see boy it really increases uh getting closer we're gonna run the
00:44:13 sequential one only the last one is like biggest one right and we'll see why that is in a second let's i'm gonna put them on the same scales over here um let's see so they're on one volt per division and let's see if i can move it over here if we can see it that'll be really hard to see so let's see i'm gonna maybe you can move them like make them separate well here here we go so the pink is what we had with a separate return and they're on the same scale and the the um the bright one is the the crosstalk with um uh the solid return and and so here's
00:44:56 what i'm going to increase the scale for both of the oops for both of them got to um so you do this one first okay that's 100 millivolts of division then i'm going to increase this guy's scale to the same okay so they're on the same scale 100 millivolts per division the light pink was what we had with the um uh the the separate return but still on the top surface and the the bright pink is the one with the the plane so it's dramatic you know reduced there's still crosstalk there now uh we're going to try one other little
00:45:41 experiment here so remember here's the crosstalk this is with all of them switching simultaneously let's make them sequential in other words we're going to switch one at a time but we're going to move them closer and we'll look to see what is the impact of turning this one on look at the crosstalk from this one on the victim this one this one this one and what do you expect to see what do you think you're gonna see i think the last one will be like the most visible and all the other will be very much very good i
00:46:16 would expect exactly the same thing so let's see where we're at with it compiling compiling compiling and here we go turn it off turn it on and sure enough look at that so here is the last one here's here are the ones far away switching yeah okay there's a little bit remember 100 millivolts of division here a little bit of switching noise a little bit a little bit oh dramatic increase because of the proxy and all this uh dramatic increase is because the uh noise is transferred also through the air and and the dielectric it's not
00:46:58 it's not the shared path which is causing major majority it's the magnetic field lines from the two loops that are spatially separated there's still field lines between them it's not a lot i mean it's you know 200 millivolts peak to peak or so compared to 4 volts peak to peak that we were seeing before so it's nice it's nice to see that now there is there is the effect going through the air basically or medium or something right exactly so the lesson from all this is number one if you want to reduce ground balance don't use a shared return path
00:47:39 if you do make it as short as practical and you always want to route the board with a solid return now this is you know in in the world of signal ontario we say there are three families of problems to worry about there's signal integrity there's power integrity and there's emi ground balance is one of those topics that holistically interacts with all three of those we've only been looking here at the signal integrity part and crosstalk but the same mechanism that causes ground balance because like you said you
00:48:14 get these field lines around the air well they don't stay just on the board they can expand outward and it's the ground balance from a screwed up return path that generally can create the largest range uh magnetic field changing changing magnetic fields and that contributes to you get you see it as near field and that can expand to far field and that's where you feel fcc and so if you have ground bounce on your board chances are you number one have near field emissions and probably far-field emissions as well and that's why and so you want to reduce
00:48:52 ground bounce for reducing crosstalk you also want to reduce ground balance in order to reduce rated emissions and that's why when you're designing a board never ever route the signals all over the board top and bottom layers and then when you're done copper fill on the top and copper fill on the bottom thinking that oh you've done all the you created all the return paths and you're and you're done worst thing you could possibly do you want to select the uh adjacent layer as a ground solid return and you want to route the signals
00:49:23 and mix signal power on the other layer and that's the approach that i recommend as a starting place because that'll reduce the signal quality problems noise it'll reduce crosstalk uh it'll reduce emi so how is it possible that the old boards you know with many gates on two layer around it how is it possible they worked oh the connectivity no problem connectivity is great and in this particular microcontroller board which is designed kind of that way of random connections on the top and bottom in copper fill that the noise margin for this microgram
- Assistant
It sounds like you're describing an in-depth demonstration and explanation about ground bounce, ground bounce reduction techniques, and crosstalk in PCB layouts using a microcontroller with multiple I/O switching lines. Here's a summarized explanation of the key points and lessons from your provided transcript:
Key Topics Discussed:
-
Ground Bounce and Its Impact:
- Ground bounce occurs when simultaneous switching of multiple I/O pins causes the return ground reference to shift momentarily, creating noise (up to several volts peak-to-peak in some cases).
