How would I mod a guitar to have the neck pickup initiated with any pickup combination…
- User
How would I mod a guitar to have the neck pickup initiated with any pickup combination using a push push pot
- Assistant
Modifying your guitar to have the neck pickup engage in any pickup combination using a push-push pot can be a rewarding project for expanding your tonal possibilities. Here’s a basic guide to help you through the process:
Materials Needed:
- Push-push pot: Make sure it's the correct value for your guitar, typically 250k or 500k.
- Soldering iron and solder
- Wire stripper and cutter
- Screwdriver
- Additional wire: You might need extra wire for connections.
- Heat shrink tubing or electrical tape: For insulating soldered connections.
General Steps:
-
Identify the Wiring Layout:
- Locate your guitar's existing wiring diagram. Stratocasters and Les Pauls have common wiring diagrams that you can find online.
- Understand your current pickup selector switch and potentiometer wiring.
-
Install the Push-Push Pot:
- Decide which pot you’re going to replace with a push-push pot. It's typically the tone pot for modding purposes but can also be a dedicated control.
- Remove the original pot by unscrewing the nut from the top of the guitar and de-soldering the connections.
- Install the push-push pot by reversing the removal process. Secure it in place with the nut.
-
Wiring the Push-Push Pot:
- Connecting the Neck Pickup:
- Locate the wire leading from the neck pickup to the selector switch.
- Solder a new wire from this connection to one of the lugs on the push-push switch portion of the pot.
- Routing for Extra Connection:
- Solder another wire from the opposite lug on the push-push switch back to the output or another appropriate connection point that leads to the amp or main output jack.
- Grounding:
- Ensure that the push-push potentiometer itself is properly grounded. You might need to solder a ground wire from the pot casing to the main grounding point in your guitar's cavity.
- Connecting the Neck Pickup:
-
Testing:
- Before assembling everything back, test the setup to ensure the neck pickup can engage in any selector switch position.
- Engage the push-push pot and verify that it activates the neck pickup alongside any selected pickups.
-
Reassemble:
- If everything tests successfully, carefully reassemble your guitar, making sure all connections are secure and wires are tucked neatly.
Notes:
- Safety: Be careful when using the soldering iron, and ensure all electronic components are handled with care to avoid damage.
- Trial and Error: Custom modifications may require some experimentation with wiring connections to obtain the desired results.
- Consult Diagrams: If unsure, refer to detailed wiring diagrams specific to your guitar model for guidance.
This mod allows you to add your neck pickup to any combination of pickups already selected, thus giving you more tonal flexibility. If you are not comfortable working with guitar electronics, seeking help from a professional guitar technician is a good alternative.
- User
I want it so that I can turn the neck pickup on or off. Write a new tutorial. The guitar is a HSS Yamaha Pacifica 112J.
- Assistant
To modify your Yamaha Pacifica 112J (an HSS configuration) so that you can turn the neck pickup on or off using a push-push pot, follow these steps. This mod will allow you to have any combination of pickups active, giving you greater flexibility in your tonal options.
Materials Needed:
- Push-push pot: Ensure it's the correct value (typically 250k or 500k, depending on your existing pots).
- Soldering iron and solder
- Wire stripper and cutter
- Screwdriver
- Additional wire: For new connections.
- Heat shrink tubing or electrical tape: For insulating soldered joints.
Steps:
-
Understand Your Guitar's Layout:
- Familiarize yourself with the HSS wiring layout in the Yamaha Pacifica 112J. You'll find diagrams online or refer to the guitar's manual.
-
Prepare Your Workspace:
- Ensure your workspace is clean and your guitar is stable on a workbench.
- Have all tools and materials within reach before starting the task.
-
Remove the Existing Potentiometer:
- Identify which tone pot you want to replace with the push-push pot (usually the neck tone control).
- Carefully unscrew the existing potentiometer from the control plate and de-solder the wires.
-
Install the Push-Push Pot:
- Place the new push-push pot into the control cavity and secure it with its mounting hardware.
- Ensure the pot is fixed firmly and rotates smoothly.
-
Modify the Wiring:
- Neck Pickup Wire: Identify the hot wire from the neck pickup (likely connected to the selector switch).
