#include <xc.h> #include <stdint.h> #define XTALFREQ 16000000 // 16 MHz oscillator…
- User
#include <xc.h> #include <stdint.h>
#define _XTAL_FREQ 16000000 // 16 MHz oscillator frequency
#define SINE_TABLE_SIZE 256
// Sine table with values from 0 to 1023 for 10-bit PWM const uint16_t sine_table[SINE_TABLE_SIZE] = {384, 393, 403, 412, 422, 431, 440, 450, 459, 468, 477, 486, 495, 504, 513, 522, 531, 540, 548, 557, 565, 573, 581, 589, 597, 605, 613, 620, 628, 635, 642, 649, 656, 662, 669, 675, 681, 687, 692, 698, 703, 708, 713, 718, 723, 727, 731, 735, 739, 742, 746, 749, 751, 754, 756, 759, 761, 762, 764, 765, 766, 767, 768, 768, 768, 768, 768, 767, 766, 765, 764, 762, 761, 759, 756, 754, 751, 749, 746, 742, 739, 735, 731, 727, 723, 718, 713, 708, 703, 698, 692, 687, 681, 675, 669, 662, 656, 649, 642, 635, 628, 620, 613, 605, 597, 589, 581, 573, 565, 557, 548, 540, 531, 522, 513, 504, 495, 486, 477, 468, 459, 450, 440, 431, 422, 412, 403, 393, 384, 375, 365, 356, 346, 337, 328, 318, 309, 300, 291, 282, 273, 264, 255, 246, 237, 228, 220, 211, 203, 195, 187, 179, 171, 163, 155, 148, 140, 133, 126, 119, 112, 106, 99, 93, 87, 81, 76, 70, 65, 60, 55, 50, 45, 41, 37, 33, 29, 26, 22, 19, 17, 14, 12, 9, 7, 6, 4, 3, 2, 1, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 9, 12, 14, 17, 19, 22, 26, 29, 33, 37, 41, 45, 50, 55, 60, 65, 70, 76, 81, 87, 93, 99, 106, 112, 119, 126, 133, 140, 148, 155, 163, 171, 179, 187, 195, 203, 211, 220, 228, 237, 246, 255, 264, 273, 282, 291, 300, 309, 318, 328, 337, 346, 356, 365, 375,};
volatile uint16_t phaseA_index = 0; volatile uint16_t phaseB_index = SINE_TABLE_SIZE / 3; volatile uint16_t phaseC_index = (2 * SINE_TABLE_SIZE) / 3;
// Variables for V/F control volatile uint16_t amplitude_scaling = 784; // Default to maximum amplitude volatile uint16_t frequency_scaling = 1; // Not used in this version
// Timer0 variables volatile uint8_t tmr0_reload_value = 0;
void update_pwm(void); void init_ADC(void); uint16_t read_ADC(uint8_t channel); void init_PWM(void); void init_Timer0(uint16_t freq_adc); void init_Oscillator(void); void init_PPS(void);
void update_pwm(void) { // Get the raw sine values uint16_t raw_dutyA = sine_table[phaseA_index]; uint16_t raw_dutyB = sine_table[phaseB_index]; uint16_t raw_dutyC = sine_table[phaseC_index];
// Scale the amplitude based on the amplitude_scaling factor (0 to 1023) uint16_t dutyA = (raw_dutyA * amplitude_scaling) / 784; uint16_t dutyB = (raw_dutyB * amplitude_scaling) / 784; uint16_t dutyC = (raw_dutyC * amplitude_scaling) / 784;
// Set PWM duty cycles (10-bit values) PWM1DCH = (dutyA >> 2) & 0xFF; PWM1DCL = (dutyA & 0x0003) << 6;
PWM2DCH = (dutyB >> 2) & 0xFF; PWM2DCL = (dutyB & 0x0003) << 6;
PWM3DCH = (dutyC >> 2) & 0xFF; PWM3DCL = (dutyC & 0x0003) << 6;
// Increment phase indexes by 1 phaseA_index = (phaseA_index + 1) % SINE_TABLE_SIZE; phaseB_index = (phaseB_index + 1) % SINE_TABLE_SIZE; phaseC_index = (phaseC_index + 1) % SINE_TABLE_SIZE;
}
void main(void) { init_Oscillator(); init_PWM(); init_PPS(); init_ADC();
// Initial frequency setup uint16_t freq_adc = read_ADC(1); // Initial frequency ADC value init_Timer0(freq_adc); // Initialize Timer0 with initial frequency
// Enable interrupts INTCONbits.TMR0IE = 1; // Enable Timer0 interrupt INTCONbits.PEIE = 1; // Enable Peripheral Interrupts INTCONbits.GIE = 1; // Enable Global Interrupts
while (1) { // Read ADC values for amplitude and frequency amplitude_scaling = read_ADC(0); // 10-bit result (0 to 1023) freq_adc = read_ADC(1); // 10-bit result (0 to 1023)
// Update Timer0 settings based on frequency ADC input init_Timer0(freq_adc);}
}
