Skip to content
TheChatArchiveThe Chat Archive
gpt-4o-2024-05-13· OpenAIAi2 WildChat-4.8M (AI2)

ULN2803 Low-Side Drivers and UDN2983 High-Side Drivers - YouTube…

  1. User

    ULN2803 Low-Side Drivers and UDN2983 High-Side Drivers - YouTube https://www.youtube.com/watch?v=rmnAZlvBcl8

    Transcript: (00:05) hi this is Roger from can collapse and today it's about the popular uln 2803 a Darlington driver chip or as you see it's a whole family ranging from 2801 aid up to 2805 a we'll talk about the differences later as I've had written here they are so called low side or sync drivers so what many don't know there is a companion series of ICS which are so-called high side drivers the UDM not ul and UDN 2981 through 2984 we'll talk about them in the end there you can do nice things with them for example they (00:59) go up to 80 volts they can switch up to 80 volts anyway let's go back to the basic data of the UL n 2800 it's serious the output current can be up to 500 milliamps but be aware this is not true if all outputs are switched on at the same time we will also talk about this later about what the datasheet tells us in detail the IC can switch considerably high voltage 50 volts is quite high we have integral suppression diodes that's what you see here each output has a so called freewheeling diet and they all (01:47) are tied together to a common output or common pin and we have versions versions and that's the difference between the different numbers for all popular logic families on not only TTL and five-fold CMOS but also other logic families and what many don't know the outputs can be paralleled but let's start with the use of these what's the intention behind these eight freewheeling diets so when you apply a load to the output and the output is the collector of an NPN darling all the all the emitters of the eight Darlington (02:36) transistors are tied also to a common pin to a common ground now let's suppose you're switching an inductive load which can be a relay coil or a magnet or something like that and you connect them to VCC so that's the Bart this is here the pin out of let's say output one two three four five or up to eight and your load is always connected to a positive voltage on the other side so that's where they call low side drivers when this transistor turns on it pulls the load to ground to the low side of your (03:25) power now what happens when you switch on an inductive load like the relay call well when you switch it on there is nothing that can do any harm happening the current will rise linearly so there's no problem but what happens when you switch it off well then due to the breakdown of the magnetic field you will get an induction with reverse polarity so if if we beforehand had the positive side here and the negative side of the load here now induction will create a positive voltage here and a negative voltage here and this voltage can be (04:19) hundreds sometimes even thousands of walls and that would destroy the output transistor if we don't have any means to get rid of this voltage now simple as it is just use a diet and now the induction generated voltage and current current will circulate here and the voltage here is safely on the on the collector of the output transistor is safely limited and this is what it's called a freewheeling diet because when you switch the power supply of an inductive load when you switch it off then the inductor is (05:12) hanging in the air its freewheeling and to get away with the high generated induction voltage just use the freewheeling diet and as you can see it's exactly as they have already integrated this one here you they all have a common connection and this common connection you have to and this would be here you have to connect this this is pin number 10 of the IC you have to connect this to the positive voltage of your supply for your loads so that's a nice feature that you don't need any external diodes for switching inductive (06:08) loads and now I hope you I hope this became clear how you use it and now let's go over to the other specific details of the UL and 2800 x-series so here we see the schematic of the five different types as you can see they all have the freewheeling diet they all have a discretely built a dot NPN Darlington transistor with integrated base emitter resistors and the difference the the range of the base emitter resistance and a depending on the family type a base resistor so let's take a look at the five different types the (06:59) first one the 28 or one a is for P Mo's which is two in today's world not used anymore but also for CMAs the you LM 2803 is for 15 to 14 to 15 volt P Mo's also not used very often today and the most used one is the universal type for 5 volt TTL or and that is important for 5 volt CMOS you will also be able to switch the Darlington's on with 3. (07:41) 3 volts although they are basically specified for 5 volts so if you have a micro controller output with 3.3 volts high they also will safely turn on the output if you're using the universal type 2803 a but also today still CMOS is still used the standard Sima not the h-scene CMOS is also still used because standard CMOS is capable going up to a voltage of 15 or some ices even can go up to 18 volts that can be quite nice in in some analog or digital circuitry to have 5 volt 15 volt switching