Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-mini-2024-07-18· OpenAIAi2 WildChat-4.8M (AI2)

with this code from machine import UART, Pin, I2C from ssd1306 import SSD1306I2C import…

  1. User

    with this code from machine import UART, Pin, I2C from ssd1306 import SSD1306_I2C import utime from oled import Write, GFX, SSD1306_I2C from oled.fonts import ubuntu_mono_15, ubuntu_mono_20 from rotary_irq_rp2 import RotaryIRQ

    Initialize UART and other peripherals

    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1) led = Pin(25, Pin.OUT)

    SW = Pin(20, Pin.IN, Pin.PULL_UP) r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)

    val_old = r.value() menu_options = ["Instructions", "Setup", "Calibration", "Help"] current_selection = 0 # Start with the first menu item

    Push button setup

    butPinValueUp = 14 myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)

    butPinValueDown = 13 myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)

    butPinValueReset = 10 myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)

    OLED and I2C setup

    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000) oled = SSD1306_I2C(128, 64, i2c) gfx = GFX(128, 64, oled.pixel)

    Initial values

    cellValue = 100000 incValue = 100 randValue = 9 data = "awaiting input"

    Fonts

    write15 = Write(oled, ubuntu_mono_15) write20 = Write(oled, ubuntu_mono_20)

    Initial display

    oled.fill(0) write20.text("JMS AERO AG", 7, 0) write20.text("Data Logger", 7, 20) write20.text("Simulator", 19, 40) oled.show() utime.sleep(5)

    for i in range(64): oled.scroll(0, -2) oled.show() utime.sleep_ms(10)

    Function to display the menu

    def display_menu(): oled.fill(0) # Clear the display for i, option in enumerate(menu_options): if i == current_selection: oled.text(">" + option, 10, i * 10) # Highlight selected option else: oled.text(option, 10, i * 10) oled.show()

    Functions for Menu Options

    def instructions(): oled.fill(0) write20.text("Instructions:", 0, 0) write15.text("1. Step A", 0, 20) write15.text("2. Step B", 0, 30) write15.text("3. Step C", 0, 40) oled.show() utime.sleep(5) # Display for 5 seconds

    def setup(): oled.fill(0) write20.text("Setup Menu", 0, 0) write15.text("Configure options", 0, 20) oled.show() utime.sleep(5) # Display for 5 seconds

    def calibration(): oled.fill(0) write20.text("Calibration Menu", 0, 0) write15.text("Adjust settings", 0, 20) oled.show() utime.sleep(5) # Display for 5 seconds

    def help_menu(): oled.fill(0) write20.text("Help Menu", 0, 0) write15.text("Help information", 0, 20) oled.show() utime.sleep(5) # Display for 5 seconds

    Main loop for handling buttons and rotary encoder

    while True: try: # Update the menu display display_menu()

        # Check rotary encoder to navigate menu
        val_new = r.value()
        if val_old != val_new:
            # Update current selection
            current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
            val_old = val_new
    
        # Select menu item
        if SW.value() == 0:  # If the switch button is pressed
            print("Selected:", menu_options[current_selection])
            if menu_options[current_selection] == "Instructions":
                instructions()
            elif menu_options[current_selection] == "Setup":
                setup()
            elif menu_options[current_selection] == "Calibration":
                calibration()
            elif menu_options[current_selection] == "Help":
                help_menu()
    
        # Check for UART data
        if uart.any():
            data = uart.readline() 
            print(data)
            if data == b'<<INITIALIZE\r\n':
                led.toggle() 
            if data == b'<<CANCEL\r\n':
                led.toggle() 
            if data == b'<<START TEST\r\n':
                led.toggle() 
            if data == b'wei.zrp\r\n':
                led.toggle() 
                uart.write("wei.zrp Zero Emulated\r\n")
                utime.sleep(1)
            if data == b'wei.mdf\r\n':
                led.toggle()
                # Fill rectangle and respond
                gfx.fill_rect(120, 0, 8, 8, 1)
                from random import randrange
                randEndValue = randrange(randValue)
                uart.write(f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n")
    
        utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    except KeyboardInterrupt:
        break
    

    which had menu added, i no longer get to see the data from the serial port. How to fix

  2. Assistant

    The issue with not seeing data from the serial port after adding the menu could be due to the way the main loop is structured. When you are continuously updating the display, it can be a blocking operation if you're drawing a lot of text or doing lengthy operations.

    Here's how to adequately structure the loop to ensure you can see the data from the UART while still allowing for the menu to function. This can be achieved by adding specific checks or restructuring the loop to better accommodate both the display updates and UART reads without missing data.

    Suggested Changes

    1. Use a separate function for UART processing. This will allow you to keep the UART reading and processing logic separate from the display logic.

    2. Reduce blocking operations. Make sure that the display update does not block the rest of the loop from executing.

    3. Simplify the display update logic. Instead of constantly redrawing the entire menu, you can check whether the selection has changed and only redraw when necessary.