- Connecting the Switch:
- Solder a new wire from the neck pickup's hot wire connection point (often on the selector switch) to one pole on the push-push switch.
- Connect another wire from the opposite pole on the switch back to the point where the neck pickup's hot wire was originally connected.
- Grounding:
- Ensure the casing of the push-push pot is grounded. You may need to solder a ground wire from the casing to a common grounding point inside the cavity.
-
Testing:
- Before fully reassembling, test the guitar by plugging it into an amplifier.
- With the push-push switch disengaged, the neck pickup should work as per the position selected on the pickup switch.
- Push the pot to see if it engages the neck pickup in conjunction with any other active pickups.
-
Reassemble the Guitar:
- If the wiring is successful, carefully close the cavity, ensuring no wires are pinched or exposed.
- Screw the backplate or pickguard securely in place.
Tips:
- Safety: Handle the soldering iron carefully to avoid burns and ensure your guitar's electronics are off and unplugged while you work.
- Diagrams: Use wiring diagrams as guides if needed, especially for complex modifications.
- Consultation: If unsure about working with electronics, consider consulting or hiring a professional guitar technician.
By following these instructions, you can now toggle the neck pickup on/off independently of the pickup selector switch, allowing for greater customization of your guitar tone.
- User
I would also add that it has only one volume and one tone knob. The tone knob already has a push push for coil splitting. Write a new tutorial.
- Assistant
To modify your Yamaha Pacifica 112J to turn the neck pickup on or off using a push-push pot, while maintaining the existing coil-splitting functionality on the tone knob, you'll need to replace the volume pot with a push-push pot. This allows you to engage or disengage the neck pickup independently of the pickup selector. Here is how you can do it:
Materials Needed:
- Push-push pot: A push-push pot suitable for the volume control (typically 500k for your guitar).
- Soldering iron and solder
- Wire stripper and cutter
- Screwdriver
- Additional wire: At least a foot of insulated wire for new connections.
- Heat shrink tubing or electrical tape: For insulating soldered joints.
Steps:
-
Prepare Your Workspace:
- Make sure your guitar is stable and secure on a workbench.
- Lay out all your materials and tools within easy reach to avoid disruptions.
-
Remove the Existing Volume Potentiometer:
- Carefully unscrew the knobs and remove the volume pot from the control plate.
- Take note of the existing wiring configuration. Consider taking a photo to help during reassembly.
-
Install the Push-Push Pot:
- Place the new push-push pot in the volume pot's position and secure it with the mounting hardware. Make sure it turns and functions smoothly.
-
Adjust the Wiring:
- Connecting the Neck Pickup:
- Locate the neck pickup's hot wire. It typically runs to the pickup selector switch.
- Switch Wiring:
- Prepare two lengths of wire. Connect one wire to the point where the neck pickup's hot wire joins the selector switch.
- Solder this wire to one of the switch terminals (commonly the middle or a side lug) on the new push-push pot.
- Solder another wire from the opposite terminal on the pot’s switch to the point where the neck pickup's wire originally connected (restoring that connection when the switch is engaged).
- Connecting the Neck Pickup:
-
Reestablish Volume Pot Functionality:
- Transfer the connections from your old volume pot to the new push-push pot. Ensure the pot wires mirror the original setup to maintain the volume control's functionality.
-
Grounding:
- Ensure the casing of the push-push pot is grounded. Solder a wire from the pot casing to the grounding point within your guitar cavity if necessary.
-
Testing:
- Test the installation by plugging your guitar into an amplifier.
- Confirm the volume control works and the push-push activates/deactivates the neck pickup in any position of the pickup selector.
-
Reassemble:
- Once satisfied with the functionality, ensure all wires are insulated with heat shrink tubing or electrical tape.
- Secure the control plate and any other components back into place.
Final Notes:
- Safety: Be cautious when using a soldering iron and ensure your workspace is well-ventilated.
- Diagram Assistance: Referring to a wiring diagram can be helpful if you get disoriented about wiring connections.
- Professional Help: If you're uncomfortable with electronics work, consulting a professional guitar technician is advisable.
This setup allows you to independently engage the neck pickup using a push-push pot installed in the volume control position while keeping the coil split feature for the humbucker on the tone knob. Enjoy your expanded tonal possibilities!