- Using separate return paths helps but does not entirely eliminate ground bounce.
-
Improving Return Path to Reduce Noise:
- Using a solid return plane (a continuous ground plane layer) significantly reduces ground bounce — from several volts peak-to-peak to about hundreds of millivolts.
- Having a short and low-inductance return path is essential to keep ground bounce minimal.
-
Crosstalk Between Nearby Traces:
- Even with a solid ground plane and improved return path, crosstalk remains due to capacitive and inductive coupling between closely spaced signal lines.
- This coupling causes noise on nearby ("victim") lines, but it is much less severe than ground bounce caused by poor return paths.
- Crosstalk appears as induced signals on nearby traces due to electromagnetic field coupling, including magnetic loops formed by the signal and return currents.
-
Effect of Switching Multiple Lines Sequentially:
- When lines are switched sequentially rather than all at once, crosstalk noise on the victim line is noticeably different.
- The noise caused by the last closest switching line is most significant because of proximity and stronger magnetic coupling.
- Noise propagates not only through PCB coupling but also through space (air or dielectric), emphasizing near-field electromagnetic emissions.
-
EMI, Signal Integrity, and Power Integrity:
- Ground bounce and return path design affect:
- Signal integrity (clean data signals, minimal interference),
- Power integrity (stable, low noise power and ground),
- Electromagnetic interference (EMI) emissions.
- Poor ground return paths tend to increase magnetic field emissions, leading to near-field and far-field radiation picked up in EMI measurements (e.g., FCC compliance).
- Ground bounce and return path design affect:
-
Design Recommendations:
- Always use a solid return plane layer adjacent to the signal layer to provide a low-inductance return path.
- Avoid routing signal return currents via shared or split ground paths. If separate returns are used, keep them as short and direct as possible.
- Do not rely solely on copper fill or stitching on the signal layer to create return paths. This is insufficient.
- Keep signal traces and return planes closely coupled to minimize loop area, which reduces inductive coupling and emissions.
- Route mixed signal and power layers either on separate layers or well-isolated to reduce crosstalk.
- Recognize the trade-off between PCB complexity and signal noise; some old or simpler boards worked despite these issues due to inherent design margins and slower switching.
Summary
To minimize ground bounce and crosstalk in your PCB designs:
- Use solid, continuous ground planes underneath signal layers to provide a low-inductance return path.
- Keep return paths short and direct, avoiding split or shared return currents when possible.
- Recognize that crosstalk will still exist due to unavoidable capacitive and inductive coupling, but good return path design reduces it dramatically.
- Understand that noise also propagates via near-field magnetic coupling, not just via PCB traces.
- Optimize routing practices—do not just rely on copper pour or stitching on signal layers to return current.
- Follow these practices to improve signal integrity, power integrity, and reduce EMI emissions for more robust and compliant designs.
If you need help implementing these recommendations with specific PCB layout tools or want practical examples or simulations, feel free to ask!
-
- User
bana türkçe olarak anlat metindekini
- Assistant
Tabii! Aşağıda, verdiğin uzun metnin Türkçe özeti ve ana noktaları yer almaktadır:
Ana Konular:
-
Ground Bounce (Toprak Sıçraması) Nedir ve Neden Önemlidir?
- Çok sayıda çıkış (I/O) pini aynı anda anahtarlanınca, toprak hattında ani voltaj değişimleri oluşur. Buna "ground bounce" denir. Bu durum, sinyallerde gürültü yaratır ve sinyal kalitesini düşürür. Örneğin önce voltlar seviyesinde olan bu gürültü, uygun önlemlerle yüzlerce milivolta kadar indirilebilir.
-
Ground Bounce’u Azaltmak İçin Ne Yapmalı?