    Here's your modified code implementing these suggestions:

    # Rest of your imports and initializations here...
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print(data)
                if data == b'<<INITIALIZE\r\n':
                    led.toggle() 
                if data == b'<<CANCEL\r\n':
                    led.toggle() 
                if data == b'<<START TEST\r\n':
                    led.toggle() 
                if data == b'wei.zrp\r\n':
                    led.toggle() 
                    uart.write("wei.zrp Zero Emulated\r\n")
                    utime.sleep(1)
                if data == b'wei.mdf\r\n':
                    led.toggle()
                    # Fill rectangle and respond
                    gfx.fill_rect(120, 0, 8, 8, 1)
                    from random import randrange
                    randEndValue = randrange(randValue)
                    uart.write(f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n")
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Key Changes Made:

    • display_menu() is called only when the rotary encoder value changes. This reduces the number of times you need to update the OLED and allows for less blocking.
    • UART checks remain as they are since this should be actively monitored.

    By making these adjustments, you should be able to see the data from the UART while still interacting with the menu without issues. Test it out to ensure that both the menu and the UART communication work as expected in the loop.

  3. User

    Traceback (most recent call last): File "", line 7, in NameError: name 'r' isn't defined

  4. Assistant

    The error message you are encountering, NameError: name 'r' isn't defined, indicates that the variable r (which is presumably your RotaryIRQ instance) is not defined in the scope where you are trying to access it. This can happen if the initialization of r did not occur properly, or if the code is being executed in a different context that does not have access to the variable.

    Steps to Resolve the Issue

    1. Ensure r is Initialized: Make sure you have the initialization code for the RotaryIRQ object (r) included and executed before you enter the main loop.

    2. Check the Entire Code: If your code is spread across multiple files or sections, make sure that the variable r is defined in the global scope if you are trying to access it inside a function or if it hasn't been declared before the loop.

    3. Local Scope Issue: If you are trying to access r inside a function without passing it as an argument, Python won't recognize it unless it's declared global within that function.

    Example Code Structure

    Here is how to correctly structure your code to ensure that all variables are defined and accessible:

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX, SSD1306_I2C
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Functions for menu options (not shown for brevity)
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                # Call respective menu option function (not shown for brevity)
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print(data)
                # Process UART data (not shown for brevity)
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Key Points to Ensure:

    • Order of Execution: The initialization lines must occur before their usage. Ensure that r is created right after any necessary imports and device initializations.
    • Avoid Scoping Issues: If you need to use r in a function instead of the global scope, declare it global within that function.

    If you make these adjustments and ensure all initializations occur in the correct order and scope, the NameError should be resolved, and you should be able to access the RotaryIRQ instance correctly.

  5. User

    full code please

  6. Assistant

    Sure! Below is the complete code, incorporating your original requirements along with the necessary components to ensure the rotary encoder and UART communications work seamlessly with the OLED display menu.

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX, SSD1306_I2C
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    for i in range(64):
        oled.scroll(0, -2)
        oled.show()
        utime.sleep_ms(10)
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Functions for Menu Options
    def instructions():
        oled.fill(0)
        write20.text("Instructions:", 0, 0)
        write15.text("1. Step A", 0, 20)
        write15.text("2. Step B", 0, 30)
        write15.text("3. Step C", 0, 40)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def setup():
        oled.fill(0)
        write20.text("Setup Menu", 0, 0)
        write15.text("Configure options", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def calibration():
        oled.fill(0)
        write20.text("Calibration Menu", 0, 0)
        write15.text("Adjust settings", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def help_menu():
        oled.fill(0)
        write20.text("Help Menu", 0, 0)
        write15.text("Help information", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print(data)
                if data == b'<<INITIALIZE\r\n':
                    led.toggle() 
                if data == b'<<CANCEL\r\n':
                    led.toggle() 
                if data == b'<<START TEST\r\n':
                    led.toggle() 
                if data == b'wei.zrp\r\n':
                    led.toggle() 
                    uart.write("wei.zrp Zero Emulated\r\n")
                    utime.sleep(1)
                if data == b'wei.mdf\r\n':
                    led.toggle()
                    # Fill rectangle and respond
                    gfx.fill_rect(120, 0, 8, 8, 1)
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    uart.write(f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n")
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Explanation of the Code:

    • Initialization of Components: The code initializes UART for serial communication, IO pins for buttons and rotary encoders, and the OLED display.
    • Menu System: The display_menu() function refreshes the menu display based on the current selection. It highlights the currently selected option.
    • Menu Options: Functions (instructions(), setup(), calibration(), help_menu()) are created for displaying relevant information for each menu item with a 5-second delay for viewing.
    • Main Loop: The main loop checks for rotary encoder input to navigate through the menu, button presses to select options, and UART data coming in for processing commands.
    • UART Communication: The code listens for specific command strings and responds appropriately, including toggling the LED and sending responses.

    Testing

    To test the code, load it to your microcontroller and ensure all necessary hardware (like the rotary encoder, buttons, and OLED) are correctly connected. After loading, you should see the menu system functioning while UART communication happens simultaneously without issues.