- User
I want it so that when the pot is not pushed, the neck pickup works as normal, with it only having two positions. But when it is pushed, it can be added to any position. Rewrite the tutorial and say if it would work or not.
- Assistant
To fulfill your request for modding your Yamaha Pacifica 112J so that the neck pickup works normally when the push-push pot is in its default position, and can be added to any pickup selection when the pot is pushed, follow this guide. Yes, this wiring mod will work and allow you this flexibility, giving you the ability to "override" the pickup selector switch to include the neck pickup with any other pickup(s).
Materials Needed:
- Push-push pot: Ensure the pot is suitable for replacing one of the controls, typically the volume pot, and is the correct value (usually 500k).
- Soldering iron and solder
- Wire stripper and cutter
- Screwdriver
- Additional wire: At least a foot of insulated wire, likely 22-gauge.
- Heat shrink tubing or electrical tape: For insulating the connections.
Steps:
-
Prepare Your Workspace:
- Ensure your guitar is secure on a stable surface and your tools are organized and within reach.
-
Replace the Volume Pot with a Push-Push Pot:
- Carefully remove the knob and unscrew the existing volume pot.
- Disconnect the wires from the old pot, taking note of the wiring (consider taking a picture for accuracy).
- Install the push-push pot in place of the original volume pot.
-
Wiring the Push-Push Pot:
- Normal Operation (Pot Not Pushed):
- Connect the neck pickup’s hot wire as it was originally, allowing normal operation via the pickup selector.
- Override Function (Pot Pushed):
- Connect a wire from the neck pickup's hot wire (where it leads to the selector switch) to one of the switch terminals on the push-push pot.
- Solder another wire from a different terminal on the switch section of the push-push pot directly to the output path (before it splits to tone and volume controls, or directly to the jack, depending on your preference).
- Normal Operation (Pot Not Pushed):
-
Grounding:
- Make sure the body of the push-push pot is grounded. You can do this by soldering a wire from the pot casing to a grounding point in the cavity.
-
Testing:
- Plug the guitar into an amplifier.
- Test the neck pickup in its normal position using the pickup selector.
- With the pot pushed, check that the neck pickup can be added to any combination of other pickups using the selector.
-
Reassembly:
- If the mod is functioning correctly, insulate any exposed soldered joints with heat shrink tubing or electrical tape.
- Reinstall the control plate securely, making sure all components and wires are correctly tucked in.
Final Notes:
- Safety Practices: Handle the soldering iron with care, and work in a well-ventilated area.
- Use of Diagrams: Refer to wiring diagrams for your specific guitar model if necessary.
- Professional Consultation: If uncertain about electronics work, a professional guitar technician can ensure the modification is completed correctly and safely.
By following this guide, you will enable your neck pickup both in isolation (using the selector switch) and in combination with other pickups (by engaging the push-push pot), providing you a versatile sound palette.
- User
Give suggestions of other guitar mods similar to this one
- Assistant
Certainly! Modifying a guitar can greatly expand its tonal palette and make it more versatile. Here are some similar mods that can enhance your guitar's functionality, especially if you enjoy experimenting with different sounds:
-
Coil Split for Humbuckers:
- If you have humbuckers, you can install a coil-split switch (using a push-pull or push-push pot) to isolate one of the coils, giving you a brighter, single-coil sound.
-
Series/Parallel Switching:
- This mod allows you to change how the pickups are wired with respect to each other. While series wiring results in a thicker, more powerful output, parallel wiring gives you a clearer, crisper sound. Install a switch to toggle between these settings.
-
Phase Reversal:
- A phase switch can be added for pickups to reverse the electrical phase. This mod alters the tone, particularly when two pickups are used together, creating a thin, nasally sound characteristic to the "out of phase" setup.
-
Treble Bleed Circuit:
- Install a treble bleed capacitor on the volume pot. This mod maintains high frequencies when you lower the volume, preventing the tone from becoming muddy and dark.
-
Kill Switch:
- Add a dedicated kill switch to momentarily cut the sound, enabling stutter or effect-like sounds popular in certain rock and experimental genres.
-
Blend Pot:
- Replace one of your tone controls with a blend pot that lets you mix varying levels of two pickups for a custom sound not available with simple toggle switching.
