Skip to content
The Chat Archive
o1-preview-2024-09-12· OpenAI WildChat-4.8M (AI2)

/* * File: main.c * Example of using a 16-bit tuning word for a simple DDS (Direct…

  1. User

    /*

    • File: main.c
    • Example of using a 16-bit tuning word for a simple DDS (Direct Digital Synthesis)
    • on a PIC16F1503 with minimal float usage to reduce memory overhead.
    • The code demonstrates:
      1. 16-bit phase accumulator (phAcc).
      1. 16-bit tuning word calculation using purely integer math.
      1. A 256-sample sine lookup table.
      1. 3-phase output using 3 PWM channels if available (PWM1, PWM2, PWM3).
    • NOTE:
      • Adjust oscillator settings, #pragma config, and #defines for your hardware.
      • This example uses minimal float usage only for an optional setFrequency16Bit()
    • function. If needed, you can remove or replace it with completely integer-based math. */

    /----------------------------------------------------------------------------/ /* PIC16F1503 Configuration Bit Settings / /----------------------------------------------------------------------------*/ // CONFIG1 #pragma config FOSC = INTOSC // Oscillator: INTOSC #pragma config WDTE = OFF // Watchdog Timer Enable: off #pragma config PWRTE = OFF // Power-up Timer Enable: off #pragma config MCLRE = OFF // MCLR Pin Function: MCLR off (digital input) #pragma config CP = OFF // Flash Program Memory Code Protection: off #pragma config BOREN = OFF // Brown-out Reset Enable: off #pragma config CLKOUTEN = OFF // Clock Out Enable: off

    // CONFIG2 #pragma config WRT = OFF // Flash Memory Self-Write Protection: off #pragma config STVREN = OFF // Stack Overflow/Underflow Reset Enable: off #pragma config BORV = LO // Brown-out Reset Voltage: low trip point #pragma config LPBOR = OFF // Low-Power Brown Out Reset: off #pragma config LVP = OFF // Low-Voltage Programming Enable: off

    #include <xc.h> #include <stdint.h>

    /----------------------------------------------------------------------------/ /* Defines / /----------------------------------------------------------------------------*/ #define _XTAL_FREQ 16000000UL // 16 MHz internal oscillator #define SAMPLE_RATE 17085UL // Approx. PWM or interrupt frequency

    /----------------------------------------------------------------------------/ /* DDS Global Variables / /----------------------------------------------------------------------------*/

    static volatile uint16_t phAcc = 0;

    static volatile uint16_t tuningWord = 0;

    static volatile uint8_t amplitude = 255;