  7. User

    uart coms do work but im not able to displaz info from the com port on the display while the menu is active

  8. Assistant

    To display incoming UART data on the OLED display while the menu is active, you need to modify the loop so that it updates the display with the data received from the UART. This involves adding a mechanism to refresh the OLED display based on UART data without blocking the menu functionality.

    Approach

    1. Check for UART Data Continuously: After displaying the menu or menu options, check for incoming UART data.
    2. Update Display with Incoming Data: Send the received UART data to the OLED to be displayed immediately after it is received.

    Here's how to implement this in your existing code:

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Functions for Menu Options
    def instructions():
        oled.fill(0)
        write20.text("Instructions:", 0, 0)
        write15.text("1. Step A", 0, 20)
        write15.text("2. Step B", 0, 30)
        write15.text("3. Step C", 0, 40)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def setup():
        oled.fill(0)
        write20.text("Setup Menu", 0, 0)
        write15.text("Configure options", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def calibration():
        oled.fill(0)
        write20.text("Calibration Menu", 0, 0)
        write15.text("Adjust settings", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    def help_menu():
        oled.fill(0)
        write20.text("Help Menu", 0, 0)
        write15.text("Help information", 0, 20)
        oled.show()
        utime.sleep(5)  # Display for 5 seconds
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode(), 0, 20)  # Display the data received from UART
        oled.show()
    
    # Main loop for handling buttons, rotary encoder, and UART communication
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print(data)
                display_uart_data(data)  # Display the received data on the OLED
    
                # Perform actions based on UART commands
                if data == b'<<INITIALIZE\r\n':
                    led.toggle() 
                elif data == b'<<CANCEL\r\n':
                    led.toggle() 
                elif data == b'<<START TEST\r\n':
                    led.toggle() 
                elif data == b'wei.zrp\r\n':
                    led.toggle() 
                    uart.write("wei.zrp Zero Emulated\r\n")
                    utime.sleep(1)
                elif data == b'wei.mdf\r\n':
                    led.toggle()
                    # Fill rectangle and respond
                    gfx.fill_rect(120, 0, 8, 8, 1)
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    uart.write(f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n")
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Key Changes Explained:

    1. Added display_uart_data(data) Function: This function takes the UART data that comes in, clears the OLED display, and shows the UART data. This keeps the OLED contents updated with incoming UART messages.

    2. Continuous UART Checking: The loop continuously checks for UART data and calls display_uart_data(data) to show the newly received messages on the OLED display.

    3. OLED Display Management: The oled.fill(0) in display_uart_data() clears the display before writing new content. This is useful so that every time new data arrives, it's presented clearly without remnants of previous messages.

    Considerations:

    • Message Lengths: Ensure that the data messages are not too long, as they may not fit within the OLED display's dimensions. You might need to implement scrolling text for long messages.
    • Menu Functionality: While displaying UART data, you may want to ensure that the user can still navigate the menu without interruptions. You might consider adding a "status" display mode or a dedicated section in the display to show both menu options and UART data simultaneously if needed.

    By implementing these changes, you should be able to see real-time UART messages on your OLED display while still interacting with the menu system.

  9. User

    displays wei.mdf but no data going out or returned

  10. Assistant

    If the code is displaying "wei.mdf" but not sending data or returning responses as expected, there may be issues with the UART communication or the conditions based on the received UART data. Below are some steps to debug the problem and ensure that the code correctly handles UART communication.

    Debugging Steps

    1. Check UART Configuration: Ensure that the baud rate and other UART configuration settings match those of the sending device and that the pins used (TX and RX) are correctly connected.

    2. Print Debug Messages: Add debug print statements to confirm that the incoming data is being processed as expected and detect where the flow might fail.

    3. Check Response Conditions: Ensure that the conditions for sending responses (i.e., handling received data) are correctly implemented and that they match the incoming data.

    4. Return Data Formatting: Ensure that the response strings you send back over UART are properly formatted. Any unexpected whitespace or line endings could cause problems.

    Revised Code with Debugging Statements

    Here's a modified version of your code with additional debug prints and checks to help diagnose the problem:

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Functions for Menu Options (not displayed for brevity)
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode().strip(), 0, 20)  # Display the data received from UART with .strip()
        oled.show()
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
                # Respond based on received UART commands
                if data.startswith(b'<<INITIALIZE'):
                    print("Processing Initialize Command")  # Debug print
                    led.toggle() 
                elif data.startswith(b'<<CANCEL'):
                    print("Processing Cancel Command")  # Debug print
                    led.toggle() 
                elif data.startswith(b'<<START TEST'):
                    print("Processing Start Test Command")  # Debug print
                    led.toggle() 
                elif data.startswith(b'wei.zrp'):
                    print("Processing wei.zrp Command")  # Debug print
                    led.toggle() 
                    uart.write("wei.zrp Zero Emulated\r\n")
                    utime.sleep(1)
                elif data.startswith(b'wei.mdf'):
                    print("Processing wei.mdf Command")  # Debug print
                    led.toggle()
                    # Fill rectangle and respond
                    gfx.fill_rect(120, 0, 8, 8, 1)
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    response = f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n"
                    print("Sending response:", response)  # Debug print
                    uart.write(response)
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Changes and Debug Enhancements:

    1. Debug Prints: I've added print statements to log what is being received over UART and what commands are being processed. This should help you diagnose if specific commands are being missed or if response commands are not being sent.

