Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-mini-2024-07-18· OpenAIAi2 WildChat-4.8M (AI2)

1-strictly utilise geany for every edits. 2-need strictly os to boot in "tlp bat" mode.…

  1. User

    1-strictly utilise geany for every edits.

    2-need strictly os to boot in "tlp bat" mode.

    (got some hdd being unmounted for all hdd disks and "tlp" is in bat mode "sudo tlp bat" running. one hdd disk constantly power ons itself after 10mins period and then shutting down indefinitely in circles, while others stay turned off.

    that could be a behaviour of S.M.A.R.T. enabled in bios which for some hdd model leaving it off and other hdd in some timeout triggers with through bios S.M.A.R.T.)

    figure-out it in config which makes one hdd to power up/down through each 10 mins indefinitely:

    """

    ------------------------------------------------------------------------------

    /etc/tlp.conf - TLP user configuration (version 1.6.1)

    See full explanation: https://linrunner.de/tlp/settings

    Copyright (c) 2023 Thomas Koch and others.

    SPDX-License-Identifier: GPL-2.0-or-later

    Settings are read in the following order:

    1. Intrinsic defaults

    2. /etc/tlp.d/*.conf - Drop-in customization snippets

    3. /etc/tlp.conf - User configuration (this file)

    Notes:

    - In case of identical parameters, the last occurence has precedence

    - This also means, parameters enabled here will override anything else

    - However you may append values to a parameter already defined as intrinsic

    default or in a previously read file: use PARAMETER+="add values"

    - IMPORTANT: all parameters here are disabled; remove the leading '#' if you

    like to enable a feature without default or have a value different from the

    default

    - Default *: intrinsic default that is effective when the parameter is missing

    or disabled by a leading '#'; use PARAM="" to disable an intrinsic default

    - Default : do nothing or use kernel/hardware defaults

    - IMPORTANT: parameters must always be specified pairwise i.e. for

    both AC and BAT. Omitting one of the two makes the set value effective for

    both power sources, since a change only occurs when different values are

    defined.

    ------------------------------------------------------------------------------

    tlp - Parameters for power saving

    Set to 0 to disable, 1 to enable TLP.

    Default: 1

    #TLP_ENABLE=1

    Control how warnings about invalid settings are issued:

    0=disabled,

    1=background tasks (boot, resume, change of power source) report to syslog,

    2=shell commands report to the terminal (stderr),

    3=combination of 1 and 2

    Default: 3

    #TLP_WARN_LEVEL=3

    Operation mode when no power supply can be detected: AC, BAT.

    Concerns some desktop and embedded hardware only.

    Default:

    #TLP_DEFAULT_MODE=AC

    Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE

    Note: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.

    Default: 0

    #TLP_PERSISTENT_DEFAULT=0

    Power supply classes to ignore when determining operation mode: AC, USB, BAT.

    Separate multiple classes with spaces.

    Note: try on laptops where operation mode AC/BAT is incorrectly detected.

    Default:

    #TLP_PS_IGNORE="BAT"

    Seconds laptop mode has to wait after the disk goes idle before doing a sync.

    Non-zero value enables, zero disables laptop mode.

    Default: 0 (AC), 2 (BAT)

    #DISK_IDLE_SECS_ON_AC=0 #DISK_IDLE_SECS_ON_BAT=2

    Dirty page values (timeouts in secs).

    Default: 15 (AC), 60 (BAT)

    #MAX_LOST_WORK_SECS_ON_AC=15 #MAX_LOST_WORK_SECS_ON_BAT=60

    Select a CPU scaling driver operation mode.

    Intel CPU with intel_pstate driver:

    active, passive.

    AMD Zen 2 or newer CPU with amd-pstate_driver as of kernel 6.3/6.4(*):

    active, passive, guided(*).

    Default:

    #CPU_DRIVER_OPMODE_ON_AC=active #CPU_DRIVER_OPMODE_ON_BAT=active

    Select a CPU frequency scaling governor.

    Intel CPU with intel_pstate driver or

    AMD CPU with amd-pstate driver in active mode ('amd-pstate-epp'):

    performance, powersave(*).

    Intel CPU with intel_pstate driver in passive mode ('intel_cpufreq') or

    AMD CPU with amd-pstate driver in passive or guided mode ('amd-pstate') or

    Intel, AMD and other CPU brands with acpi-cpufreq driver:

    conservative, ondemand(), userspace, powersave, performance, schedutil().

