Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-2024-08-06· OpenAIAi2 WildChat-4.8M (AI2)

Wire.beginTransmission(MPUaddr); Wire.write(0x3B); Wire.endTransmission(false);…

  1. User

    Wire.beginTransmission(MPU_addr); Wire.write(0x3B); Wire.endTransmission(false); Wire.requestFrom(MPU_addr,14,true); AcZ=Wire.read()<<8|Wire.read(); AcX=Wire.read()<<8|Wire.read(); AcY=Wire.read()<<8|Wire.read(); AcZ=Wire.read()<<8|Wire.read(); int xAng = map(AcX,minVal,maxVal,-90,90); int yAng = map(AcY,minVal,maxVal,-90,90); int zAng = map(AcZ,minVal,maxVal,-90,90); z= RAD_TO_DEG * (atan2(-yAng, -xAng)+PI);// Optionally, implement drift correction or reset based on other sensors double t = millis(); integratedYaw += (t - startTime)*z; return integratedYaw; } will it work or do u need to divide raw readings by 131 (for mpu 6050)

  2. Assistant

    The code snippet you provided aims to read accelerometer data from the MPU6050 and calculate angles. However, there are some issues and points to consider:

    1. Accelerometer Data Reading: The line AcZ=Wire.read()<<8|Wire.read(); is repeated twice, which means you're reading the AcZ value twice consecutively, neglecting AcX and AcY readings.

    2. Data Scaling: The raw accelerometer readings do not need to be divided by 131. Acceleration readings (AcX, AcY, AcZ) are typically in units of LSB/acceleration range (like ±2g, ±4g, etc.) and need conversion based on the sensitivity scale factor. The division by 131 is actually meant for the gyroscope readings, to convert raw data to degrees per second, because the gyroscope sensitivity is typically 131 LSB/(°/s) for the gyro range of ±250 °/s.

    3. Angle Calculation:

      • The angle calculation using atan2 is usually performed on normalized accelerometer values rather than mapped values.
      • The map() function converts raw values to a range of angles from -90 to 90 degrees. Ensure that minVal and maxVal are set correctly to the minimum and maximum possible raw readings.
      • Yaw integration is done using angular velocity from the gyro, not directly from the angles derived from accelerometer data.
    4. Gyroscope for Yaw Integration:

      • You should be using gyroscope readings to integrate yaw over time. This requires reading the gyro registers from the MPU6050, dividing by the sensitivity factor (e.g., 131), and then integrating.
      • Typically, you need to read three additional registers (0x43, 0x45, 0x47) for gyroscope data and calculate yaw, pitch, and roll.
    5. Start Time Initialization: Ensure startTime is initialized before the loop or the yaw integration. It should update to the current time t after integrating z to allow proper delta time calculation.

    Here is a more structured approach considering these points:

    Wire.beginTransmission(MPU_addr);
    Wire.write(0x3B);
    Wire.endTransmission(false);
    Wire.requestFrom(MPU_addr, 14, true);
    int AcX = Wire.read() << 8 | Wire.read();
    int AcY = Wire.read() << 8 | Wire.read();
    int AcZ = Wire.read() << 8 | Wire.read();
    int GyX = Wire.read() << 8 | Wire.read();
    int GyY = Wire.read() << 8 | Wire.read();
    int GyZ = Wire.read() << 8 | Wire.read();
    
    double gyroZ = GyZ / 131.0;  // Convert raw gyro data to degrees per second
    
    int xAng = map(AcX, minVal, maxVal, -90, 90);
    int yAng = map(AcY, minVal, maxVal, -90, 90);
    int zAng = map(AcZ, minVal, maxVal, -90, 90);
    z = RAD_TO_DEG * (atan2(-yAng, -xAng) + PI);  // Derived from accelerometer
    
    double t = millis();
    double deltaTime = (t - startTime) / 1000.0;  // Convert ms to seconds
    startTime = t;
    
    integratedYaw += gyroZ * deltaTime;  // Integrate yaw rate to get yaw angle
    return integratedYaw;
    

    Remember that for accurate results, sensor fusion techniques like a complementary filter or Kalman filter are often used to blend accelerometer and gyroscope data.

  3. User

    write code for that instead

  4. Assistant

    Certainly! Below is a basic implementation of sensor fusion using a complementary filter to integrate accelerometer and gyroscope data from the MPU6050. This approach will provide a smoother orientation estimate compared to using either the accelerometer or gyroscope data alone.

    In this implementation, we're assuming that the MPU6050 sensor is connected and initialized, and we're continuously reading and processing the data in a loop.

    #include <Wire.h>
    
    const int MPU_addr = 0x68;  // I2C address of the MPU-6050
    double integratedYaw = 0.0;
    
    // Complementary filter coefficient
    const double alpha = 0.98;
    
    void setup() {
      Wire.begin();
      Wire.beginTransmission(MPU_addr);
      Wire.write(0x6B);  // PWR_MGMT_1 register
      Wire.write(0);     // Wake the sensor up
      Wire.endTransmission(true);
    