- Ayrı ayrı toprak dönüş yolları kullanmak bir nebze yardımcı olur ama yeterli değildir.
- En etkili yöntem tam ve sürekli bir toprak (ground) plane katmanı kullanmaktır. Bu sayede toprak dönüş yolu çok daha kısa ve düşük endüktanslı olur, böylece ground bounce önemli ölçüde azalır.
-
Kros Talk (Gürültü Etkileşimi) Nedir?
- Toprak plane olsa bile, yakın sinyal hatları arasında kapasitif (elektrik alanı ile) ve endüktif (manyetik alan ile) etkileşimden kaynaklanan sinyal gürültüsü (crosstalk) olur.
- Bu, hasar vermese de, az da olsa sinyal hatlarına müdahale eder.
-
Birbirine Yakın Hatlarda Ardışık Anahtarlamanın Etkisi
- Tüm hatlar aynı anda anahtarlanırsa oluşan krosstalk fazla olur.
- Sıralı olarak ve birer birer anahtarlanırsa, en yakın hatın etkisi en fazla olsa da toplam gürültü düşer.
- Gürültü sadece PCB üzerinden yayılmaz, hava yoluyla da elektromanyetik alanlar aracılığıyla bir hat diğerini etkileyebilir.
-
EMI ve Tasarımın Diğer Etkileri
- Toprak sıçraması ve dönüş yolunun kötü tasarımı, sadece sinyal kalitesini değil, aynı zamanda elektromanyetik girişim (EMI) sorunlarını da artırır.
- Bu nedenle toprak ve sinyal yollarının iyi planlanması, FCC gibi standartlara uygun elektromanyetik uyumluluk için önemlidir.
-
İyi PCB Tasarım Tavsiyeleri
- Sinyal hatları için altlarında kesintisiz ve geniş toprak plane kullanın.
- Toprak dönüş yollarını paylaşmayın veya kopuk yapmayın, mümkünse en kısa mesafede ve aynı katmanda toprak dönüşü sağlayın.
- Sinyal hatlarını ve toprağı rastgele üst ve alt katmanlara yayıp ardından sadece üst ve altta bakır dolgusu yapmak işe yaramaz.
- Sinyal ve güç hatlarını ayrı katmanlarda veya iyi izole edilmiş şekilde yerleştirin.
- Bu yaklaşımlar, sinyal gürültüsünü, krosstalk’u ve elektromanyetik yayılımı önemli ölçüde azaltır.
-
Eski Tasarımlar Nasıl Çalışıyordu?
- Daha basit, 2 katmanlı eski kartlarda, yavaş anahtarlama ve geniş tolerans nedeniyle bu sorunlar fazla hissedilmezdi. Ancak modern yüksek hızlı tasarımlarda bu konular kritik hale geldi.
Özet:
PCB tasarımında toprağın ve sinyalin dönüş yollarını iyi planlamazsan:
- Toprak sıçraması (ground bounce) yüksek olur, sinyaller bozulur.
- Krosstalk artar, yakın sinyal hatları birbirini etkiler.
- Elektromanyetik girişim (EMI) yükselir, bu da radyo parazitlerine yol açabilir ve standartlara uymada problem yaratır.
Bunun için:
- Kesintisiz, geniş ve sağlam bir toprak plane kullan.
- Sinyal ve toprak yollarını yakın ve kısa tut, dönüş akımlarını asla rastgele dağıtma.
- Sinyal ve güç katmanlarını ayırarak crosstalk ve paraziti azalt.
- Yalnızca üst ve alt katmana bakır doldurup işi bitmiş sanma, iyi planlama şart!
Eğer daha detaylı anlatım, örnek çizimler veya pratik öneriler istersen, yardımcı olmaya hazırım.