    Use tlp-stat -p to show the active driver and available governors.

    Important:

    Governors marked (*) above are power efficient for almost all workloads

    and therefore kernel and most distributions have chosen them as defaults.

    You should have done your research about advantages/disadvantages before

    changing the governor.

    Default:

    #CPU_SCALING_GOVERNOR_ON_AC=powersave #CPU_SCALING_GOVERNOR_ON_BAT=powersave

    Set the min/max frequency available for the scaling governor.

    Possible values depend on your CPU. For available frequencies see

    the output of tlp-stat -p.

    Notes:

    - Min/max frequencies must always be specified for both AC and BAT

    - Not recommended for use with the intel_pstate driver, use

    CPU_MIN/MAX_PERF_ON_AC/BAT below instead

    Default:

    #CPU_SCALING_MIN_FREQ_ON_AC=0 #CPU_SCALING_MAX_FREQ_ON_AC=0 #CPU_SCALING_MIN_FREQ_ON_BAT=0 #CPU_SCALING_MAX_FREQ_ON_BAT=0

    Set CPU energy/performance policies EPP and EPB:

    performance, balance_performance, default, balance_power, power.

    Values are given in order of increasing power saving.

    Requires:

    * Intel CPU

    EPP: Intel Core i 6th gen. or newer CPU with intel_pstate driver

    EPB: Intel Core i 2nd gen. or newer CPU with intel_pstate driver

    as of kernel 5.2; alternatively module msr and

    x86_energy_perf_policy from linux-tools

    EPP and EPB are mutually exclusive: when EPP is available, Intel CPUs

    will not honor EPB. Only the matching feature will be applied by TLP.

    * AMD Zen 2 or newer CPU

    EPP: amd-pstate driver in active mode ('amd-pstate-epp') as of kernel 6.3

    Default: balance_performance (AC), balance_power (BAT)

    #CPU_ENERGY_PERF_POLICY_ON_AC=balance_performance #CPU_ENERGY_PERF_POLICY_ON_BAT=balance_power

    Set Intel CPU P-state performance: 0..100 (%).

    Limit the max/min P-state to control the power dissipation of the CPU.

    Values are stated as a percentage of the available performance.

    Requires Intel Core i 2nd gen. or newer CPU with intel_pstate driver.

    Default:

    #CPU_MIN_PERF_ON_AC=0 #CPU_MAX_PERF_ON_AC=100 #CPU_MIN_PERF_ON_BAT=0 #CPU_MAX_PERF_ON_BAT=30

    Set the CPU "turbo boost" (Intel) or "turbo core" (AMD) feature:

    0=disable, 1=allow.

    Allows to raise the maximum frequency/P-state of some cores if the

    CPU chip is not fully utilized and below it's intended thermal budget.

    Note: a value of 1 does not activate boosting, it just allows it.

    Default:

    #CPU_BOOST_ON_AC=1 #CPU_BOOST_ON_BAT=0

    Set Intel/AMD CPU dynamic boost feature:

    0=disable, 1=enable.

    Improve performance by increasing minimum P-state limit dynamically

    whenever a task previously waiting on I/O is selected to run.

    Requires:

    * Intel Core i 6th gen. or newer CPU: intel_pstate driver in active mode

    * AMD Zen 2 or newer CPU: amd-pstate driver in active mode ('amd-pstate-epp')

    provided by a yet unreleased kernel 6.x

    Default:

    #CPU_HWP_DYN_BOOST_ON_AC=1 #CPU_HWP_DYN_BOOST_ON_BAT=0

    Kernel NMI Watchdog:

    0=disable (default, saves power), 1=enable (for kernel debugging only).

    Default: 0

    #NMI_WATCHDOG=0

    Select platform profile:

    performance, balanced, low-power.

    Controls system operating characteristics around power/performance levels,

    thermal and fan speed. Values are given in order of increasing power saving.

    Note: check the output of tlp-stat -p to determine availability on your

    hardware and additional profiles such as: balanced-performance, quiet, cool.

    Default:

    #PLATFORM_PROFILE_ON_AC=performance #PLATFORM_PROFILE_ON_BAT=low-power

    System suspend mode:

    s2idle: Idle standby - a pure software, light-weight, system sleep state,

    deep: Suspend to RAM - the whole system is put into a low-power state,

    except for memory, usually resulting in higher savings than s2idle.

