Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-2024-08-06· OpenAIAi2 WildChat-4.8M (AI2)

On OpenBSD i'm trying to redirect or forward trafic from local subnet 192.168.10.0/24 to…

  1. User

    On OpenBSD i'm trying to redirect or forward trafic from local subnet 192.168.10.0/24 to the default gateway, because for some reasons it's not flowing after initiating OpenIKED IPSEC tunnel. How am i suppose to redirect this trafic via pf or whta ?

  2. Assistant

    On OpenBSD, if you're having trouble routing traffic from a local subnet (e.g., 192.168.10.0/24) to a default gateway after initiating an OpenIKED IPsec tunnel, you can use pf (Packet Filter) to handle this. Usually, the issue might arise due to routing conflicts or missing routes once the IPsec tunnel is up. Here are some steps you can take to redirect or forward the traffic properly:

    1. Check Routing Table First, ensure that the routing table still has a valid/default route pointing to your actual network gateway aside from any IPsec-related routes. You can view the current routing table using:

      netstat -rn
      
    2. Modify PF Rules If the routing table looks correct, you might want to redirect traffic using pf. Here’s a step-by-step guide:

      • Open your PF configuration file, usually located at /etc/pf.conf.

      • Ensure your external interface (let's assume it's called em0) and your internal interface (em1) are correctly defined in your rules.

      • Add or modify rules to ensure that the internal traffic is correctly passed to your external interface or file as per your network setup. Here's a basic example:

        # Define interfaces
        ext_if = "em0"
        int_if = "em1"
        local_net = "192.168.10.0/24"
        
        # Normalization (optional)
        scrub in all
        
        # NAT for outbound traffic from the local network
        match out on $ext_if from $local_net to any nat-to ($ext_if)
        
        # Pass traffic
        block in all
        pass out on $ext_if from $local_net to any
        pass in on $int_if from $local_net
        
      • Make sure there’s a NAT rule if your traffic needs to go out to the Internet.

      • Reload the PF configuration:

        pfctl -f /etc/pf.conf
        pfctl -e  # Enable pf if it's not already enabled
        
    3. IPsec Considerations

      • Ensure your IPsec policies allow traffic to flow correctly from the source to the destination network.
      • Verify your IPsec configuration to see if any policy might be overriding your expected traffic flow.
    4. Test and Debug

      • After these changes, test the connectivity to ensure that traffic flows as expected.
      • Use tcpdump to trace packet flow and ensure rules are working:
        tcpdump -i em0
        tcpdump -i em1
        
    5. Log and Monitor

      • If issues persist, enable logging for pf rules to gather more information and diagnose the root cause of the problem.
    6. Advanced Steps

      • If necessary, adjust IP forwarding settings or make use of additional OpenBSD capabilities such as route-to or reply-to directives in pf for more complex routing scenarios.

    Remember always to backup your existing configurations before making any changes, allowing you to revert to a known working state if necessary.

  3. User

    how to properly configure OpenIKED then to have propper IPSEC SA for this local subnet , which is on the another interface ure0 ?? Apparently this is that is missing. Even if i route traffic -- it is not founding its route probably due to SA missing

  4. Assistant

    To properly configure OpenIKED on OpenBSD and ensure that there is an appropriate IPsec Security Association (SA) for your local subnet (192.168.10.0/24) on the ure0 interface, you'll need to make sure your iked.conf file is correctly set up. Here are the steps you should follow:

    1. Configure OpenIKED (/etc/iked.conf)

      You'll want to define a policy for the IPsec connection that includes the local subnet (192.168.10.0/24). Here's an example configuration snippet that might help as a baseline:

      # Define interfaces and networks
      local_if = "ure0"
      local_net = "192.168.10.0/24"
      
      # Replace this with the IP of the remote peer
      remote_peer = "remote.peer.ip.address"
      
      ikev2 "ipsec-tunnel" {
          # Specify local and remote auth parameters. Adjust the authentication
          # method as per your needs, e.g., certificates or preshared keys.
          