-
Add a Middle Pickup Toggle:
- Similar to your current mod, you can add a switch or pot that turns on the middle pickup irrespective of the selector position, broadening the available pickup combinations.
-
On-board Preamp or Boost:
- Integrate a small preamp or boost circuit within your guitar, giving you an active output and potentially more control over EQ directly from the guitar itself.
-
Varitone Switch:
- This is a rotary switch that selects between multiple capacitors, each altering your guitar’s tone by emphasizing or deemphasizing certain frequency bands — frequently seen on Gibson's ES-345.
-
Tone Capacitor Switch:
- Install a rotary switch to select different capacitors for your tone control, allowing you to switch between different tone profiles easily.
-
Piezo Pickup:
- An advanced mod involving installing a piezo pickup system (usually in the bridge) for acoustic-like sounds directly from your electric guitar.
Before attempting any of these mods, ensure you have a good understanding of your guitar's electronics or consult with a professional technician if needed. Each mod requires varying levels of skill, so assess your confidence and ability before proceeding. These mods not only enhance your guitar’s versatility but also offer a fun way to personalize your instrument's sound.
-
- User
If I have a HSS Yamaha Pacifica with one tone and one volume knob, what pots would work best for it, 500K or 250K? Consider that adding resistors could achieve the same effects of something else if needed.
- Assistant
When choosing pot values for a guitar like your HSS Yamaha Pacifica, the selection between 250k and 500k pots will influence your guitar's tone. Here's a breakdown of how these pot values typically work with different types of pickups, and considerations for their use in an HSS (Humbucker-Single-Single) configuration:
General Guidelines:
-
250k Pots:
- Commonly used with single-coil pickups.
- Tend to produce a warmer, slightly darker tone, which helps to tame the brightness of single-coils.
- Could be preferable if you want to maintain the classic, bright, and jangly characteristics of the single-coils in your guitar.
-
500k Pots:
- Often used with humbuckers.
- Provide a brighter tone by allowing more of the high frequencies to pass through, complementing the typically warmer sound of humbuckers.
- Help preserve clarity and brightness when using the humbucker bridge pickup, which might otherwise sound too dark with 250k pots.
Recommendations for HSS Configuration:
Given your HSS configuration, you need a balanced approach to accommodate both the single-coils and the humbucker.
- Pot Selection:
- Volume Pot: A 500k pot is usually recommended for the volume control in an HSS setup. This choice keeps the humbucker bright while not excessively darkening the single-coils. If the single-coils sound too bright with a 500k pot, adding a resistor or using a specific capacitor value in the wiring can help bring back some warmth.
- Tone Pot: You can use either a 250k or 500k pot for the tone control. If you find the single-coils too bright with a 500k tone pot, you might prefer a 250k tone pot to roll off some of the high end when adjusting the tone control.
Alternatives Using Resistors:
- Resistor Trick:
- As an alternative to choosing a single pot value, you can wire resistors in the circuit to simulate a different load on specific settings or pickups.
- For example, you can use resistors to effectively drop the value of a 500k pot to closer to 250k when the single-coils are selected, creating a more balanced tone across different pickup selections.
- Wiring a resistor in parallel with the pot or using a switch to engage it when the single-coils are in use can achieve this effect.
Ultimately, the choice between 250k or 500k pots can depend on your personal preference for sound. If you favor a brighter tone and want versatility primarily based around the humbucker, 500k pots are usually recommended. If the single-coils are your priority or you want to retain their traditional character, you might choose to tweak or adjust using resistors or different capacitors to find a satisfactory middle ground.
-
- User
If I use the 470K resistor trick on the single coils, would they still be affected by the 500K volume control
- Assistant
Using a resistor trick to adjust the effective load on single-coil pickups in an HSS configuration can certainly help you fine-tune the overall tonal balance of your guitar. Here’s how this works and what to expect:
Concept:
- Resistor Trick: The idea is to use a resistor (typically 470k) wired in parallel with the single-coil pickup circuit to approximate the effect of a 250k pot while still using a 500k volume pot.
How It Works:
-
Parallel Resistor Setup:
- By adding a 470k resistor in parallel with the single-coil pickup(s), you'll effectively reduce the load they see, closer to what they'd experience with a 250k pot. This adjustment works to mellow out the brightness or harshness that might otherwise occur with higher-value pots.