    CAUTION: changing suspend mode may lead to system instability and even

    data loss. As for the availability of different modes on your system,

    check the output of tlp-stat -s. If unsure, stick with the system default

    by not enabling this.

    Default:

    #MEM_SLEEP_ON_AC=s2idle #MEM_SLEEP_ON_BAT=deep

    Define disk devices on which the following DISK/AHCI_RUNTIME parameters act.

    Separate multiple devices with spaces.

    Devices can be specified by disk ID also (lookup with: tlp diskid).

    Default: "nvme0n1 sda"

    #DISK_DEVICES="nvme0n1 sda"

    Disk advanced power management level: 1..254, 255 (max saving, min, off).

    Levels 1..127 may spin down the disk; 255 allowable on most drives.

    Separate values for multiple disks with spaces. Use the special value 'keep'

    to keep the hardware default for the particular disk.

    Default: 254 (AC), 128 (BAT)

    #DISK_APM_LEVEL_ON_AC="254 254" #DISK_APM_LEVEL_ON_BAT="128 128"

    Exclude disk classes from advanced power management (APM):

    sata, ata, usb, ieee1394.

    Separate multiple classes with spaces.

    CAUTION: USB and IEEE1394 disks may fail to mount or data may get corrupted

    with APM enabled. Be careful and make sure you have backups of all affected

    media before removing 'usb' or 'ieee1394' from the denylist!

    Default: "usb ieee1394"

    #DISK_APM_CLASS_DENYLIST="usb ieee1394"

    Hard disk spin down timeout:

    0: spin down disabled

    1..240: timeouts from 5s to 20min (in units of 5s)

    241..251: timeouts from 30min to 5.5 hours (in units of 30min)

    See 'man hdparm' for details.

    Separate values for multiple disks with spaces. Use the special value 'keep'

    to keep the hardware default for the particular disk.

    Default:

    #DISK_SPINDOWN_TIMEOUT_ON_AC="0 0" #DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"

    Select I/O scheduler for the disk devices.

    Multi queue (blk-mq) schedulers:

    mq-deadline(*), none, kyber, bfq

    Single queue schedulers:

    deadline(*), cfq, bfq, noop

    (*) recommended.

    Separate values for multiple disks with spaces. Use the special value 'keep'

    to keep the kernel default scheduler for the particular disk.

    Notes:

    - Multi queue (blk-mq) may need kernel boot option 'scsi_mod.use_blk_mq=1'

    and 'modprobe mq-deadline-iosched|kyber|bfq' on kernels < 5.0

    - Single queue schedulers are legacy now and were removed together with

    the old block layer in kernel 5.0

    Default: keep

    #DISK_IOSCHED="mq-deadline mq-deadline"

    AHCI link power management (ALPM) for SATA disks:

    min_power, med_power_with_dipm(*), medium_power, max_performance.

    (*) recommended.

    Multiple values separated with spaces are tried sequentially until success.

    Default: med_power_with_dipm (AC & BAT)

    #SATA_LINKPWR_ON_AC="med_power_with_dipm" #SATA_LINKPWR_ON_BAT="med_power_with_dipm"

    Exclude SATA links from AHCI link power management (ALPM).

    SATA links are specified by their host. Refer to the output of

    tlp-stat -d to determine the host; the format is "hostX".

    Separate multiple hosts with spaces.

    Default:

    #SATA_LINKPWR_DENYLIST="host1"

    Runtime Power Management for NVMe, SATA, ATA and USB disks

    as well as SATA ports:

    on=disable, auto=enable.

    Note: SATA controllers are PCIe bus devices and handled by RUNTIME_PM further

    down.

    Default: on (AC), auto (BAT)

    #AHCI_RUNTIME_PM_ON_AC=on #AHCI_RUNTIME_PM_ON_BAT=auto

    Seconds of inactivity before disk is suspended.

    Note: effective only when AHCI_RUNTIME_PM_ON_AC/BAT is activated.

    Default: 15

    #AHCI_RUNTIME_PM_TIMEOUT=15

    Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.

    Drive can be powered on again by releasing (and reinserting) the eject lever

    or by pressing the disc eject button on newer models.

