Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-2024-05-13· OpenAIAi2 WildChat-4.8M (AI2)

my VM on virtualbox is using static IP, how to config it to use my host's VPN?

  1. User

    my VM on virtualbox is using static IP, how to config it to use my host's VPN?

  2. Assistant

    To have your VirtualBox VM use your host's VPN, you need to configure the VM's network settings in a way that directs its traffic through the host machine, which is connected to the VPN. The typical way to do this is to use a NAT Network or Bridged Adapter with proper DNS configurations. Here's how you can achieve this:

    Step 1: Configure VM Network Settings

    1. Open VirtualBox: Launch VirtualBox Manager.

    2. Select Your VM: Select the VM you want to configure and make sure it is powered off.

    3. Open Network Settings: Go to Settings > Network.

    4. Choose Network Attachment:

      • If you want to use NAT Network:

        • Under Adapter 1, select Enable Network Adapter.
        • Set Attached to to NAT.
      • If you want to use Bridged Adapter (this will allow your VM to appear as another device on the same local network as your host):

        • Under Adapter 1, select Enable Network Adapter.
        • Set Attached to to Bridged Adapter.
    5. Check Network Adapters: Make sure no other network adapters are enabled unless you need them for specific purposes (e.g., Host-only Adapter).

    Step 2: Ensure DNS Resolution Through VPN

    This ensures that DNS requests from the VM go through the VPN's DNS.

    1. Static IP Configuration:

      • If you are using a static IP address, make sure you also set the DNS servers to those provided by your VPN service in the guest OS's network configuration settings.
    2. Dynamic IP Configuration:

      • If you decide to use DHCP instead, it will depend on the network mode:
        • For NAT: VirtualBox will route traffic through your host, including the VPN.
        • For Bridged Adapter: The VM would get an IP address from the same pool as the host, typically through the local router.

    Step 3: Verify Connection

    1. Boot Your VM: Start the VM from VirtualBox.

    2. Check the IP and DNS:

      • If using static IP, check the guest OS network settings to ensure the correct IP, Subnet Mask, Gateway, and DNS are configured.
      • Use ipconfig (on Windows) or ifconfig (on Unix systems) to verify the network settings.
    3. Test Internet Connectivity:

      • Open a terminal or command prompt in your VM and try to ping a website (e.g., ping google.com). If DNS is set up correctly through the VPN, the response should be resolved through the VPN's DNS servers.
    4. Check IP:

      • You can use a service like whatismyip.com in your VM's browser to verify whether the IP it sees matches your VPN's exit IP address.

    Troubleshooting

    • No Connectivity:

      • Make sure your host is connected to the VPN first.
      • Ensure your firewall settings on the host and VM are not blocking the connections.
    • Incorrect IP:

      • Ensure you have configured the correct DNS servers when using a static IP.
    • DNS Leak:

      • Double-check that DNS requests are routed through the VPN. You might need to check the VPN configuration or use specific VPN-compatible DNS servers.

    By following the steps above, you should be able to configure your VirtualBox VM to use your host's VPN connection, ensuring that all network traffic from the VM goes through the VPN tunnel on the host machine.

  3. User

    I am using letsvpn, how to check its DNS servers?

  4. Assistant

    To find out the DNS servers used by LetsVPN, you can try the following methods:

    Method 1: Check DNS Servers via Command Line

    1. Connect to LetsVPN: Ensure that your host machine is connected to LetsVPN.

    2. Check DNS Servers (Windows):

      • Open Command Prompt with administrative privileges.
      • Run the following command:
        ipconfig /all
        
      • Look for the section corresponding to your VPN adapter. It should list the DNS servers being used.
    3. Check DNS Servers (macOS/Linux):

      • Open Terminal.

      • For macOS, run the following command:

        scutil --dns
        

        Look under the resolver section for the DNS configuration when connected to the VPN.

      • For Linux, use the command:

        nmcli dev show
        

        Look for IP4.DNS in the output under the relevant network interface.

    Method 2: Use a Web-Based DNS Leak Test

    1. Connect to LetsVPN: Ensure your host machine is connected to LetsVPN.

    2. Perform a DNS Leak Test:

      • Open a web browser and navigate to a DNS leak test site like dnsleaktest.com.
      • Start the test. The DNS servers listed in the results are the ones that your VPN is using.