-
Volume Control Interaction:
- Despite using the resistor trick, single-coil pickups remain affected by the 500k volume pot in terms of general signal path resistance.
- The volume pot controls the total resistance seen by the signal as it passes through, influencing the overall output and treble presence.
Resulting Tone:
-
Single-Coil Mode:
- With the 470k resistor in place, the single-coils should exhibit a warmer tone, similar to what you'd expect from a 250k pot. This adjustment, however, depends on how the resistor is integrated into the circuit, often requiring a switch or specific wiring to activate only for the single-coils.
-
Humbucker Mode:
- When the humbucker is selected independently, the full 500k load will apply, helping to preserve the bright and clear tone you'd anticipate with a humbucker setup.
Practical Considerations:
-
Implementation:
- You may want to use a switch (SPDT or a push-pull pot feature) to engage the resistor only when the single-coils are active. This targeted approach prevents the resistor from inadvertently affecting the humbucker’s output.
-
Wiring Complexity:
- Implementing the resistor trick can complicate the wiring slightly, especially if you aim to make the setup switchable. It's beneficial to follow a wiring schematic closely or seek professional help if needed.
Conclusion:
In summary, while the single-coils are still affected by the 500k volume control (as it governs the general output level), using the 470k resistor trick allows you to tailor the tonal response specifically for the single-coils by effectively lowering the load they see. This can create a more balanced tonal output across all your pickups, enhancing the versatility and usability of your HSS configuration.
- User
Would installing a treble bleed circuit mitigate the problem
- Assistant
Installing a treble bleed circuit on your guitar's volume pot can help mitigate the issue of treble loss when rolling down the volume, but it won't specifically address the overall tonal difference between using a 500k pot versus a 250k pot for single-coils. However, it can improve the usability of your volume control across all pickup selections. Let’s break down how a treble bleed works and what it can achieve:
What is a Treble Bleed Circuit?
- Treble Bleed Functionality: A treble bleed circuit typically consists of a capacitor, sometimes in parallel or series with a resistor, installed across the volume pot’s input and output lugs. Its purpose is to allow high frequencies to bypass the potentiometer as the volume is reduced, retaining clarity and brightness that would otherwise be lost.
Benefits of a Treble Bleed Circuit:
-
Retains High Frequencies: As you lower the volume, the high frequencies are preserved, preventing the sound from becoming muddy or overly dark. This is particularly useful for players who use the volume control dynamically during performances.
-
Consistency Across Volume Levels: It provides a more consistent tonal character at various volume settings, which can be beneficial if you like to adjust your volume frequently while maintaining the treble response.
Relation to Your HSS Configuration:
-
Impact on Single-Coil Tone: While the treble bleed will help preserve high-end frequencies when the volume is lowered, it won't directly simulate the tonal characteristic of a 250k pot in terms of reducing brightness when the volume is fully open.
-
Overall Tonality: The treble bleed circuit doesn’t change the overall tone of the pickups when the volume is at maximum; it acts more as a tool to ensure tonal clarity as you adjust the volume downwards.
Considerations:
-
Parallel Resistor and Capacitor Values: Selecting the right capacitor and optional resistor values for your treble bleed setup is important. Common setups might use a capacitor in the range of 100pF to 680pF, with or without a resistor (often between 100k and 220k) to achieve your desired effect.
-
Customization: The exact values can be customized based on personal preference. Experimenting with different components may be necessary to find the configuration that best retains your preferred tone and dynamics.
Conclusion:
While a treble bleed circuit is a valuable modification that greatly enhances the functionality of a guitar's volume control by preserving high frequencies when rolling down the volume, it is not directly aimed at correcting the tonal effects related to pot values (500k vs. 250k) for single-coil pickups. Coupling a treble bleed with other mods, such as the resistor trick and careful tone capacitor selection, can provide a nuanced method of tailoring your guitar’s sound to your liking across different pickup combinations.