    Note: an UltraBay/MediaBay hard disk is never powered off.

    Default: 0

    #BAY_POWEROFF_ON_AC=0 #BAY_POWEROFF_ON_BAT=0

    Optical drive device to power off

    Default: sr0

    #BAY_DEVICE="sr0"

    Set the min/max/turbo frequency for the Intel GPU.

    Possible values depend on your hardware. For available frequencies see

    the output of tlp-stat -g.

    Default:

    #INTEL_GPU_MIN_FREQ_ON_AC=0 #INTEL_GPU_MIN_FREQ_ON_BAT=0 #INTEL_GPU_MAX_FREQ_ON_AC=0 #INTEL_GPU_MAX_FREQ_ON_BAT=0 #INTEL_GPU_BOOST_FREQ_ON_AC=0 #INTEL_GPU_BOOST_FREQ_ON_BAT=0

    AMD GPU power management.

    Performance level (DPM): auto, low, high; auto is recommended.

    Note: requires amdgpu or radeon driver.

    Default: auto

    #RADEON_DPM_PERF_LEVEL_ON_AC=auto #RADEON_DPM_PERF_LEVEL_ON_BAT=auto

    Dynamic power management method (DPM): balanced, battery, performance.

    Note: radeon driver only.

    Default:

    #RADEON_DPM_STATE_ON_AC=performance #RADEON_DPM_STATE_ON_BAT=battery

    Graphics clock speed (profile method): low, mid, high, auto, default;

    auto = mid on BAT, high on AC.

    Note: radeon driver on legacy ATI hardware only (where DPM is not available).

    Default: default

    #RADEON_POWER_PROFILE_ON_AC=default #RADEON_POWER_PROFILE_ON_BAT=default

    Wi-Fi power saving mode: on=enable, off=disable.

    Default: off (AC), on (BAT)

    #WIFI_PWR_ON_AC=off #WIFI_PWR_ON_BAT=on

    Disable Wake-on-LAN: Y/N.

    Default: Y

    #WOL_DISABLE=Y

    Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).

    A value of 0 disables, >= 1 enables power saving.

    Note: 1 is recommended for Linux desktop environments with PulseAudio,

    systems without PulseAudio may require 10.

    Default: 1

    #SOUND_POWER_SAVE_ON_AC=1 #SOUND_POWER_SAVE_ON_BAT=1

    Disable controller too (HDA only): Y/N.

    Note: effective only when SOUND_POWER_SAVE_ON_AC/BAT is activated.

    Default: Y

    #SOUND_POWER_SAVE_CONTROLLER=Y

    PCIe Active State Power Management (ASPM):

    default(*), performance, powersave, powersupersave.

    (*) keeps BIOS ASPM defaults (recommended)

    Default:

    #PCIE_ASPM_ON_AC=default #PCIE_ASPM_ON_BAT=default

    Runtime Power Management for PCIe bus devices: on=disable, auto=enable.

    Default: on (AC), auto (BAT)

    #RUNTIME_PM_ON_AC=on #RUNTIME_PM_ON_BAT=auto

    Exclude listed PCIe device adresses from Runtime PM.

    Note: this preserves the kernel driver default, to force a certain state

    use RUNTIME_PM_ENABLE/DISABLE instead.

    Separate multiple addresses with spaces.

    Use lspci to get the adresses (1st column).

    Default:

    #RUNTIME_PM_DENYLIST="11:22.3 44:55.6"

    Exclude PCIe devices assigned to the listed drivers from Runtime PM.

    Note: this preserves the kernel driver default, to force a certain state

    use RUNTIME_PM_ENABLE/DISABLE instead.

    Separate multiple drivers with spaces.

    Default: "mei_me nouveau radeon", use "" to disable completely.

    #RUNTIME_PM_DRIVER_DENYLIST="mei_me nouveau radeon"

    Permanently enable/disable Runtime PM for listed PCIe device addresses

    (independent of the power source). This has priority over all preceding

    Runtime PM settings. Separate multiple addresses with spaces.

    Use lspci to get the adresses (1st column).

    Default:

    #RUNTIME_PM_ENABLE="11:22.3" #RUNTIME_PM_DISABLE="44:55.6"

    Set to 0 to disable, 1 to enable USB autosuspend feature.

    Default: 1

    #USB_AUTOSUSPEND=1

    Exclude listed devices from USB autosuspend (separate with spaces).