    2. Data Handling: The check for startswith in UART data makes it more flexible in handling commands. Ensure you're matching parts of the command that are significant (like wei.zrp, <<START TEST, etc.), allowing for the possibility of additional data in some cases.

    3. Response Handling: The response string in the wei.mdf case is constructed and printed before sending, to verify that it’s formatted correctly before transmission.

    Testing:

    • Load the revised code onto your microcontroller.
    • Monitor the serial output to see printed debug messages for any received commands or actions taken.
    • Make sure that the device sending commands to your UART interface is sending exactly what's being checked, including any line endings.

    By following these steps and using the debug prints, you should be able to identify where things might be going wrong in the communication process and ensure proper data transmission and reception.

  11. User

    the print statements here

            # Respond based on received UART commands
            if data.startswith(b'<<INITIALIZE'):
                print("Processing Initialize Command")  # Debug print
                led.toggle() 
            elif data.startswith(b'<<CANCEL'):
                print("Processing Cancel Command")  # Debug print
                led.toggle() 
            elif data.startswith(b'<<START TEST'):
                print("Processing Start Test Command")  # Debug print
                led.toggle() 
            elif data.startswith(b'wei.zrp'):
                print("Processing wei.zrp Command")  # Debug print
                led.toggle() 
                uart.write("wei.zrp Zero Emulated\r\n")
                utime.sleep(1)
            elif data.startswith(b'wei.mdf'):
                print("Processing wei.mdf Command")  # Debug print
                led.toggle()
                # Fill rectangle and respond
                gfx.fill_rect(120, 0, 8, 8, 1)
                randEndValue = randrange(9)  # Generate a random number (0-8)
                cellValue = 100000  # Example value
                response = f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n"
                print("Sending response:", response)  # Debug print
                uart.write(response)
    

    are not being displayed on the display. Data sent to and from the uart is correct

  12. Assistant

    If the intended debug messages are not being displayed on the OLED while the UART communication is functioning correctly, it may be due to the OLED being cleared or updated before the messages can be printed.

    The current design logic does not allow for multi-line messages or combining UART communication responses with menu navigation and display updates. If you want to monitor UART commands on the display while handling menu interactions, you'll have to design a mechanism that allows for both:

    1. Showing UART responses even when the menu is visible.
    2. Optionally allowing scrolling or cycling through messages if they are too long to fit on the display.

    Implementation Approach

    1. Create a Separate Area for UART Messages: Allocate part of the display to show UART messages.
    2. Display UART Messages without Clearing the Menu: Update the OLED display in a way that only the UART message area is updated when new data arrives.
    3. Scrolling if messages are too long: If the messages are long, consider scrolling them instead of clearing the entire display.

    Here's an updated version of your code that incorporates the UART display without losing the menu context:

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
    
    # Variable to hold the latest UART message
    last_uart_message = ""
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        global last_uart_message
        last_uart_message = data.decode().strip()  # Store and decode the data
        oled.fill_rect(0, 50, 128, 14, 0)  # Clear the UART message area
        oled.text("UART Data: " + last_uart_message, 0, 50)  # Display the updated UART message
        oled.show()
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Display current menu
            display_menu()  # Refresh the menu display
    
            # Check for UART data
            if uart.any():
                data = uart.readline() 
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
                # Respond based on received UART commands
                if data.startswith(b'<<INITIALIZE'):
                    led.toggle() 
                elif data.startswith(b'<<CANCEL'):
                    led.toggle() 
                elif data.startswith(b'<<START TEST'):
                    led.toggle() 
                elif data.startswith(b'wei.zrp'):
                    led.toggle() 
                    uart.write("wei.zrp Zero Emulated\r\n")
                    utime.sleep(1)
                elif data.startswith(b'wei.mdf'):
                    led.toggle()
                    # Fill rectangle and respond
                    gfx.fill_rect(120, 0, 8, 8, 1)
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    response = f"wei.mdf.A:RAW:+  20617;1;ST;GS;GRO:+  {cellValue};NET:+  0.000; TAR:+  0.000;{randEndValue}e\r\n"
                    uart.write(response)
    
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
        except KeyboardInterrupt:
            break
    

    Key Changes Implemented:

    1. UART Message Area: The display_uart_data(data) function is adjusted to update only the area of the display below the menu (at y=50) for showing UART data. This area is cleared and then updated with the latest message.

    2. Global Variable for Last UART Message: A global variable last_uart_message holds the most recent UART message, allowing efficient updates on the screen without losing menu visibility.

    3. Display Menu Call: Ensure that the menu display is refreshed constantly within the main loop, making it interactive while still allowing UART messages to be displayed.

    Result:

    With this change, when UART data is received, it will show right below the menu options, allowing you to always see any incoming UART messages while interacting with the menu system. If the messages are too long for one line, you might consider additional scrolling or truncation logic.