    Method 3: Examine VPN Configuration Files (Advanced Users)

    If you're comfortable with configuration files and if LetsVPN provides configuration files for manual setup (such as .ovpn files for OpenVPN), you can directly check these files:

    1. Locate Configuration Files:

      • Find the configuration files provided by LetsVPN for manual VPN setup.
    2. Examine Configuration:

      • Open the configuration file (e.g., xxxx.ovpn) in a text editor.
      • Look for lines starting with dhcp-option DNS, which will list the DNS servers.

    Once You Have the DNS Servers

    1. Configure Your VM:
      • In your VM, whether it's set up with a static IP or dynamic IP, manually configure the DNS servers to match those used by LetsVPN.

    Example for Windows VM:

    1. Open Network and Sharing Center.
    2. Click on Change adapter settings.
    3. Right-click your network adapter and select Properties.
    4. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
    5. Choose Use the following DNS server addresses and enter the DNS servers you found.

    Example for Linux VM:

    1. Edit your network configuration file (e.g., /etc/network/interfaces, /etc/resolv.conf, or your network manager settings) to include the DNS servers.
    2. For /etc/resolv.conf, it might look like this:
      nameserver 8.8.8.8
      nameserver 8.8.4.4
      
      Replace 8.8.8.8 and 8.8.4.4 with the DNS servers of LetsVPN.

    By following these steps, you should be able to identify and configure your VM to use the DNS servers provided by LetsVPN, ensuring your network traffic is properly routed through the VPN's DNS servers.

  5. User

    The DNS of LetsVPN is "fec0:0:0:ffff::1%1", it's using IP6, is it ok to update my VM DNS server with this one?

  6. Assistant

    Using an IPv6 DNS server on your VM is fine, provided your network and VM support IPv6. Here's how to configure it:

    For Windows VM:

    1. Open Network Settings:

      • Go to Control Panel > Network and Internet > Network and Sharing Center.
      • Click on Change adapter settings on the left sidebar.
    2. Select Network Adapter:

      • Right-click on your VM's network adapter and select Properties.
    3. Configure IPv6 DNS:

      • Select Internet Protocol Version 6 (TCP/IPv6) and click Properties.
      • Select Use the following DNS server addresses.
      • Enter fec0:0:0:ffff::1%1 into the Preferred DNS server field.
      • Leave the Alternate DNS server field blank or add another IPv6 DNS if you have one.
    4. Save and Apply:

      • Click OK to save the settings.
      • Close any remaining dialog boxes and restart the network adapter if needed.

    For Linux VM:

    1. Open Terminal: Access your terminal or SSH into your VM.

    2. Edit Network Configuration: Depending on your Linux distribution, you might edit different files. Common methods include:

      • Using NetworkManager:

        • If you use NetworkManager, you can use the nm-connection-editor GUI, or edit the respective configuration files.
        • Run sudo nm-connection-editor
        • Select your network connection, click IPv6 settings, and then manually add the DNS server fec0:0:0:ffff::1%1.
      • Using /etc/network/interfaces (Debian-based systems): Open the configuration file with a text editor:

        sudo nano /etc/network/interfaces
        

        Add or modify the DNS entries for your network interface:

        iface eth0 inet6 static
            address <your_ipv6_address>
            netmask <your_netmask>
            gateway <your_gateway>
            dns-nameservers fec0:0:0:ffff::1%1
        
      • Using /etc/netplan/01-netcfg.yaml (modern Ubuntu): Open the Netplan configuration file with a text editor:

        sudo nano /etc/netplan/01-netcfg.yaml
        

        Add the IPv6 DNS configuration:

        network:
          version: 2
          ethernets:
            eth0:
              dhcp4: no
              dhcp6: no
              addresses:
                - <your_ipv6_address>/<prefix_length>
              gateway6: <your_gateway_ipv6>
              nameservers:
                addresses:
                  - fec0:0:0:ffff::1%1
        

        Apply the changes:

        sudo netplan apply
        
      • Using /etc/resolv.conf: If you edit /etc/resolv.conf directly, add the DNS server entry:

        sudo nano /etc/resolv.conf
        

        Add the line:

        nameserver fec0:0:0:ffff::1%1
        
    3. Restart Networking Service: Depending on the method you used, you may need to restart the networking service:

      sudo systemctl restart networking
      

      or for NetworkManager:

      sudo systemctl restart NetworkManager
      

    Validate DNS Configuration

    1. Windows:

      • Open Command Prompt and run:
        nslookup
        
      • Verify the DNS server is listing fec0:0:0:ffff::1%1.
    2. Linux:

      • Open Terminal and run:
        nslookup
        
      • Verify the DNS server is listing fec0:0:0:ffff::1%1.