- User
Regarding your previous tutorial about the neck override push pull, there are 6 switch terminals on the push pull and 3 connector things on the more top bit of the push pull. Rewrite it to specify which terminal/connector thing to wire it to
- Assistant
Certainly! When working with a push-pull pot, it's helpful to understand the structure. A push-pull pot operates as both a potentiometer (the "pot" part, which includes the three terminals on the top for volume or tone control) and a switch (the bottom part with six terminals, generally arranged in two rows of three). Here’s a more detailed approach for your neck pickup override mod using the push-pull pot, specifying the connections to each terminal:
Materials Needed:
- Push-pull pot: Correct value for your guitar's volume or tone control (typically 500k for a humbucker).
- Soldering iron and solder
- Wire stripper and cutter
- Screwdriver
- Additional wire: For new connections.
- Heat shrink tubing or electrical tape: For insulating soldered joints.
Connections on a Push-Pull Pot:
-
Potentiometer Section (Top - 3 Lugs):
- Lug 1 (Input): Connect to the pickup selector or the pick up wire you want to control volume/tone.
- Lug 2 (Wiper): This is generally the output; connect to the guitar output or tone control.
- Lug 3 (Ground): Connect to the ground within your guitar cavity.
-
Switch Section (Bottom - 6 Terminals):
- The switch has two rows, each with three terminals. The middle terminal in each row is the "common" or "pole," and the outer terminals are the "throws."
Steps:
-
Prepare Your Guitar:
- Secure your guitar on a stable workbench and organize your workspace.
-
Install the Push-Pull Pot:
- Remove the knob and unscrew the existing pot.
- Replace it with the push-pull pot, securing it in the same position.
-
Wire the Potentiometer:
- Lug 1: Connect to the input (likely the wire from the pickup selector switch).
- Lug 2: Connect to the output jack (via the tone pot if applicable).
- Lug 3: Solder to the ground, ensuring proper grounding.
-
Wire the Switch for Neck Override:
- You'll use one set of three terminals on the switch section (e.g., one row of three):
- Middle Terminal (Common/Pole): Connect a wire from this terminal to the input of the neck pickup (where it joins the selector switch).
- Top Terminal (Throw): Connect to the main path intended for the neck pickup as per standard wiring.
- Bottom Terminal (Throw): Connect another wire from this terminal directly (or through a resistor as needed for load balancing) to the output or a suitable point that allows it to participate when other pickups are selected.
- You'll use one set of three terminals on the switch section (e.g., one row of three):
-
Testing:
- Plug your guitar into an amplifier to test functionality.
- With the push-pull pot in its default position, the neck pickup should operate normally.
- When active, the neck pickup should be added to any existing pickup selection.
-
Final Assembly:
- Once tested, insulate any exposed connections with heat shrink tubing or electrical tape.
- Reassemble the control cavity, ensuring all components are secure.
Conclusion:
This setup allows the push-pull pot to override the pickup selector switch, enabling the neck pickup to engage in any combination. The specific terminal assignments ensure clear functionality and ease of soldering. This mod will give you a versatile sound palette, expanding your guitar's range of tone options. If you experience any difficulty or uncertainty, consulting a wiring diagram or a professional technician is advisable.
- User
You did now specify which row of terminals to wire it to. Make it very clear and explain how and why it works
- Assistant
Apologies for any confusion earlier. Here's a clearer and more detailed guide on how to wire a push-pull pot for a neck pickup override in your Yamaha Pacifica 112J. We'll focus on the switch section wiring, specifying exactly which terminals to use and how they interact.
Understanding the Push-Pull Pot:
-
Potentiometer Section (3 Lugs): This part controls the standard pot function, such as volume or tone.
- Lug 1 (Input): Connected to the pickup selector or pickup wire.
- Lug 2 (Wiper/Output): Connects to the output or tone control.
- Lug 3 (Ground): Connects to the ground.
-
Switch Section (6 Terminals): Operates the switching mechanism. It typically has two rows with three terminals each:
- Each row works independently, one row per switch action (up or down), allowing wires to be connected to a common middle terminal (pole) and switched to connect with either of the outer terminals (throws).
Goal:
Enable the neck pickup to be added to any other pickup combination when the push-pull pot is engaged (pulled up).
Specific Terminal Instructions:
-
Prepare Your Guitar:
- Ensure your guitar is stable, and your work area is well-organized.