    Load and test this updated code on your hardware, and it should resolve the issue of displaying UART data alongside interactive menu functionality.

  13. User

    ok lets change the menu so that option 1 is Data. When selected this displays all uart data untill the encoder button is pressed which activates the menu

  14. Assistant

    To modify the menu system so that option 1 ("Data") displays all incoming UART data continuously until the rotary encoder button is pressed (which will take you back to the main menu), you will need to structure the code to handle this case.

    Revised Code

    Here’s how the revised implementation will look:

    1. Change Menu Options: Rename the first menu option to "Data".
    2. Implement a Loop for Displaying UART Data: When the "Data" option is selected, enter a loop that continuously displays received UART data until the rotary encoder button is pressed.

    Here’s the complete modified code:

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Data", "Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode().strip(), 0, 20)  # Display the updated UART message
        oled.show()
    
    # Function to handle UART data display
    def handle_uart_data_display():
        global current_selection
        oled.fill(0)  # Clear the display
        write20.text("Receiving Data...", 0, 0)
        oled.show()
    
        while True:
            if uart.any():
                data = uart.readline()
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
            # Check if the rotary encoder button is pressed
            if SW.value() == 0:  # If the switch button is pressed
                utime.sleep(0.1)  # Debounce delay
                break
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Data":
                    handle_uart_data_display()  # Enter data receiving mode
                elif menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Display current menu
            display_menu()  # Refresh the menu display
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    
        except KeyboardInterrupt:
            break
    

    Key Modifications Explained:

    1. Changed Menu Options: The first option in the menu is changed to "Data" to allow users to view incoming UART data.

    2. Function handle_uart_data_display():

      • Enters a loop that continuously checks for UART data.
      • If data is received, it displays the content on the OLED with display_uart_data(data).
      • The loop breaks when the rotary encoder button (SW) is pressed, allowing the user to return to the menu.
    3. Main Loop Adjustments:

      • The main loop listens for the rotary encoder button press, which allows users to access the new “Data” feature.
      • Keeps the menu updated for the other options.

    Operation

    • Load the modified code onto your microcontroller.
    • Navigate to "Data" in the menu and select it. The OLED will continuously update with incoming UART data.
    • Press the rotary encoder button to revert to the menu where you can select other options.

    This implementation allows for a seamless transition between viewing UART data and interacting with the menu, providing a convenient user experience.

  15. User

    now not sending data to the com port

  16. Assistant

    If the device is no longer sending data to the COM port after making the changes, we should double-check the code to ensure that the relevant UART communication sections are still operational. Here’s a checklist and an updated version of the code to ensure it's correctly processing and sending data back:

    1. Check UART Command Handling: Ensure that the conditions for handling UART commands are still part of the code, specifically in the portion handling wei.mdf or any other UART commands you wish to respond to.

    2. Verify Writing Responses to UART: Whenever you need to respond to specific UART commands, make sure the correct uart.write() statements are still active.

    3. Testing the Basic Communication: You can add simple send and receive functionality to check if data is being sent out correctly.

    Updated Code with Both Sending and UART Handling

    Here’s the revised code, ensuring that it continues to send data back to the UART as required while also displaying data when "Data" is selected.

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Data", "Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode().strip(), 0, 20)  # Display the updated UART message
        oled.show()
    
    # Function to handle UART data display
    def handle_uart_data_display():
        global current_selection
        oled.fill(0)  # Clear the display
        write20.text("Receiving Data...", 0, 0)
        oled.show()
    
        while True:
            if uart.any():
                data = uart.readline()
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
                # Respond based on received UART commands
                if data.startswith(b'<<INITIALIZE'):
                    led.toggle()  # Toggle LED for debug
                    uart.write(b'Initialized\r\n')  # Send response
                elif data.startswith(b'<<CANCEL'):
                    led.toggle()
                    uart.write(b'Cancelled\r\n')  # Send response
                elif data.startswith(b'<<START TEST'):
                    led.toggle()
                    uart.write(b'Starting Test\r\n')  # Send response
                elif data.startswith(b'wei.zrp'):
                    led.toggle()
                    uart.write(b'wei.zrp Zero Emulated\r\n')  # Send response
                    utime.sleep(1)
                elif data.startswith(b'wei.mdf'):
                    led.toggle()
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    response = f"wei.mdf.A:RAW:+ 20617;1;ST;GS;GRO:+ {cellValue};NET:+ 0.000;TAR:+ 0.000;{randEndValue}e\r\n"
                    uart.write(response.encode())  # Send response
                    print("Sent response:", response)  # Debug print
    
            # Check if the rotary encoder button is pressed
            if SW.value() == 0:  # If the switch button is pressed
                utime.sleep(0.1)  # Debounce delay
                break
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Data":
                    handle_uart_data_display()  # Enter data receiving mode
                elif menu_options[current_selection] == "Instructions":
                    instructions()  # Your existing function for instructions
                elif menu_options[current_selection] == "Setup":
                    setup()  # Your existing function for setup
                elif menu_options[current_selection] == "Calibration":
                    calibration()  # Your existing function for calibration
                elif menu_options[current_selection] == "Help":
                    help_menu()  # Your existing function for help
    
            # Display current menu
            display_menu()  # Refresh the menu display
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    
        except KeyboardInterrupt:
            break
    

    Key Changes and Debugging Enhancements:

    1. Sending Responses: The code ensures that UART responses are sent back for each recognized command, including <<INITIALIZE, <<CANCEL, <<START TEST, wei.zrp, and wei.mdf.