    Use lsusb to get the ids.

    Note: input devices (usbhid) and libsane-supported scanners are excluded

    automatically.

    Default:

    #USB_DENYLIST="1111:2222 3333:4444"

    Exclude audio devices from USB autosuspend:

    0=do not exclude, 1=exclude.

    Default: 1

    #USB_EXCLUDE_AUDIO=1

    Exclude bluetooth devices from USB autosuspend:

    0=do not exclude, 1=exclude.

    Default: 0

    #USB_EXCLUDE_BTUSB=0

    Exclude phone devices from USB autosuspend:

    0=do not exclude, 1=exclude (enable charging).

    Default: 0

    #USB_EXCLUDE_PHONE=0

    Exclude printers from USB autosuspend:

    0=do not exclude, 1=exclude.

    Default: 1

    #USB_EXCLUDE_PRINTER=1

    Exclude WWAN devices from USB autosuspend:

    0=do not exclude, 1=exclude.

    Default: 0

    #USB_EXCLUDE_WWAN=0

    Allow USB autosuspend for listed devices even if already denylisted or

    excluded above (separate with spaces). Use lsusb to get the ids.

    Default: 0

    #USB_ALLOWLIST="1111:2222 3333:4444"

    Set to 1 to disable autosuspend before shutdown, 0 to do nothing

    Note: use as a workaround for USB devices that cause shutdown problems.

    Default: 0

    #USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=0

    Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown

    on system startup: 0=disable, 1=enable.

    Note: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below

    are ignored when this is enabled.

    Default: 0

    #RESTORE_DEVICE_STATE_ON_STARTUP=0

    Radio devices to disable on startup: bluetooth, nfc, wifi, wwan.

    Separate multiple devices with spaces.

    Default:

    #DEVICES_TO_DISABLE_ON_STARTUP="bluetooth nfc wifi wwan"

    Radio devices to enable on startup: bluetooth, nfc, wifi, wwan.

    Separate multiple devices with spaces.

    Default:

    #DEVICES_TO_ENABLE_ON_STARTUP="wifi"

    Radio devices to disable on shutdown: bluetooth, nfc, wifi, wwan.

    Note: use as a workaround for devices that are blocking shutdown.

    Default:

    #DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth nfc wifi wwan"

    Radio devices to enable on shutdown: bluetooth, nfc, wifi, wwan.

    (to prevent other operating systems from missing radios).

    Default:

    #DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"

    Radio devices to enable on AC: bluetooth, nfc, wifi, wwan.

    Default:

    #DEVICES_TO_ENABLE_ON_AC="bluetooth nfc wifi wwan"

    Radio devices to disable on battery: bluetooth, nfc, wifi, wwan.

    Default:

    #DEVICES_TO_DISABLE_ON_BAT="bluetooth nfc wifi wwan"

    Radio devices to disable on battery when not in use (not connected):

    bluetooth, nfc, wifi, wwan.

    Default:

    #DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth nfc wifi wwan"

    Battery Care -- Charge thresholds

    Charging starts when the charger is connected and the charge level

    is below the start threshold. Charging stops when the charge level

    is above the stop threshold.

    Required hardware: Lenovo ThinkPads and select other laptop brands

    are driven via specific plugins

    - Active plugin and support status are shown by tlp-stat -b

    - Vendor specific threshold levels are shown by tlp-stat -b, some

    laptops support only 1 (on)/ 0 (off) instead of a percentage level

    - When your hardware supports a start and a stop threshold, you must

    specify both, otherwise TLP will refuse to apply the single threshold

    - When your hardware supports only a stop threshold, set the start

    value to 0

    - Older ThinkPads may require an external kernel module, refer to the

    output of tlp-stat -b

    For further explanation and vendor specific details refer to

    - https://linrunner.de/tlp/settings/battery.html

    - https://linrunner.de/tlp/settings/bc-vendors.html

    BAT0: Primary / Main / Internal battery

    Note: also use for batteries BATC, BATT and CMB0

    Default:

    Battery charge level below which charging will begin.

    #START_CHARGE_THRESH_BAT0=75

    Battery charge level above which charging will stop.

    #STOP_CHARGE_THRESH_BAT0=80

    BAT1: Secondary / Ultrabay / Slice / Replaceable battery

    Note: primary on some laptops

    Default:

    Battery charge level below which charging will begin.