    static const uint8_t sine_LUT[256] = { 0x7f, 0x82, 0x84, 0x87, 0x89, 0x8c, 0x8e, 0x91, 0x93, 0x96, 0x98, 0x9b, 0x9d, 0xa0, 0xa2, 0xa5, 0xa7, 0xaa, 0xac, 0xae, 0xb1, 0xb3, 0xb5, 0xb8, 0xba, 0xbc, 0xbf, 0xc1, 0xc3, 0xc5, 0xc7, 0xc9, 0xcb, 0xcd, 0xcf, 0xd1, 0xd3, 0xd5, 0xd7, 0xd9, 0xdb, 0xdc, 0xde, 0xe0, 0xe1, 0xe3, 0xe5, 0xe6, 0xe8, 0xe9, 0xea, 0xec, 0xed, 0xee, 0xef, 0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7, 0xf7, 0xf8, 0xf9, 0xfa, 0xfa, 0xfb, 0xfb, 0xfc, 0xfc, 0xfd, 0xfd, 0xfd, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfd, 0xfd, 0xfd, 0xfc, 0xfc, 0xfb, 0xfb, 0xfa, 0xfa, 0xf9, 0xf8, 0xf7, 0xf7, 0xf6, 0xf5, 0xf4, 0xf3, 0xf2, 0xf1, 0xef, 0xee, 0xed, 0xec, 0xea, 0xe9, 0xe8, 0xe6, 0xe5, 0xe3, 0xe1, 0xe0, 0xde, 0xdc, 0xdb, 0xd9, 0xd7, 0xd5, 0xd3, 0xd1, 0xcf, 0xcd, 0xcb, 0xc9, 0xc7, 0xc5, 0xc3, 0xc1, 0xbf, 0xbc, 0xba, 0xb8, 0xb5, 0xb3, 0xb1, 0xae, 0xac, 0xaa, 0xa7, 0xa5, 0xa2, 0xa0, 0x9d, 0x9b, 0x98, 0x96, 0x93, 0x91, 0x8e, 0x8c, 0x89, 0x87, 0x84, 0x82, 0x7f, 0x7c, 0x7a, 0x77, 0x75, 0x72, 0x70, 0x6d, 0x6b, 0x68, 0x66, 0x63, 0x61, 0x5e, 0x5c, 0x59, 0x57, 0x54, 0x52, 0x50, 0x4d, 0x4b, 0x49, 0x46, 0x44, 0x42, 0x3f, 0x3d, 0x3b, 0x39, 0x37, 0x35, 0x33, 0x31, 0x2f, 0x2d, 0x2b, 0x29, 0x27, 0x25, 0x23, 0x22, 0x20, 0x1e, 0x1d, 0x1b, 0x19, 0x18, 0x16, 0x15, 0x14, 0x12, 0x11, 0x10, 0x0f, 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08, 0x07, 0x07, 0x06, 0x05, 0x04, 0x04, 0x03, 0x03, 0x02, 0x02, 0x01, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x01, 0x02, 0x02, 0x03, 0x03, 0x04, 0x04, 0x05, 0x06, 0x07, 0x07, 0x08, 0x09, 0x0a, 0x0b, };

    void init_osc(void); void setFrequency16Bit(uint16_t freq); void init_pwm(void);

    void ADC_Init(void); uint16_t ADC_Read(uint8_t channel);

    void main(void)

    { // Initialize the internal oscillator init_osc();

    // Initialize PWM
    init_pwm();
    
    // Example: Set initial frequency to 180 Hz
    setFrequency16Bit(160);
    
    ADC_Init();
    
    // Enable global interrupts
    INTCONbits.PEIE = 1;  // Peripheral Interrupt Enable
    INTCONbits.GIE  = 1;  // Global Interrupt Enable
    
    uint16_t lastFreq = 0;  // Track last frequency to avoid unnecessary updates
    // Main loop
    while (1)
    {
       uint16_t adcValue = ADC_Read(0);
        
        // Improved mapping with better precision
        uint16_t freq = 25 + ((uint32_t)adcValue * 135) / 1023;  // 25 to 160 Hz range
        
        // Only update if frequency changed significantly (reduce jitter)
        if (abs(freq - lastFreq) > 2) {
            setFrequency16Bit(freq);
            lastFreq = freq;
        }
        
        __delay_ms(20);  // Shorter delay for better responsiveness
    }
    

    }

    void init_osc(void)

    { // Set internal oscillator to 16 MHz OSCCONbits.IRCF = 0b1111; // 16 MHz OSCCONbits.SCS = 0b10; // Internal oscillator }

    void setFrequency16Bit(uint16_t freqHz) { // Improved tuning word calculation uint32_t temp = (uint32_t)freqHz * 65536UL; tuningWord = (uint16_t)(temp / SAMPLE_RATE); }

    void init_pwm(void)

    { // Configure Timer2 for PWM // Prescaler = 1, PR2 adjusts PWM frequency T2CONbits.T2CKPS = 0b00; // Prescaler = 1 PR2 = 220; // ~20 kHz if FOSC=16 MHz (approx) T2CONbits.TMR2ON = 1; // Enable Timer2