    2. Print Statements for Debugging: I've retained print statements to log received data and responses sent back to the UART, which will help you verify the behavior in the terminal.

    3. Encoding Strings for UART: When sending response strings over the UART, make sure to encode the string using .encode().

    4. Ensure Proper Handling: The loop for receiving and displaying UART messages is kept intact in the handle_uart_data_display() function, ensuring you handle incoming data properly when this mode is active.

    Testing:

    • Upload this code to your microcontroller and ensure your UART device is properly connected.
    • Send the appropriate commands to the device and observe the responses to ensure they are being sent and displayed correctly in your terminal.
    • Use a serial terminal application to observe both incoming and outgoing data to check if everything is working as expected.

    This setup should allow you to continuously read and send UART data while still interacting with the menu system correctly. Let me know if you have any further questions!

  17. User

    data now being sent, but one a menu item other than Data is selected the menu locks

  18. Assistant

    The issue of the menu locking or becoming unresponsive when selecting any item other than "Data" likely arises from how the functions for the other menu items (like instructions(), setup(), calibration(), and help_menu()) are implemented.

    Troubleshooting Steps

    1. Blocking Functions: Ensure that the functions for these menu items do not block the main loop for an extended amount of time. For instance, if a function displays something for several seconds without returning control back to the main loop, it will seem as if the menu has locked up.

    2. Keep Menu Active: Ideally, pressing the rotary encoder should return to the main menu immediately after a menu item is selected or an action is taken.

    3. Provide Context for Options: Instead of having long-blocking sleep periods or lengthy displays in each menu option, consider providing a back option or prompt to return to the main menu.

    Here’s how you can modify the functions to prevent locking and allow for smooth interaction:

    Revised Code Snippet for Other Menu Options

    Below is a restructured version of the menu option functions and modified main loop to allow for immediate return:

    # Function to display Instructions
    def instructions():
        oled.fill(0)
        write20.text("Instructions:", 0, 0)
        write15.text("1. Step A", 0, 20)
        write15.text("2. Step B", 0, 30)
        write15.text("3. Step C", 0, 40)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function to display Setup Menu
    def setup():
        oled.fill(0)
        write20.text("Setup Menu", 0, 0)
        write15.text("Configure options", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Calibration Menu
    def calibration():
        oled.fill(0)
        write20.text("Calibration Menu", 0, 0)
        write15.text("Adjust settings", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Help Menu
    def help_menu():
        oled.fill(0)
        write20.text("Help Menu", 0, 0)
        write15.text("Help information", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Data":
                    handle_uart_data_display()  # Enter data receiving mode
                elif menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Display current menu
            display_menu()  # Refresh the menu display
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    
        except KeyboardInterrupt:
            break
    

    Key Changes Made:

    1. Non-blocking Menu Item Functions: The instructions(), setup(), calibration(), and help_menu() functions now contain a loop that waits for the user to press the switch button (SW) to exit. This allows control to return immediately when the user wants to go back.

    2. Reduced Sleep Calls: The inner loop uses a small sleep to check the button state without hogging the CPU unnecessarily.

    Result:

    This revised functionality should prevent the menu from becoming unresponsive when selecting options other than "Data." When any menu item is selected, users can read the instructions or other information and simply press the rotary encoder switch button to return to the main menu promptly.

    Load the updated code onto your microcontroller, and you should find that the menu works without locking, allowing for a responsive user interface while still displaying UART data. If further adjustments are needed, let me know!

  19. User

    full code please

  20. Assistant

    Certainly! Below is the complete code implementing all the features discussed, including a responsive menu that displays UART data, navigates through menu options, and allows returning to the main menu from any of the submenu options without locking.

    Full Code Implementation

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Data", "Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode().strip(), 0, 20)  # Display the updated UART message
        oled.show()
    
    # Function to handle UART data display
    def handle_uart_data_display():
        global current_selection
        oled.fill(0)  # Clear the display
        write20.text("Receiving Data...", 0, 0)
        oled.show()
    
        while True:
            if uart.any():
                data = uart.readline()
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
                # Respond based on received UART commands
                if data.startswith(b'<<INITIALIZE'):
                    led.toggle()  # Toggle LED for debug
                    uart.write(b'Initialized\r\n')  # Send response
                elif data.startswith(b'<<CANCEL'):
                    led.toggle()
                    uart.write(b'Cancelled\r\n')  # Send response
                elif data.startswith(b'<<START TEST'):
                    led.toggle()
                    uart.write(b'Starting Test\r\n')  # Send response
                elif data.startswith(b'wei.zrp'):
                    led.toggle()
                    uart.write(b'wei.zrp Zero Emulated\r\n')  # Send response
                    utime.sleep(1)
                elif data.startswith(b'wei.mdf'):
                    led.toggle()
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    response = f"wei.mdf.A:RAW:+ 20617;1;ST;GS;GRO:+ {cellValue};NET:+ 0.000;TAR:+ 0.000;{randEndValue}e\r\n"
                    uart.write(response.encode())  # Send response
                    print("Sent response:", response)  # Debug print
    