void __interrupt() ISR(void) { if (INTCONbits.TMR0IF) { INTCONbits.TMR0IF = 0; // Clear Timer0 interrupt flag
// Reload TMR0 TMR0 = tmr0_reload_value; // Update PWM outputs update_pwm();}
// Add ADC interrupt handling if using interrupt-driven ADC (optional)
}
void init_ADC(void) { // Configure ADC ADCON1bits.ADCS = 0b110; // ADC Conversion Clock FOSC/64 ADCON1bits.ADFM = 1; // Right justified result ADCON1bits.ADPREF = 0b00; // Vref+ is Vdd
// Configure ADC input channels ANSELAbits.ANSA0 = 1; // RA0 as analog input (AN0) ANSELAbits.ANSA1 = 1; // RA1 as analog input (AN1)
TRISAbits.TRISA0 = 1; // Set RA0 as input TRISAbits.TRISA1 = 1; // Set RA1 as input
ADCON0bits.ADON = 1; // Turn on ADC
}
uint16_t read_ADC(uint8_t channel) { // Select ADC channel ADCON0bits.CHS = channel; // Select ADC channel __delay_us(5); // Acquisition time
// Start conversion ADCON0bits.GO_nDONE = 1; while (ADCON0bits.GO_nDONE); // Wait for conversion to complete
// Get ADC result uint16_t result = ((ADRESH << 8) | ADRESL); return result; // 10-bit result
}
void init_PWM(void) { // Configure Timer2 for PWM T2CONbits.T2CKPS = 0b00; // Prescaler = 1 PR2 = 199; // PR2 value for 20 kHz PWM frequency T2CONbits.TMR2ON = 1; // Enable Timer2
// Configure PWM Modules PWM1CONbits.PWM1POL = 0; // Active-high PWM1CONbits.PWM1OE = 1; // PWM1 Output Enable PWM1CONbits.PWM1EN = 1; // Enable PWM1
PWM2CONbits.PWM2POL = 0; PWM2CONbits.PWM2OE = 1; PWM2CONbits.PWM2EN = 1;
PWM3CONbits.PWM3POL = 0; PWM3CONbits.PWM3OE = 1; PWM3CONbits.PWM3EN = 1;
}
void init_Timer0(uint16_t freq_adc) { // Configure Timer0 for updates based on frequency ADC value // Calculate the Timer0 preload value to achieve desired sine wave frequency
// Constants uint32_t FOSC = 16000000UL; // 16 MHz uint32_t F_TIMER0 = FOSC / 4; // Timer0 clock frequency (Fosc/4) = 4 MHz uint8_t prescaler = 16; // Prescaler value (options: 2, 4, 8, 16, 32, 64, 128, 256)
// Map freq_adc (0-1023) to desired frequency range (e.g., 10 Hz to 200 Hz) // Adjust the frequency range as needed uint16_t min_freq = 10; // Minimum frequency in Hz uint16_t max_freq = 200; // Maximum frequency in Hz
// Map freq_adc to frequency uint16_t desired_freq = min_freq + ((uint32_t)(max_freq - min_freq) * freq_adc) / 1023;
if (desired_freq < min_freq) desired_freq = min_freq; if (desired_freq > max_freq) desired_freq = max_freq;
// Calculate the Timer0 interrupt interval (in seconds) double interrupt_interval = 1.0 / (desired_freq * SINE_TABLE_SIZE);
// Calculate the required Timer0 counts uint32_t timer_counts = interrupt_interval * F_TIMER0 / prescaler;
// Ensure timer_counts is less than 256 (8-bit Timer0) if (timer_counts > 255) { timer_counts = 255; } else if (timer_counts < 2) { timer_counts = 2; // Minimum practical value }
// Calculate the preload value tmr0_reload_value = 256 - (uint8_t)timer_counts;
// Configure Timer0 OPTION_REGbits.T0CS = 0; // Timer0 Clock Source: Internal (FOSC/4) OPTION_REGbits.PSA = 0; // Prescaler assigned to Timer0 OPTION_REGbits.PS = 0b100; // Prescaler = 1:16
// Set TMR0 to reload value TMR0 = tmr0_reload_value;
}
void init_Oscillator(void) { // Oscillator configuration OSCCONbits.IRCF = 0b1111; // 16 MHz internal oscillator OSCCONbits.SCS = 0b10; // Internal oscillator } move Tmr0 calculations into adc module and only need 10hz to 60hz
- Assistant
To move the Timer0 calculations into the ADC module and adjust the frequency range to 10 Hz to 60 Hz, you'll need to modify your code in two main ways:
-
Adjust the frequency range in the
init_Timer0()function. -
Relocate the Timer0 initialization call so that it resides within the ADC module.