    // Configure PWM modules (depending on your PIC)
    PWM1CON = 0xC0;  // Enable PWM1, active-high
    PWM2CON = 0xC0;  // Enable PWM2, active-high
    PWM3CON = 0xC0;  // Enable PWM3, active-high
    
    // Make sure PWM pins are outputs
    TRISCbits.TRISC5 = 0;  // PWM1 output
    TRISCbits.TRISC3 = 0;  // PWM2 output
    TRISAbits.TRISA2 = 0;  // PWM3 output
    
    // Enable Timer2 interrupt for the DDS update
    PIR1bits.TMR2IF = 0;
    PIE1bits.TMR2IE = 1;
    

    }

    void ADC_Init(void) { // ANSELx: Enable analog function on RA0 ANSELAbits.ANSA0 = 1; TRISAbits.TRISA0 = 1; // RA0 as input

    // Modify ADC clock setting for better stability
    ADCON1bits.ADFM = 1;     // Right justified
    ADCON1bits.ADCS = 0b110; // Change to Fosc/64 for more stable readings
    ADCON1bits.ADPREF = 0b00;// Vref = Vdd
    
    ADCON0bits.CHS = 0b0000; // Select AN0 channel
    ADCON0bits.ADON = 1;     // Enable ADC
    __delay_ms(5);           // Longer stabilization delay
    

    }

    uint16_t ADC_Read(uint8_t channel) { // Select the ADC channel (assuming AN0 is at channel=0, check datasheet for correct AN channel) ADCON0 &= 0xC3; // Clear channel selection bits ADCON0 |= (channel << 2); __delay_us(20); // Acquisition time

    GO_nDONE = 1;           // Start A/D conversion
    while(GO_nDONE);        // Wait for conversion complete
    
    // Combine the 10-bit result
    uint16_t result = ((uint16_t)ADRESH << 8) | ADRESL;
    return result;
    

    }

    void __interrupt() isr(void)

    { // Timer2 interrupt if (PIE1bits.TMR2IE && PIR1bits.TMR2IF) { PIR1bits.TMR2IF = 0;

        // Increment phase accumulator by tuningWord
        phAcc += tuningWord;
        
        // Top 8 bits of phase accumulator => LUT index
        // phAcc is 16 bits, so (phAcc >> 8) = top 8 bits
        uint8_t indexA = (uint8_t)(phAcc >> 8);
        
        // For 3-phase, add an offset for indexB (120°) and indexC (240°).
        // 256/3 = 85.3 ~ 85 for 120°, 170 for 240°.
        uint8_t indexB = (uint8_t)(indexA + 85);
        uint8_t indexC = (uint8_t)(indexA + 170);
        
        // Retrieve samples from the LUT
        uint8_t sampA = sine_LUT[indexA];
        uint8_t sampB = sine_LUT[indexB];
        uint8_t sampC = sine_LUT[indexC];
        
        // Scale by amplitude (0..255)
        sampA = (uint8_t)(((uint16_t)sampA * amplitude) >> 8);
        sampB = (uint8_t)(((uint16_t)sampB * amplitude) >> 8);
        sampC = (uint8_t)(((uint16_t)sampC * amplitude) >> 8);
        
        // Update PWM duty cycles (8-bit duty high register for each PWM)
        PWM1DCH = sampA;
        PWM2DCH = sampB;
        PWM3DCH = sampC;
    }
    

    }

  2. Assistant

    Hello!

    It looks like you've shared code for implementing a simple Direct Digital Synthesis (DDS) on a PIC16F1503 microcontroller. The code initializes the oscillator, sets up PWM outputs, reads analog input via the ADC to adjust the output frequency, and generates a 3-phase sine wave using a sine lookup table.

    How can I assist you with this code?

    • Do you need help understanding certain parts of the implementation?
    • Are you encountering any issues or bugs that you'd like assistance with?
    • Would you like suggestions for optimizing or improving the code?

    Please provide more details about how I can help, and I'll be happy to assist you further!