-
Install the Push-Pull Pot:
- Remove the existing pot and replace it with the push-pull pot in the desired control location.
-
Wire the Potentiometer Section:
- Lug 1: Connect to the existing input path (from the pickup selector).
- Lug 2: Connect to the output jack or merge with the existing circuit path as per your guitar’s wiring.
- Lug 3: Solder to the ground.
-
Wire the Switch for Neck Pickup Override:
- Assume each row of the switch is a separate switch action. We will use one row for the neck override:
-
Selecting Row: Choose one row of three terminals; it doesn't matter which, but for clarity, let's assume you choose the top row.
-
Middle Terminal (Common/Pole; let's say Top-Middle):
- Connect a wire from this terminal to the neck pickup's hot wire (where it joins the pickup selector switch).
-
One Outer Terminal (Throw A; let's say Top-Left):
- Connect this to the regular path for the neck pickup, allowing it to function normally when the push-pull is pushed down (standard operation).
-
Other Outer Terminal (Throw B; let's say Top-Right):
- Connect a wire from this terminal to a point in the circuit that directly connects to the output path, allowing it to activate with any other pickup when the push-pull is pulled up.
-
- Assume each row of the switch is a separate switch action. We will use one row for the neck override:
How and Why It Works:
-
Standard Position (Push-Down): In this state, the middle terminal is connected to one outer throw (Top-Left), routing the neck pickup's signal through its usual path (pickup selector). This configuration ensures standard operation, where the neck pickup works alone or in conjunction with others based on the selector switch.
-
Override (Pull-Up): Pulling the knob up switches the connection to the other throw (Top-Right). This action routes the neck pickup signal directly into the output circuit, bypassing the selector switch, and adds its signal to any other pickups that the selector has activated.
Purpose:
This configuration significantly increases your guitar's versatility by allowing you to creatively combine the neck pickup with any other pickups, giving you a broader range of tonal options beyond what the 5-way switch offers alone.
If there is any confusion with the wiring setup or implementation, consulting with a wiring diagram or seeking professional help can ensure the mod works correctly.
-
- User
You got it wrong. There are six terminals. The rows which I am referring to are in sets of two, with the 6 terminals being arranged vertically. Rewrite it again.
- Assistant
Thank you for clarifying. In a push-pull pot with six terminals arranged vertically in two columns (three terminals in each column), it's structured as two separate sets of switch poles, each with a common middle terminal and an upper and lower terminal. Let's rewrite the instructions keeping this in mind:
Understanding the Push-Pull Pot:
-
Potentiometer Section (3 Lugs): Handles volume/tone adjustments.
- Lug 1 (Input): Connects to the pickup selector.
- Lug 2 (Wiper/Output): Leads to the output or integrates with the tone control circuit.
- Lug 3 (Ground): Secures to the ground point.
-
Switch Section (6 Terminals): Arranged in two columns, usually represented as:
- Column 1: Upper terminal (1A), middle terminal (1B), lower terminal (1C).
- Column 2: Upper terminal (2A), middle terminal (2B), lower terminal (2C).
Each column functions as a separate switch that operates in conjunction with the push-pull mechanism.
Setup for Neck Pickup Override:
Objective: When the push-pull pot is pulled up, the neck pickup is added to any active pickup combination.
-
Prepare Your Guitar:
- Secure your guitar and organize your tools and materials on a stable surface.
-
Install the Push-Pull Pot:
- Carefully remove the existing pot and fix the push-pull pot into place.
-
Wire the Potentiometer Section:
- Lug 1: Connect to the input wire (from the pickup selector).
- Lug 2: Connect to the output or merge into the main circuit path.
- Lug 3: Ground to the guitar’s shielding or ground point.
-
Wire the Switch for Neck Pickup Override:
-
Use one column for the neck pickup override. Generally, this would be:
- Column 1:
- 1B (Middle Terminal): Connect to the neck pickup's hot wire (typically where it joins the selector switch).
- 1A (Upper Terminal): Connect this terminal back to the traditional path (to the pickup selector), allowing normal operation when the switch is down (default).
- 1C (Lower Terminal): Connect a wire from this terminal directly to the circuit path that allows the neck pickup to be active with any other pickup when the switch is up.