    By following these steps, you can successfully configure your VM to use LetsVPN's IPv6 DNS server. Ensure your network and VM support IPv6 for proper functionality.

  7. User

    after using the adapter, unable to ssh to VM, how to fix it?

  8. Assistant

    If you are unable to SSH into your VM after changing the network adapter settings, there are a few common issues and debugging steps to consider. Let's go through a few steps that should help you diagnose and resolve the issue:

    Step 1: Check Network Configuration

    1. Revert changes: If you can, revert the settings to their original state to check if the issue is related to the network adapter change.

    2. Check Network Mode: Make sure your VM network adapter is set to either "NAT" or "Bridged Adapter" based on your requirements.

    3. Verify IP Address: Make sure the VM has an IP address assigned. Open a terminal directly on the VM and run:

      ip addr show
      

      or

      ifconfig
      

      Note the IP address of the VM.

    4. Ping the VM IP: From your host machine, try to ping the VM's IP address to check connectivity:

      ping <VM_IP_ADDRESS>
      

    Step 2: Check SSH Service

    1. Ensure SSH is Installed and Running: On the VM, check if the SSH service is installed, running, and configured to start at boot.
      • For Ubuntu/Debian:

        sudo apt update
        sudo apt install openssh-server
        sudo systemctl status ssh
        sudo systemctl start ssh
        sudo systemctl enable ssh
        
      • For CentOS/RHEL:

        sudo yum install openssh-server
        sudo systemctl status sshd
        sudo systemctl start sshd
        sudo systemctl enable sshd
        

    Step 3: Firewall and Security Groups

    1. Check Firewall on VM: Ensure the firewall rules on the VM itself are not blocking SSH (port 22).

      • On Ubuntu/Debian:
        sudo ufw status
        sudo ufw allow ssh
        
      • On CentOS/RHEL:
        sudo firewall-cmd --permanent --add-service=ssh
        sudo firewall-cmd --reload
        
    2. Check Host Firewall: Ensure that your host machine firewall is not blocking outgoing SSH requests.

    Step 4: SSH Configuration

    1. Verify SSH Configuration: Make sure the SSH configuration file (/etc/ssh/sshd_config) on the VM does not restrict connections.
      • Check for PermitRootLogin or AllowUsers directives.
      • Ensure the Port directive is set to 22 and not some alternative port unless you're using a custom port.

    Step 5: SSH Command and Network Adapter

    1. Specify Network Adapter: If using Bridged Adapter, ensure your VM is connected to the same network as your host.

    2. Use Correct IP and Port: Make sure you are using the correct IP address and port when trying to SSH.

      ssh user@<VM_IP_ADDRESS>
      

    Specific Nat Network Configurations

    If using NAT Network and Port Forwarding:

    1. Configure Port Forwarding:

      • Go to Settings > Network > Advanced > Port Forwarding for your VM.
      • Add a rule to forward host port to the guest port 22:
        • Name: SSH
        • Protocol: TCP
        • Host IP: (leave empty or set to 127.0.0.1)
        • Host Port: 2222 (or some unused port)
        • Guest IP: (leave empty)
        • Guest Port: 22
    2. Connect via Port Forwarding:

      ssh -p 2222 user@localhost
      

    Final Check: Logs

    1. Check SSH and System Logs: On the VM, check SSH and system logs for any hints or error messages.
      sudo tail -f /var/log/auth.log  # for Ubuntu/Debian based systems
      sudo tail -f /var/log/secure   # for CentOS/RHEL based systems
      

    By following these steps, you should be able to diagnose and resolve the issue causing the inability to SSH into your VM. If you still face issues, consider providing specific error messages or behavior to get more targeted assistance.