-
- User
senden yorumlamanı istemiyorum metni açıklamanı istiyorum ne anlattığını
- Assistant
Tabii, metnin anlattıklarını açıklayıcı, yorum yapmadan, doğrudan anlatayım:
Metin, elektronik devre kartlarında (PCB) özellikle çok sayıda giriş/çıkış pini (I/O) aynı anda anahtarlanınca ortaya çıkan ground bounce (toprak sıçraması) ve krosstalk (parazit, gürültü etkileşimi) problemlerini anlatıyor.
- Başlangıçta, ayrı ayrı toprak dönüş yolları kullanıldığında bile, hala hatlar arasında voltaj dalgalanmaları (ground bounce) görülüyor ama bu dalgalanmalar voltları bulmuyor, daha düşük seviyede oluyor.
- Bunu göstermek için bir karta bakılıyor; burada “kurban” (victim) olarak adlandırılan gürültü alan bir sinyal hattı var. Bu hattın toprak dönüşü düz bir toprak (ground plane) üzerinden kısa bir yol kat ediyor, bu da minimal bir döngü oluşturuyor.
- Sinyal ve dönüş yolları arasındaki döngü küçük tutulduğunda ground bounce azalıyor ancak genellikle ortadan kalkmıyor, çünkü hem kapasitif hem de endüktif (manyetik) coupling (etkileşim) sürdüğü için hatlar arasında halen parazit oluşuyor.
- Bu parazit, sinyal hattına yakın anahtar konumdaki diğer I/O hatlarından kaynaklanıyor. Özellikle yakın olan anahtar hattı, daha uzak hatlara göre daha fazla gürültü yaratıyor.
- Bu parazit mekanizması sadece paylaşılan dönüş yoluyla değil, aynı zamanda elektromanyetik alanların yayılması yoluyla da oluyor, yani gürültü havadan (dielektrik ve hava ortamı) da yayılıyor.
- Ölçümlerde belirlenen gürültü seviyesi birkaç yüz milivolt civarında, önceki birkaç voltluk ground bounce seviyesinden çok daha düşük.
- Gürültü sırasıyla tüm hatlar aynı anda anahtarlandığında yüksek, tek tek anahtarlandığında ise daha düşük ve özellikle en yakın hatın etkisi daha fazla oluyor.
- Buradan çıkarılan dersler:
- Ground bounce’u önlemek için mutlaka paylaşılan dönüş yolu yerine mümkün olduğunca kısa ayrı dönüş yolları kullanmak gerekiyor.
- Dönüş yollarının mümkün olduğunca geniş, sürekli ve katman olarak sinyal katmanı yakınındaki bir solid (kesintisiz) toprak plane olması lazım.
- Elektronik tasarımda genellikle 3 ana problem alanı vardır: sinyal bütünlüğü, güç bütünlüğü ve elektromanyetik girişim (EMI). Ground bounce ve döngü alanları bu üçüne de etki eder.
- Ground bounce kaynaklı parazit alanları kart dışına yayılabilir ve hem yakın alan hem de uzak alan elektromanyetik dalgalanmalara neden olabilir. Bu da FCC gibi standartların ihlal edilmesine yol açar.
- Bu nedenle, devre kartı tasarlarken sinyal hatlarının dağınık ve rastgele üst-alt katmana serpiştirilip sonradan bakır dolgusu yapılması iyi bir yöntem değildir.
- Doğru yöntem, bir katmanı kesintisiz toprak katmanı olarak ayırmak ve sinyal ile güç hatlarını diğer katmanlarda uygun şekilde konumlandırmaktır.
- Son bölümde, eski kartların nasıl çalıştığı sorusuna değiniliyor; eski düşük hızlı ve az kaynaklı kartlarda bu sorunlar çok hissedilmezken, günümüz hızlı ve yoğun kartlarda mutlaka bu prensiplere dikkat etmek gerekiyor.
Kısaca metin, PCB üzerindeki toprak dönüş yollarının önemi, ground bounce ve crosstalk oluşum mekanizmaları, elektromanyetik sorunları ve bu problemlerin çözümüne yönelik temel tasarım prensipleri hakkında teknik bir anlatımdır.