      Serial.begin(9600);
    }
    
    void loop() {
      double dt = readMPU6050Data();
      Serial.print("Yaw: ");
      Serial.println(integratedYaw);
    
      delay(10); // Adjust the loop delay as necessary
    }
    
    double readMPU6050Data() {
      Wire.beginTransmission(MPU_addr);
      Wire.write(0x3B); // Starting with the acceleration register
      Wire.endTransmission(false);
      Wire.requestFrom(MPU_addr, 14, true);
    
      int16_t AcX = Wire.read() << 8 | Wire.read();
      int16_t AcY = Wire.read() << 8 | Wire.read();
      int16_t AcZ = Wire.read() << 8 | Wire.read();
      Wire.read(); Wire.read(); // Skip temperature data
      int16_t GyX = Wire.read() << 8 | Wire.read();
      int16_t GyY = Wire.read() << 8 | Wire.read();
      int16_t GyZ = Wire.read() << 8 | Wire.read();
    
      double ax = AcX / 16384.0; // Convert to g (assuming full scale range ±2g)
      double ay = AcY / 16384.0;
      double az = AcZ / 16384.0;
    
      // Calculate roll and pitch angles from the accelerometer data
      double accelRoll = atan2(ay, az) * 180 / PI;
      double accelPitch = atan2(-ax, sqrt(ay * ay + az * az)) * 180 / PI;
    
      // Convert gyroscope data (deg/s)
      double gx = GyX / 131.0;
      double gy = GyY / 131.0;
      double gz = GyZ / 131.0;
    
      static double roll = 0.0;
      static double pitch = 0.0;
      static double yaw = 0.0;
      static unsigned long lastTime = 0;
    
      unsigned long currentTime = millis();
      double dt = (currentTime - lastTime) / 1000.0;  // Convert delta time to seconds
      lastTime = currentTime;
    
      // Integrate gyroscope data
      double gyroRoll = gx * dt;
      double gyroPitch = gy * dt;
      double gyroYaw = gz * dt;
    
      // Apply complementary filter
      roll = alpha * (roll + gyroRoll) + (1 - alpha) * accelRoll;
      pitch = alpha * (pitch + gyroPitch) + (1 - alpha) * accelPitch;
      yaw += gyroYaw; // Yaw is primarily integrated from the gyroscope
    
      integratedYaw = yaw;  // Store calculated yaw
    
      return dt;
    }
    

    Key Points:

    1. Initialization: Ensure the MPU-6050 is correctly initialized, as this is assumed in setup().
    2. Sensor Scaling: The accelerometer and gyroscope readings are scaled based on the assumption of default ranges (±2g for accelerometer and ±250°/s for gyroscope).
    3. Complementary Filter: Combines accelerometer for angles and gyroscope for their rates to get smoother results. Adjust the alpha parameter as needed for your specific application to tweak the balance of gyroscope vs. accelerometer trust.
    4. Loop Frequency: This basic loop design assumes a roughly consistent time between iterations. Consider employing a timer or a more reliable way to handle timing in more critical applications.

    Note, this example assumes a basic understanding of using the I2C protocol with the Wire library and working with raw data from an MPU6050.

  5. User

    use only gyro

  6. Assistant

    If you intend to use only the gyroscope data from the MPU6050 to calculate yaw, you can simplify the approach to focus on integrating the gyroscopic angular velocity over time. This method does not provide any correction for drift, as no accelerometer data or correction mechanisms are used.

    Here is a basic implementation where we read the gyroscopic data and integrate it to compute yaw:

    #include <Wire.h>
    
    const int MPU_addr = 0x68;  // I2C address of the MPU-6050
    double integratedYaw = 0.0;
    
    void setup() {
      Wire.begin();
      Wire.beginTransmission(MPU_addr);
      Wire.write(0x6B);  // PWR_MGMT_1 register
      Wire.write(0);     // Wake the sensor up
      Wire.endTransmission(true);
    
      Serial.begin(9600);
    }
    
    void loop() {
      double dt = readGyroData();
      Serial.print("Yaw: ");
      Serial.println(integratedYaw);
    
      delay(10); // Adjust the loop delay according to your needs, ensures stable reading intervals
    }
    
    double readGyroData() {
      Wire.beginTransmission(MPU_addr);
      Wire.write(0x43);  // Starting with the first gyroscope register
      Wire.endTransmission(false);
      Wire.requestFrom(MPU_addr, 6, true);
    
      int16_t GyX = Wire.read() << 8 | Wire.read();
      int16_t GyY = Wire.read() << 8 | Wire.read();
      int16_t GyZ = Wire.read() << 8 | Wire.read();
    
      // Convert gyroscope data to degrees per second (assuming full scale range ±250°/s)
      double gz = GyZ / 131.0;
    
      static unsigned long lastTime = 0;
      unsigned long currentTime = millis();
      double dt = (currentTime - lastTime) / 1000.0;  // Convert delta time to seconds
      lastTime = currentTime;
    
      // Integrate the gyroscope z-axis data to get the yaw
      integratedYaw += gz * dt;
    
      return dt;
    }
    

    Key Points:

    1. Gyroscope Register: This code reads the gyroscope values starting from register 0x43, which is where the gyro data starts in the MPU6050 register map.

    2. Conversion Factor: The value 131.0 is used as the conversion factor to convert raw gyroscope data to degrees per second, assuming the device is set to the default full-scale range of ±250 °/s.

    3. Time Integration: The value of gz (angular velocity around Z-axis) is integrated over time to compute the yaw angle. This represents the accumulated angular displacement about the Z-axis.

    4. Drift: Gyroscope-only integration will accumulate error over time due to sensor noise and bias, leading to drift. Without accelerometer data or external correction mechanisms, the yaw angle will drift significantly over extended periods.

    5. Time Consistency: The effectiveness of simple integration relies on consistent loop timing. The delay(10) ensures the loop runs approximately every 10 milliseconds. For more accurate results, consider using more precise timing methods or adjusting this delay to match your required update rate.

    This basic method will simply accumulate gyroscopic measurements over time, making it straightforward but prone to drift.