            # Check if the rotary encoder button is pressed
            if SW.value() == 0:  # If the switch button is pressed
                utime.sleep(0.1)  # Debounce delay
                break
    
    # Function to display Instructions
    def instructions():
        oled.fill(0)
        write20.text("Instructions:", 0, 0)
        write15.text("1. Step A", 0, 20)
        write15.text("2. Step B", 0, 30)
        write15.text("3. Step C", 0, 40)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function to display Setup Menu
    def setup():
        oled.fill(0)
        write20.text("Setup Menu", 0, 0)
        write15.text("Configure options", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Calibration Menu
    def calibration():
        oled.fill(0)
        write20.text("Calibration Menu", 0, 0)
        write15.text("Adjust settings", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Help Menu
    def help_menu():
        oled.fill(0)
        write20.text("Help Menu", 0, 0)
        write15.text("Help information", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Data":
                    handle_uart_data_display()  # Enter data receiving mode
                elif menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Display current menu
            display_menu()  # Refresh the menu display
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    
        except KeyboardInterrupt:
            break
    

    Code Components Explained:

    1. UART Initialization: The UART interface is initialized for communication.

    2. Menu Structure: The menu allows navigation for "Data" and other options like "Instructions", "Setup", "Calibration", and "Help".

    3. Serial Data Handling: The code continuously listens for incoming UART commands when "Data" is selected, processing these commands and sending appropriate responses.

    4. Non-Blocking Menu Options: Each menu option that displays instructions, setup info, calibration, or help waits for the user to press the switch button before returning to the main menu, avoiding any locking or unresponsive behavior.

    5. OLED Display Updates: Functions are provided to update the OLED display for both the menu and UART data.

    Testing

    • Upload the code to your microcontroller.
    • Use a serial terminal application to send commands and observe responses for confirmation of UART functionality.
    • Navigate through the menu options, ensuring you can return to the main menu promptly after viewing other information.

    This setup should now fully meet your requirements. If there are any further changes or issues you'd like to address, let me know!

  21. User

    working. please add this data to the display of data sent print("Sent response:", response) # Debug print

  22. Assistant

    To display the response sent over UART on the OLED screen right after sending it, you can modify the handle_uart_data_display() function to include a call to a display function for the sent response.

    Below is the code with the necessary modifications to show the sent data on the OLED display as well:

    Full Code with Sent Response Display

    from machine import UART, Pin, I2C
    from ssd1306 import SSD1306_I2C
    import utime
    from oled import Write, GFX
    from oled.fonts import ubuntu_mono_15, ubuntu_mono_20
    from rotary_irq_rp2 import RotaryIRQ
    from random import randrange
    
    # Initialize UART and other peripherals
    uart = UART(1, timeout=100, baudrate=56000, tx=Pin(4), rx=Pin(5), bits=8, parity=None, stop=1)
    led = Pin(25, Pin.OUT)
    
    SW = Pin(20, Pin.IN, Pin.PULL_UP)
    r = RotaryIRQ(pin_num_clk=18, pin_num_dt=19, min_val=0, reverse=False, range_mode=RotaryIRQ.RANGE_UNBOUNDED)
    
    val_old = r.value()
    menu_options = ["Data", "Instructions", "Setup", "Calibration", "Help"]
    current_selection = 0  # Start with the first menu item
    
    # Push button setup
    butPinValueUp = 14
    myButtonValueUp = Pin(butPinValueUp, Pin.IN, Pin.PULL_UP)
    
    butPinValueDown = 13
    myButtonValueDown = Pin(butPinValueDown, Pin.IN, Pin.PULL_UP)
    
    butPinValueReset = 10
    myButtonValueReset = Pin(butPinValueReset, Pin.IN, Pin.PULL_UP)
    
    # OLED and I2C setup
    i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
    oled = SSD1306_I2C(128, 64, i2c)
    gfx = GFX(128, 64, oled.pixel)
    
    # Fonts
    write15 = Write(oled, ubuntu_mono_15)
    write20 = Write(oled, ubuntu_mono_20)
    
    # Initial display
    oled.fill(0)
    write20.text("JMS AERO AG", 7, 0)
    write20.text("Data Logger", 7, 20)
    write20.text("Simulator", 19, 40)
    oled.show()
    utime.sleep(5)
    
    # Clear the display after the initial screen
    oled.fill(0)
    oled.show()
    
    # Function to display the menu
    def display_menu():
        oled.fill(0)  # Clear the display
        for i, option in enumerate(menu_options):
            if i == current_selection:
                oled.text(">" + option, 10, i * 10)  # Highlight selected option
            else:
                oled.text(option, 10, i * 10)
        oled.show()
    