  9. User

    below is the adaptor using VPN "未知适配器 LetsTAP:

    连接特定的 DNS 后缀 . . . . . . . : 描述. . . . . . . . . . . . . . . : TAP-Windows Adapter V9 物理地址. . . . . . . . . . . . . : 00-FF-21-5E-56-9F DHCP 已启用 . . . . . . . . . . . : 否 自动配置已启用. . . . . . . . . . : 是 本地链接 IPv6 地址. . . . . . . . : fe80::8a8c:b9d3:dd0b:adca%5(首选) IPv4 地址 . . . . . . . . . . . . : 26.26.26.1(首选) 子网掩码 . . . . . . . . . . . . : 255.255.255.248 默认网关. . . . . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 1057029921 DHCPv6 客户端 DUID . . . . . . . : 00-01-00-01-25-24-AF-9D-B0-52-16-42-14-AF DNS 服务器 . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1", I have enabled to VM to use "TAP-Windows Adapter V9", but unable to ssh to the VM

  10. Assistant

    Given your setup, with the TAP-Windows Adapter V9 being used and a static IP configuration for the VM, there are a few things you need to check and configure to ensure you can SSH into your VM.

    Step-by-Step Guide

    1. Verify the Network Adapter Configuration in VirtualBox:

      • Open VirtualBox.
      • Select your VM and go to Settings > Network.
      • Select the appropriate network adapter (e.g., Adapter 1).
      • Make sure the adapter is Attached to either Bridged Adapter or Host-only Adapter.
      • For Bridged Adapter, make sure it’s using the TAP-Windows Adapter V9.
    2. Check the VM's IP Configuration:

      • Boot into your VM.
      • Open a terminal and run:
        ip addr show
        
      • Ensure that the VM has an appropriate IP address in the same subnet as the host's TAP-Windows Adapter V9.
    3. Ping the VM from the Host:

      • From the host, open a command prompt or terminal.
      • Ping the VM’s IP address to ensure connectivity:
        ping <VM_IP_ADDRESS>
        
    4. Check and Install SSH on the VM:

      • If SSH is not installed or running on the VM, install and start it.
      • For Ubuntu/Debian:
        sudo apt update
        sudo apt install openssh-server
        sudo systemctl enable ssh
        sudo systemctl start ssh
        
      • For CentOS/RHEL:
        sudo yum install openssh-server
        sudo systemctl enable sshd
        sudo systemctl start sshd
        
    5. Check the VM's Firewall Rules:

      • Ensure that the VM's firewall allows SSH (port 22).
      • For Ubuntu/Debian:
        sudo ufw allow ssh
        sudo ufw enable
        
      • For CentOS/RHEL:
        sudo firewall-cmd --permanent --add-service=ssh
        sudo firewall-cmd --reload
        
    6. Optional: Configure Port Forwarding in VirtualBox (if NAT):

      If you are using NAT, you may need to configure port forwarding to access SSH.

      • In VirtualBox, with the VM selected, go to Settings > Network.
      • Click Advanced, then Port Forwarding.
      • Add a new rule:
        • Name: SSH
        • Protocol: TCP
        • Host IP: 127.0.0.1 (or leave blank)
        • Host Port: 2222 (or another unused port)
        • Guest IP: (leave blank)
        • Guest Port: 22
      • Connect using:
        ssh -p 2222 user@localhost
        

    Verify your TAP Adapter Settings

    Given your TAP-Windows Adapter V9 has an IPv4 address of 26.26.26.1 with a subnet mask of 255.255.255.248, make sure your VM has a static IP in the same range, but not the same as the host's TAP IP:

    • Suitable IPs for VM in the subnet: 26.26.26.2 to 26.26.26.6
    • Example Network Configuration for the VM:
      • IP Address: 26.26.26.2
      • Subnet Mask: 255.255.255.248
      • Gateway: (none, unless there's a router in this virtual network)
      • DNS Server: fec0:0:0:ffff::1%1 (if IPv6 is required)

    Example for Linux VM configuration:

    1. Static IP Configuration:

      • Edit /etc/network/interfaces (Ubuntu/Debian based systems):

        sudo nano /etc/network/interfaces
        

        Add the following (adapt as necessary):

        auto eth0
        iface eth0 inet static
          address 26.26.26.2
          netmask 255.255.255.248
          gateway 26.26.26.1
          dns-nameservers fec0:0:0:ffff::1%1
        
      • For /etc/netplan/config.yaml (modern Ubuntu):

        sudo nano /etc/netplan/01-netcfg.yaml
        

        Add/modify:

        network:
          version: 2
          ethernets:
            eth0:
              addresses: [26.26.26.2/29]
              gateway4: 26.26.26.1
              nameservers:
                addresses:
                  - fec0:0:0:ffff::1%1
        

