Problem 1: Configuration Space for a Two-Link Manipulator (4 points) Task: Create the…
- User
Problem 1: Configuration Space for a Two-Link Manipulator (4 points)
Task: Create the configuration space (C-Space) for the robot with an obstacle as shown in Figure 1a.
You can either:- Use a computer program (like Matlab) to generate the C-Space, or
- Use hand calculations to create a rough plot of the C-Space.
Hint: Consider a collision if any of the two links ( o_1 ) or ( o_2 ) hits the obstacle. The joint angles for the manipulator are constrained as:
- ( 0 \leq q_1 \leq \pi/2 )
- ( 0 \leq q_2 \leq \pi )
Figure 1a: Shows a two-link manipulator with a circular obstacle.
Figure 1b: Shows the C-Space of the manipulator with a point obstacle. - Assistant
To create the configuration space (C-Space) for a two-link manipulator with a circular obstacle, we need to define the parameters and constraints clearly, along with how the manipulator behaves in relation to the obstacle.
Joint Angles and Configuration
-
Joint Angles:
- ( q_1 ): Angle of the first link with respect to the vertical, constrained to ( [0, \frac{\pi}{2}] ).
- ( q_2 ): Angle of the second link with respect to the first link’s orientation, constrained to ( [0, \pi] ).
-
Link Lengths:
- Let ( L_1 ) be the length of the first link.
- Let ( L_2 ) be the length of the second link.
-
Obstacle:
- Assume a circular obstacle with a center at ( (x_o, y_o) ) and radius ( r ).
Position of the End Effector
The position ((x, y)) of the end effector (the tip of the second link) can be calculated using forward kinematics: [ x = L_1 \cos(q_1) + L_2 \cos(q_1 + q_2) ] [ y = L_1 \sin(q_1) + L_2 \sin(q_1 + q_2) ]
Collision Condition
The end effector collides with the obstacle if the distance between the end effector and the center of the obstacle is less than the radius of the obstacle: [ \sqrt{(x - x_o)^2 + (y - y_o)^2} \leq r ]
C-Space Analysis
- Region of Valid Configuration: The area corresponding to combinations of ( (q_1, q_2) ) such that the above collision condition does not hold.
- Grid Sampling: To visualize this C-Space, we can uniformly sample ( q_1 ) ranging from ( 0 ) to ( \frac{\pi}{2} ) and ( q_2 ) from ( 0 ) to ( \pi ). At each sampled pair ( (q_1, q_2) ):
- Calculate the position of the end effector.
- Check for collision with the obstacle.
Example Calculations
Let's assume:
- ( L_1 = 1 ) unit
- ( L_2 = 1 ) unit
- Circular obstacle at ( (1, 1) ) with radius ( 0.2 ).
Sample Calculations:
-
For ( q_1 = 0 ), ( q_2 = 0 ): [ x = 1 \cos(0) + 1 \cos(0) = 2 ] [ y = 1 \sin(0) + 1 \sin(0) = 0 ]
Distance to obstacle: ( \sqrt{(2-1)^2 + (0-1)^2} = \sqrt{1 + 1} = \sqrt{2} \approx 1.41) (No Collision).
-
For ( q_1 = \frac{\pi}{4} ), ( q_2 = \frac{\pi}{4} ): [ x = 1 \cos\left(\frac{\pi}{4}\right) + 1 \cos\left(\frac{3\pi}{4}\right) = \frac{\sqrt{2}}{2} + (-\frac{\sqrt{2}}{2}) = 0 ] [ y = 1 \sin\left(\frac{\pi}{4}\right) + 1 \sin\left(\frac{3\pi}{4}\right) = \frac{\sqrt{2}}{2} + \frac{\sqrt{2}}{2} = \sqrt{2} \approx 1.41 ]
Distance: ( \sqrt{(0-1)^2 + (1.41-1)^2} \approx 0.41) (Collision).
C-Space Visualization
Using the above calculations, you would create a plot:
- Create a 2D plot with ( q_1 ) on one axis and ( q_2 ) on the other.
- Mark valid configurations (no collision) in one color and invalid configurations (with collision) in another color.
Recommendations for a Programmatic Approach
- Use a computer program such as MATLAB, Python, or any other simulation software that allows for graphical plotting.
- Create a meshgrid for the angles ( q_1 ) and ( q_2 ).
- Iterate through each angle pair, compute the end-effector position, and check for collisions to populate the C-Space.
This will yield a visual representation of the workspace available to the manipulator given the obstacle.
-