    # Function to display UART data on OLED
    def display_uart_data(data):
        oled.fill(0)  # Clear the display for new data
        write20.text("UART Data:", 0, 0)
        oled.text(data.decode().strip(), 0, 20)  # Display the updated UART message
        oled.show()
    
    # Function to display sent response
    def display_sent_response(response):
        oled.fill(0)  # Clear the display for new data
        write20.text("Sent Response:", 0, 0)
        oled.text(response.decode().strip(), 0, 20)  # Display the sent response
        oled.show()
    
    # Function to handle UART data display
    def handle_uart_data_display():
        global current_selection
        oled.fill(0)  # Clear the display
        write20.text("Receiving Data...", 0, 0)
        oled.show()
    
        while True:
            if uart.any():
                data = uart.readline()
                print("Received UART data:", data)  # Debug print
                display_uart_data(data)  # Display the received data on the OLED
    
                # Respond based on received UART commands
                if data.startswith(b'<<INITIALIZE'):
                    led.toggle()  # Toggle LED for debug
                    uart.write(b'Initialized\r\n')  # Send response
                elif data.startswith(b'<<CANCEL'):
                    led.toggle()
                    uart.write(b'Cancelled\r\n')  # Send response
                elif data.startswith(b'<<START TEST'):
                    led.toggle()
                    uart.write(b'Starting Test\r\n')  # Send response
                elif data.startswith(b'wei.zrp'):
                    led.toggle()
                    uart.write(b'wei.zrp Zero Emulated\r\n')  # Send response
                    utime.sleep(1)
                elif data.startswith(b'wei.mdf'):
                    led.toggle()
                    randEndValue = randrange(9)  # Generate a random number (0-8)
                    cellValue = 100000  # Example value
                    response = f"wei.mdf.A:RAW:+ 20617;1;ST;GS;GRO:+ {cellValue};NET:+ 0.000;TAR:+ 0.000;{randEndValue}e\r\n"
                    uart.write(response.encode())  # Send response
                    print("Sent response:", response)  # Debug print
                    display_sent_response(response.encode())  # Display sent response
    
            # Check if the rotary encoder button is pressed
            if SW.value() == 0:  # If the switch button is pressed
                utime.sleep(0.1)  # Debounce delay
                break
    
    # Function to display Instructions
    def instructions():
        oled.fill(0)
        write20.text("Instructions:", 0, 0)
        write15.text("1. Step A", 0, 20)
        write15.text("2. Step B", 0, 30)
        write15.text("3. Step C", 0, 40)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function to display Setup Menu
    def setup():
        oled.fill(0)
        write20.text("Setup Menu", 0, 0)
        write15.text("Configure options", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Calibration Menu
    def calibration():
        oled.fill(0)
        write20.text("Calibration Menu", 0, 0)
        write15.text("Adjust settings", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Function for Help Menu
    def help_menu():
        oled.fill(0)
        write20.text("Help Menu", 0, 0)
        write15.text("Help information", 0, 20)
        write15.text("Press SW to exit", 0, 55)
        oled.show()
        while SW.value() == 1:  # Wait for button press to exit
            utime.sleep(0.1)  # Reduce CPU usage in the loop
    
    # Main loop for handling buttons and rotary encoder
    while True:
        try:
            # Check rotary encoder
            val_new = r.value()
            if val_old != val_new:
                # Update current selection
                current_selection = (current_selection + (val_new - val_old)) % len(menu_options)
                val_old = val_new
                display_menu()  # Update display only when the selection changes
    
            # Select menu item
            if SW.value() == 0:  # If the switch button is pressed
                print("Selected:", menu_options[current_selection])
                if menu_options[current_selection] == "Data":
                    handle_uart_data_display()  # Enter data receiving mode
                elif menu_options[current_selection] == "Instructions":
                    instructions()
                elif menu_options[current_selection] == "Setup":
                    setup()
                elif menu_options[current_selection] == "Calibration":
                    calibration()
                elif menu_options[current_selection] == "Help":
                    help_menu()
    
            # Display current menu
            display_menu()  # Refresh the menu display
            utime.sleep_ms(100)  # Small delay to prevent excessive CPU usage
    
        except KeyboardInterrupt:
            break
    

    Key Modifications:

    1. New Function display_sent_response(response): This function is created to display the sent UART response on the OLED. It takes the response string, clears the display, and shows the formatted response received from the UART in a dedicated area.

    2. Call to display_sent_response(): After constructing the response string in the handle_uart_data_display() function, the code now calls display_sent_response(response.encode()) to show the sent response on the OLED display right after it is sent.

    Expected Behavior:

    • When a command is received and processed that generates a response (like wei.mdf), the LED will toggle, and the response will be sent back via UART.
    • Alongside that, the OLED display will show the response sent, providing real-time feedback on the actions taken by the device.

    Load this complete code onto your microcontroller, and it should function according to your specifications. Let me know if you need further adjustments!