          local id "/CN=your-certificate-common-name"
          remote id "/CN=remote-peer-certificate-common-name"
      
          # Preshared keys can be defined if not using certificates
          # psk "your-pre-shared-key"
      
          # Specify networks
          from $local_net to $remote_peer
          to $remote_peer any
      
          # Define proposals (algorithms) - adjust according to your requirements
          proposal aes256-sha256-modp2048
          
          # Also consider specifying a lifetime, key exchange protocols, etc.
      }
      
    2. Ensure Policies are Loaded

      Once you configure /etc/iked.conf, ensure the daemon is running and the configuration is loaded:

      rcctl enable iked
      rcctl start iked
      
      # Check status and ensure it's running without errors
      ikectl show sa
      
    3. Check Debug Information

      If the SA does not appear as expected or traffic is not flowing, enable logging to get detailed diagnostics:

      iked -dv
      

      This will provide verbose output and could indicate where things are going wrong.

    4. Verify IPsec SA and Route Policies

      • Use ipsecctl or check with ifconfig and route commands to ensure that correct SAs and routes are in place.
      ipsecctl -s all
      
      • The output should list Security Associations (SAs) relevant to 192.168.10.0/24 subnet.
    5. Testing and Troubleshooting

      • Ensure that there's adequate network access between your local host or subnet and the IPsec tunnel endpoint.
      • Use ping or traceroute to test connectivity.
      • Adjust firewall or routing configurations if necessary — ensure pf rules are not dropping traffic or interfering with the desired path.
    6. Verify Network Configuration

      Double-check that your ure0 interface has the correct address configuration and subnet settings. Use:

      ifconfig ure0
      

    By ensuring these configurations and checks are in place, you should be able to establish and troubleshoot the IPsec tunnel, allowing traffic from the 192.168.10.0/24 subnet to reach its intended destination through the tunnel. Remember to always adjust settings according to your specific network and security requirements.

  5. User

    How can i use StrongSwan instead to connect to the remotely running OpenIKED daemon with cert and routing all trafic through this IPSEC tunnel ?

  6. Assistant

    To use StrongSwan to connect to a remote system running OpenIKED and route all traffic through the IPsec tunnel, you'll need to set up StrongSwan on your client and configure it to work with OpenIKED using certificates for authentication. Here’s a step-by-step guide to configuring StrongSwan in this scenario:

    Prerequisites

    1. Certificates:

      • Ensure you have a valid certificate for the StrongSwan client and access to the OpenIKED server's CA certificate.
      • Usually, you’ll have a client certificate and private key (often in .crt and .key files) along with the CA certificate (ca.crt).
    2. Networking:

      • Make sure your network allows traffic over the appropriate ports (typically UDP 500 and 4500 for IKE/IPsec).

    StrongSwan Configuration

    1. Install StrongSwan

    If you haven't already installed StrongSwan, you can do so:

    # On Debian-based systems
    sudo apt-get update
    sudo apt-get install strongswan
    
    # On Red Hat-based systems
    sudo yum install strongswan
    

    2. Configure IPsec with StrongSwan

    Edit the StrongSwan configuration file, usually located at /etc/ipsec.conf, to define your connection profile. You might want to set it up like this:

    conn ikev2-iked
        keyexchange=ikev2
        dpdaction=clear
        dpddelay=300s
        eap_identity=%identity
    
        # Local and remote IDs
        leftcert=client.crt
        leftid="your-client-id"  # For example, the Common Name (CN) in your certificate
        leftsourceip=%config
    
        right=remote.iked.host  # IP or hostname of the OpenIKED server
        rightid="remote.server.id"  # The ID of the server, often its CN
    
        rightsubnet=0.0.0.0/0    # Tunnel all traffic
        authby=pubkey
        auto=start
    

    3. Supply Credentials

    Place your client certificate and key in /etc/ipsec.d/certs and /etc/ipsec.d/private, respectively, and ensure the server’s CA certificate is in /etc/ipsec.d/cacerts.