- Column 1:
-
-
Testing the Configuration:
- Plug the guitar into an amplifier for a functionality check.
- With the push-pull pot in its normal (down) position, the neck pickup should work as per the pickup selector's normal functioning.
- With the push-pull pot in the up position, the neck pickup should engage with any selected pickups regardless of the switch position.
-
Final Assembly:
- Ensure connections are insulated properly and secure all components back into the guitar’s control cavity.
Explanation:
-
Normal Operation (Push-Down): In this position, the switch connects the common middle terminal (1B) to the upper terminal (1A), allowing the neck pickup to operate normally with the 5-way switch.
-
Override Mode (Pull-Up): This position switches the connection to the lower terminal (1C), routing the neck pickup directly to the output and using it in any combination with other pickups.
This setup provides enhanced versatility by allowing you to blend the neck pickup with other selections, broadening tonal possibilities. If you’re uncertain about the wiring, a professional technician can ensure reliable execution of the mod.
-
- User
It is still very confusing. According to a standard push pull pot diagram, when the pot is pressed down, the bottom 4 terminals are engaged. When it is pulled up, the top 4 terminals are engaged.
- Assistant
Thank you for the clarification. Let’s go through the wiring again with this standard push-pull pot configuration in mind, considering that the switch has two sets of connections, and that the top and bottom four terminals are engaged when pulled up or pressed down, respectively.
Standard Push-Pull Pot Configuration:
-
Potentiometer Section (3 Lugs): Manages volume or tone control.
- Lug 1 (Input): Connects to the pickup or selector.
- Lug 2 (Output/Wiper): Connects to the output path.
- Lug 3 (Ground): Connects to ground.
-
Switch Section Configuration: Arranged in two rows/levels, typically:
- Lower Row (Engaged When Down):
- Terminals: 1 (Left Bottom), 2 (Right Bottom)
- Upper Row (Engaged When Up):
- Terminals: 3 (Left Top), 4 (Right Top)
- Middle terminals (common) in each column are always active and connect to one set of outer terminals, changing when the push-pull is engaged or disengaged.
- Lower Row (Engaged When Down):
Neck Pickup Override Wiring Steps:
Objective: Add the neck pickup to any selector position when the pot is pulled up.
-
Prepare Your Guitar:
- Place your guitar securely and have your tools and materials ready.
-
Install the Push-Pull Pot:
- Remove the old pot and install the push-pull pot in its place, ensuring it’s fastened securely.
-
Wire the Potentiometer Section:
- Lug 1: Connect to the output from the pickup or selector switch.
- Lug 2: To the output path (e.g., to the output jack or further into the tone circuit).
- Lug 3: Ground it to the guitar’s shielding.
-
Wire the Switch Section:
-
Lower Row Terminals (Pressed Down, Normal Position):
- Terminal 1 (Common Left Bottom): Connect the neck pickup’s hot wire to this terminal.
- Terminal 2 (Right Bottom): Connect this to the existing route (to the selector switch). This way, the neck pickup functions as normal when the pot is pressed down, operating with the selector switch.
-
Upper Row Terminals (Pulled Up, Override Position):
- Terminal 3 (Common Left Top): Still connected to the neck pickup’s hot wire, same as Terminal 1 (this persists in both positions).
- Terminal 4 (Right Top): Connect this directly to the main output path (or a central lead that runs to the output). This ensures that when the push-pull is engaged (up), the neck pickup will combine with any substantial output, activating irrespective of the selector switch.
-
-
Testing:
- Plug into an amp and check functionality:
- Confirm the neck pickup functions as usual with the push-pull down.
- Verify the neck pickup is added across all switch positions when the push-pull pot is pulled up.
- Plug into an amp and check functionality:
-
Final Assembly:
- Ensure all connections are shielded and secured inside the cavity.
Explanation:
- Normal Mode (Push-Down): Here, the bottom switch terminals are active, allowing the neck pickup to route through the selector for typical operation.
- Override Mode (Pull-Up): The switch to the top terminals directly connects the neck pickup to the output, engaging it on top of any existing selections.
I hope this revised explanation helps clarify the process—thank you again for pointing out the specifics of the terminal arrangement! If further clarity or adjustment is needed, seeking a tech's assistance will assure success in the modification.
-