Here's how you can implement these changes:
1. Adjust the Frequency Range in
init_Timer0()In the
init_Timer0()function, you need to update themin_freqandmax_freqvariables to reflect the desired frequency range of 10 Hz to 60 Hz.Modify
init_Timer0()as follows:void init_Timer0(uint16_t freq_adc) { // Configure Timer0 for updates based on frequency ADC value // Calculate the Timer0 preload value to achieve desired sine wave frequency // Constants uint32_t FOSC = 16000000UL; // 16 MHz uint32_t F_TIMER0 = FOSC / 4; // Timer0 clock frequency (Fosc/4) = 4 MHz uint8_t prescaler = 16; // Prescaler value (options: 2, 4, 8, 16, 32, 64, 128, 256) // Map freq_adc (0-1023) to desired frequency range (10 Hz to 60 Hz) uint16_t min_freq = 10; // Minimum frequency in Hz uint16_t max_freq = 60; // Maximum frequency in Hz // Map freq_adc to frequency uint16_t desired_freq = min_freq + ((uint32_t)(max_freq - min_freq) * freq_adc) / 1023; if (desired_freq < min_freq) desired_freq = min_freq; if (desired_freq > max_freq) desired_freq = max_freq; // Calculate the Timer0 interrupt interval (in seconds) double interrupt_interval = 1.0 / (desired_freq * SINE_TABLE_SIZE); // Calculate the required Timer0 counts uint32_t timer_counts = interrupt_interval * F_TIMER0 / prescaler; // Ensure timer_counts is within 8-bit Timer0 range if (timer_counts > 255) { timer_counts = 255; } else if (timer_counts < 2) { timer_counts = 2; // Minimum practical value } // Calculate the preload value tmr0_reload_value = 256 - (uint8_t)timer_counts; // Configure Timer0 OPTION_REGbits.T0CS = 0; // Timer0 Clock Source: Internal (FOSC/4) OPTION_REGbits.PSA = 0; // Prescaler assigned to Timer0 OPTION_REGbits.PS = 0b100; // Prescaler = 1:16 // Set TMR0 to reload value TMR0 = tmr0_reload_value; }
2. Move Timer0 Calculations into the ADC Module
To relocate the Timer0 calculations into the ADC module, create a new function within the ADC module that reads the frequency ADC value and updates the Timer0 settings accordingly.
Add the following function to your code:
void update_frequency(void) { uint16_t freq_adc = read_ADC(1); // Read ADC channel 1 for frequency init_Timer0(freq_adc); // Update Timer0 settings based on freq_adc }This function reads the ADC value from channel 1 (which we'll assume is your frequency control input) and then calls
init_Timer0()with the ADC value to update the Timer0 settings.Update your
main()function to useupdate_frequency():void main(void) { init_Oscillator(); init_PWM(); init_PPS(); init_ADC(); // Initial frequency setup update_frequency(); // Initialize Timer0 with initial frequency // Enable interrupts INTCONbits.TMR0IE = 1; // Enable Timer0 interrupt INTCONbits.PEIE = 1; // Enable Peripheral Interrupts INTCONbits.GIE = 1; // Enable Global Interrupts while (1) { // Read ADC values for amplitude and update frequency amplitude_scaling = read_ADC(0); // 10-bit result (0 to 1023) update_frequency(); // Read freq ADC and update Timer0 settings } }By calling
update_frequency()in both the initialization phase and within the main loop, you ensure that the Timer0 settings are updated whenever the frequency control input changes.
Note: Make sure to remove or comment out any previous calls to
init_Timer0(freq_adc)that were outside of the ADC module to avoid redundant calls.
Full Updated Code Snippet for Reference
Here are the relevant portions of your code with the changes applied:
// Updated init_Timer0() with new frequency range void init_Timer0(uint16_t freq_adc) { // ... [As shown above] } // New function in ADC module to update frequency and Timer0 settings void update_frequency(void) { uint16_t freq_adc = read_ADC(1); // Read ADC channel 1 for frequency init_Timer0(freq_adc); // Update Timer0 settings based on freq_adc } // Updated main() function void main(void) { init_Oscillator(); init_PWM(); init_PPS(); init_ADC(); // Initial frequency setup update_frequency(); // Initialize Timer0 with initial frequency // Enable interrupts INTCONbits.TMR0IE = 1; // Enable Timer0 interrupt INTCONbits.PEIE = 1; // Enable Peripheral Interrupts INTCONbits.GIE = 1; // Enable Global Interrupts while (1) { // Read ADC values for amplitude and update frequency amplitude_scaling = read_ADC(0); // 10-bit result (0 to 1023) update_frequency(); // Read freq ADC and update Timer0 settings } }
With these changes:
- The Timer0 calculations are now part of the ADC module through the
update_frequency()function. - The frequency range is set to 10 Hz to 60 Hz as per your requirement.
- The main loop remains clean and simply calls
update_frequency()to handle both reading the ADC and updating the Timer0 settings.
Ensure you test the updated code thoroughly to verify that the frequency control operates correctly within the new range and that the Timer0 interrupts occur as expected.
-
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.