        Apply the configuration:

        sudo netplan apply
        
    2. Restart Network Services:

      • Restart the networking services:
        sudo systemctl restart networking
        

    Final Steps

    1. Reconnect to the VM via SSH:

      Try to SSH into your VM from the host machine:

      ssh user@26.26.26.2
      
    2. Check Logs for Errors:

      If you cannot connect, check your VM's SSH logs:

      sudo tail -f /var/log/auth.log  # Ubuntu/Debian
      sudo tail -f /var/log/secure   # CentOS/RHEL
      
    3. Firewall and Security Settings on Host:

      Ensure that your host machine’s firewall or security software is not blocking the SSH connection to the VM.

    By carefully following these steps and verifying each part of the configuration, you should be able to SSH into your VM through the VPN-connected adapter.

  11. User

    unable to ping VM ip from the local host

  12. Assistant

    If you're unable to ping your VM's IP address from your local host, it indicates there is a connectivity issue that needs to be addressed. Let's go through some detailed steps to diagnose and fix this problem.

    Step-by-Step Troubleshooting

    1. Verify Network Adapter Settings

    First, ensure your VM's network adapter settings are correctly configured.

    For VirtualBox:

    • Open VirtualBox.
    • Select your VM and go to Settings > Network.
    • Ensure one adapter is enabled and set to Bridged Adapter.
    • Choose the TAP-Windows Adapter V9 from the Name dropdown.

    2. Check VM's IP Configuration

    Boot into your VM and make sure it has an IP address in the same subnet as the TAP adapter.

    In VM (Linux):

    ip addr show
    

    In VM (Windows):

    ipconfig /all
    

    Verify that the IP address, subnet mask, and default gateway are appropriate.

    3. Static IP Configuration

    Ensure that the VM's IP is correctly configured to match the subnet.

    Example for Linux VM (Debian/Ubuntu-based):

    1. Edit network interfaces:
      sudo nano /etc/network/interfaces
      
      Add the following (adapt as necessary):
      auto eth0
      iface eth0 inet static
        address 26.26.26.2
        netmask 255.255.255.248
        gateway 26.26.26.1
      
    2. Restart network services:
      sudo systemctl restart networking
      

    Example for Linux VM (Netplan - modern Ubuntu):

    1. Edit Netplan configuration:
      sudo nano /etc/netplan/01-netcfg.yaml
      
      Add/modify:
      network:
        version: 2
        ethernets:
          eth0:
            addresses: [26.26.26.2/29]
            gateway4: 26.26.26.1
            nameservers:
              addresses: [fec0:0:0:ffff::1%1]
      
    2. Apply the configuration:
      sudo netplan apply
      

    4. Ensure Services are Running

    Make sure SSH and other required services are running on the VM.

    1. SSH service check for Linux:

      sudo systemctl status sshd  # or ssh
      sudo systemctl start sshd
      sudo systemctl enable sshd
      
    2. Check firewall settings:

      • For Linux (Debian/Ubuntu):

        sudo ufw allow ssh
        sudo ufw enable
        
      • For Linux (CentOS/RHEL):

        sudo firewall-cmd --permanent --add-service=ssh
        sudo firewall-cmd --reload
        

    5. Test Network Connectivity Within VM

    From inside the VM, attempt to ping the host or another machine on the same network to ensure the VM itself has connectivity beyond its interface.

    In VM:

    ping 26.26.26.1  # Host's TAP adapter IP
    

    6. Check Host Machine Configuration

    1. Verify Host Network Configuration: On the host machine, ensure the TAP-Windows Adapter V9 is configured properly:

      In Windows:

      • Open Control Panel > Network and Sharing Center > Change adapter settings.
      • Right-click TAP-Windows Adapter V9 and select Properties.
      • Ensure TCP/IPv4 and TCP/IPv6 are both enabled and configured properly.
    2. Disable/Configure Host Firewall: Ensure that the host firewall allows traffic from/to the TAP-Windows Adapter V9 and the VM's IP address.

    In Windows:

    • Open Control Panel > System and Security > Windows Defender Firewall.
    • Click on Advanced settings and add inbound/outbound rules to allow traffic on the necessary ports (e.g., TCP 22 for SSH).