    #START_CHARGE_THRESH_BAT1=75

    Battery charge level above which charging will stop.

    #STOP_CHARGE_THRESH_BAT1=80

    Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.

    Default: 0

    #RESTORE_THRESHOLDS_ON_BAT=1

    Control battery care drivers: 0=disable, 1=enable.

    Default: 1 (all)

    #NATACPI_ENABLE=1 #TPACPI_ENABLE=1 #TPSMAPI_ENABLE=1

    ------------------------------------------------------------------------------

    tlp-rdw - Parameters for the radio device wizard

    Possible devices: bluetooth, wifi, wwan.

    Separate multiple radio devices with spaces.

    Default: (for all parameters below)

    Radio devices to disable on connect.

    #DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan" #DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan" #DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"

    Radio devices to enable on disconnect.

    #DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan" #DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT="" #DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""

    Radio devices to enable/disable when docked.

    #DEVICES_TO_ENABLE_ON_DOCK="" #DEVICES_TO_DISABLE_ON_DOCK=""

    Radio devices to enable/disable when undocked.

    #DEVICES_TO_ENABLE_ON_UNDOCK="wifi" #DEVICES_TO_DISABLE_ON_UNDOCK=""

    """.

  2. Assistant

    To troubleshoot the issue of one hard drive (HDD) frequently powering on and off every 10 minutes in a system running TLP in battery mode (sudo tlp bat), you can examine a few specific parameters in your TLP configuration file (/etc/tlp.conf).

    Here’s a summary of possible configurations that could potentially be causing the behavior you're observing, along with recommendations for adjustments:

    Key TLP Parameters

    1. Disk Spin Down Timeout

      • The parameters DISK_SPINDOWN_TIMEOUT_ON_AC and DISK_SPINDOWN_TIMEOUT_ON_BAT determine how long the HDD should wait before going to sleep (spindown).
      • By default, they are set to 0 (no spin down) and may not be explicitly configured in your current settings.
      • Suggested change:
        DISK_SPINDOWN_TIMEOUT_ON_BAT="12" # Adjust to your desired timeout, in multiples of 5 seconds.
        
    2. Advanced Power Management Level

      • The parameter DISK_APM_LEVEL_ON_BAT determines the advanced power management level for the drives.
      • It might be worth adjusting this to control power behavior effectively, especially for drives that aren’t in constant use.
      • Suggested change:
        DISK_APM_LEVEL_ON_BAT="128 128" # Adjust levels based on your HDD model specifications.
        
    3. Hard Disk Devices

      • Ensure that the DISK_DEVICES is accurately listing all the disks (HDDs) you want to manage. If not specified, TLP might not apply settings correctly to all HDDs.
      • Suggested change:
        DISK_DEVICES="sda sdb" # Replace sda and sdb with your actual HDD identifiers.
        
    4. Runtime Power Management

      • The AHCI_RUNTIME_PM_ON_BAT and AHCI_RUNTIME_PM_TIMEOUT settings can impact how quickly the disks go into a low-power state.
      • Suggested change:
        AHCI_RUNTIME_PM_ON_BAT=auto
        AHCI_RUNTIME_PM_TIMEOUT=15
        

    Investigating SMART Settings

    • If the disks have SMART (Self-Monitoring, Analysis, and Reporting Technology) enabled in your BIOS, it could influence how they behave. The constant powering on might be due to SMART self-tests or monitoring.
      • Check your BIOS settings to see if you can disable SMART features or set specific configurations related to its behavior.

    Device-Specific Configurations

    • Each HDD may have its own characteristics regarding power management. Investigate if the specific HDD is known for such behaviors (you can research on forums or the manufacturer's data).
    • You may also need to consider using specific HDD tools or commands (like using hdparm) if further configuration is necessary.

    Monitoring and Testing

    • After making changes, monitor the HDD status over a period to see if the on-off cycle occurs again. Use tools like tlp-stat to review power settings and smartctl to review the HDD's SMART status.

    Final Steps

    Once you adjust any of the configuration parameters, make sure to restart TLP with:

    sudo tlp restart
    

    Then check the effects and observe if the HDD still powers up and down every 10 minutes. If the problem persists, further diagnosis might be required, potentially involving hardware checks or investigating if any background processes are accessing the HDD.