    Example file placements:

    • /etc/ipsec.d/certs/client.crt
    • /etc/ipsec.d/private/client.key
    • /etc/ipsec.d/cacerts/ca.crt

    4. Configure IPsec Secrets

    Create or modify /etc/ipsec.secrets to include your private key:

    : RSA client.key
    

    5. Start and Test Connection

    Start the StrongSwan service:

    sudo systemctl start strongswan
    sudo systemctl enable strongswan
    

    Check the status and logs to ensure the connection is established:

    sudo ipsec statusall
    sudo journalctl -u strongswan
    

    Additional Configuration

    • Routing and DNS:

      • To route all traffic through the VPN, ensure that the rightsubnet is configured as 0.0.0.0/0.
      • You may also want to update DNS settings or use leftdns to specify DNS servers.
    • Firewall:

      • Ensure necessary ports (IKEv2: UDP 500/4500) are open on your client’s firewall and any intermediate firewalls/routers.
    • Troubleshooting:

      • If you encounter issues, enable more verbose logging by adjusting the charondebug setting in /etc/strongswan.d/charon.conf.
      • Use tcpdump to analyze traffic between your client and the OpenIKED server for additional troubleshooting.

    This setup should allow your StrongSwan client to establish an IPsec connection to an OpenIKED server, using certificates for authentication, and route all traffic through the IPsec tunnel. Adjust configurations according to your specific network and authentication needs.

  7. User

    what is this -> " Create or modify /etc/ipsec.secrets to include your private key:" where to get this from? should it match with remote OpenIKED ?

  8. Assistant

    The /etc/ipsec.secrets file in StrongSwan contains sensitive information used during the authentication process, specifically private keys and sometimes other credentials like pre-shared keys (PSKs). Here's a more detailed explanation and guidance on how to prepare this file:

    Understanding /etc/ipsec.secrets

    1. Purpose: The file provides StrongSwan with the necessary cryptographic material (e.g., private keys) to establish a secure connection with a remote peer.

    2. Content for Certificate-Based Authentication:

      • When using certificate-based authentication, /etc/ipsec.secrets typically contains a reference to your private key file associated with your client certificate.

    Steps to Prepare /etc/ipsec.secrets

    1. Obtain Your Private Key and Certificate:

      • Private Key: This is usually generated during the creation of your client certificate, often stored as a .key file. It’s essential to keep this file secure and private.
      • Client Certificate: The corresponding public certificate, usually in a .crt file. It was issued by a Certificate Authority (CA) that the OpenIKED server trusts.
    2. Create or Modify /etc/ipsec.secrets:

      • Typically, you reference your private key in ipsec.secrets. Here’s an example if your private key is stored in /etc/ipsec.d/private/client.key:

        : RSA /etc/ipsec.d/private/client.key
        
    3. Does it Need to Match the Remote OpenIKED?

      • No Direct Match: The private key should not be shared with the remote OpenIKED. It should stay confidential on your StrongSwan client device.
      • Common Trust: Both the StrongSwan client and the OpenIKED server must trust the same CA that issued their respective certificates, facilitating mutual authentication.

    Common Errors and Troubleshooting

    • Key Mismatch: Ensure that the private key corresponds to your public certificate.
    • Permissions: The private key should have appropriate file permissions—only accessible to the root user (e.g., 600).
    • Path Accuracy: Double-check all paths in your configuration files to make sure they point to the correct files.
    • Logs: Check logs if issues arise. For StrongSwan, you can often use:
      sudo journalctl -u strongswan
      

    Summary

    When setting up StrongSwan for certificate-based authentication, ensure you have the correct client certificate and private key files, configure /etc/ipsec.secrets to point to your private key file, and verify that both the client and server trust the same CA. This setup ensures secure and authenticated communication with your OpenIKED server.