    7. Cross-Check Subnet and IP Range

    Ensure that all devices (host and VM) are on the same subnet and there are no IP conflicts.

    Valid range considering your subnet (255.255.255.248):

    • Network Address: 26.26.26.0
    • Usable IPs: 26.26.26.1 to 26.26.26.6
    • Broadcast Address: 26.26.26.7

    8. Bridge Configuration on Host

    Ensure the TAP-Windows Adapter V9 is correctly functioning and bridging:

    1. Check TAP Adapter Status:

      • Right-click the network icon in your system tray.
      • Select Open Network & Internet settings > Change adapter options.
    2. Bridge if Necessary: If you're using a Bridged Adapter, ensure that the TAP device is correctly bridged.

    9. Final Network Tests

    1. Ping Test: From the host:

      ping 26.26.26.2  # VM's IP Address
      
    2. SSH Connection Attempt:

      ssh user@26.26.26.2
      

    If these configurations and tests are followed correctly, this should resolve the connectivity issue and allow you to properly SSH into your VM. If you still encounter issues, please provide specific error messages or logs for further troubleshooting.

  13. User

    I can not change the VM static IP, because my k8s is running with the IP, how can I use the host VPN?

  14. Assistant

    Given that you cannot change the static IP of your VM because it is being used by your Kubernetes setup, you still need to ensure that the VM can route its traffic through your host's VPN. Let's focus on solutions that allow this while keeping your static IP configurations intact.

    Scenario Overview

    1. Host Machine: Connected to VPN using TAP-Windows Adapter V9.
    2. VM: Static IP fixed due to Kubernetes setup.

    Steps to Ensure VM Uses Host's VPN

    Step 1: Verify VM Network Adapter in VirtualBox

    1. Set Network Adapter to Bridged Mode:
      • Open VirtualBox.
      • Select your VM and go to Settings > Network.
      • Set the first adapter to Bridged Adapter.
      • Choose TAP-Windows Adapter V9 from the Name dropdown.

    Step 2: Ensure Proper Network Configuration for VM and Host

    Given that your VM already has a static IP configured, ensure that the VM IP is not conflicted within the subnet provided by the TAP-Windows Adapter V9.

    Step 3: Routing Configuration on the Host

    1. Enable IP Forwarding on the Host:

      • On your Windows Host machine, you need to enable IP forwarding so that traffic from your VM can be correctly routed through the VPN.

      To enable IP forwarding in Windows:

      1. Press Win + R to open the Run dialog, type regedit, and hit Enter.
      2. Navigate to:
        HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
        
      3. Find IPEnableRouter and set its value to 1. If it does not exist, create a new DWORD (32-bit) value named IPEnableRouter and set it to 1.
    2. Restart the System:

      • To apply these changes, you might need to restart your machine.

    Step 4: Configure VM to Use Host as Gateway

    1. Add Routing Rules on the VM:

      • SSH into the VM or access the VM's terminal directly.
      • Add a static route to route all traffic through the host's TAP adapter.

      Linux VM Example:

      sudo ip route add default via 26.26.26.1
      

      This assumes that 26.26.26.1 is the IP address of the host's TAP adapter, which is also the default gateway for your VM.

    Note: If your default via is already set, ensure it aligns with necessary routing through the VPN.

    Step 5: DNS Configuration

    Make sure your DNS is also configured to use the VPN through the host.

    1. Change DNS Settings on VM:

      • Edit /etc/resolv.conf to add or use the VPN's DNS server.
        sudo nano /etc/resolv.conf
        
        Add the following lines:
        nameserver fec0:0:0:ffff::1%1
        nameserver fec0:0:0:ffff::2%1
        nameserver fec0:0:0:ffff::3%1
        
    2. Make Changes Persistent:

      • Ensure that these changes persist across reboots. This might involve editing your network configuration files depending on distribution (e.g., netplan for Ubuntu).

    Final Steps

    1. Test Network Connectivity:

      • From the VM, attempt to ping an external site and trace the route.
        ping google.com
        traceroute google.com
        
    2. Test SSH Connection:

      • Verify you can access your services as required, and traffic routes through the VPN.

    Summary: By bridging your adapter in VirtualBox, setting IP forwarding on the host, updating routing tables on the VM, and ensuring DNS configuration is correct, your VM should leverage the host's VPN without needing to change the static IP of the VM.