capacity and for if you are using CMOS with higher than 6 volt (08:41) VCC then you should or have to use the UL and 2804 a the o4 is important because it has a different base resistor otherwise the current from a high output from a 15 volts Emil's would there would be too much base current and that drops or that draws the CMOS down and the the current is then the base current would be higher than is usually allowed with standard CMOS and we have a last one the 2805 that is for high out TTL I'm not sure what they mean by high out TTL so perhaps somebody can can give an explanation in the comments but the two (09:41) types that are mostly used is the universal 5 volt one which you can connect to basically all 3 point 3 to 5 volt digital outputs no matter if they are TTL or CMOS and the second most used one is the 2804 4 let's call it high voltage CMOS or PMO's if you still have any ICS that are working with P Mo's so let's take a closer look at the data sheet we have the output voltage of 50 volt the 500 milliamps max continuous collector current that we already knew but what you also should take into consideration the collector emitter (10:29) saturation voltage can be as high as 1 point 3 volts even in worst case 1 point 6 volts so if you're working with only a power supply of let's say 5 volts and you're switching really 500 milliamps at one output then here on the collector emitter we can have up to 1.6 or was the highest yeah what in worst case you have to take into consideration there could be already out of this 5 volt that you are using here 1 point 6 walls can be at the collector emitter so they are remaining only three point four (11:16) walls and your load should be safely working also when taking into consideration this missing one point six volts so next is the turn on and turn off delay time which might look with a quarter of a microsecond or 250 nanoseconds that might look relatively fast but in today's world of fast microcontrollers you can get a problem if you're switching for example in multiplexing big LED matrices this can be a problem even with an Arduino with it's 60 megahertz frequency you have to take this quarter of a microsecond into (12:08) consideration so that you don't get into the situation that perhaps two outputs are conducting because you didn't realize that it takes some time for one output to switch off and also for the next one to switch on and now finally we take a look at the true output current that you can get we already know a 500 milliamps is the max output current you can get but the recommended maximum current is only 400 milliamps and now it depends on how many outputs you are using at the same time so if you think that you can turn all eight outputs on (13:05) in parallel and get 500 milliamps out of them no you don't get with a what's called the duty cycle of a 100% that means all are turned on the whole time you only get 100 50 milliamps per output so the if you multiply this then you get a total output current summed up of 1.2 amps but only from all outputs if they are parallel or each one will give you only 150 milliamps now for the 500 the 400 milliamps limit for continuously turned out turned on outputs is only valid for a max of two outputs here we still just (14:00) can get two outputs with a duty cycle of 100% which means always on two outputs can really supply 400 milliamps at the same time for an extended period but if you are multiplexing and you know or mustn't be multiplexing but anyway if I'm not if the outputs are not turned on the whole time then let's take the maximum if if you are really using all eight to all eight outputs turned on but only for let's say 28% of the time which means you have a PWM signal where the on time is 28% of the period or in other (15:03) words the off time would be 72% then you can really get 400 milliamps out of all eight outputs if it's not for an extended period but only for roughly a quarter of a period so that you should know for not destroying your circuit or in other words to build a reliable power circuit so and as promised we finally take a look at the companion Sirius to the uln 2800 X the UDN 2981 through 2984 the different numbering is again for the different logic families and there is still a there are two differences the first one we already saw they are so (15:59) called high side drivers which looks like this you have your driver and the driver is connected with the positive voltage now and the output of the driver now the load goes to ground and that's why it's called high side drivers because VCC is now switched to the load and the loads if you have some of them are have a common ground connection this is sometimes necessary for example when switching VFD displays vacuum fluorescent displays which I'll make a separate tutorial about it's quite handy (16:52) to have high sight drivers and their internal structure is a bit more complicated because it's easier for for IC manufacturers to build power NPN transistors you will see we have one two three four NPN transistors and only one P and P so they must take make some effort to in in silicon to get this high side driver switching here you can see they have a common connection to the positive power supply and the output then is here the the positive power supply is switched from the high side to the load compare this again to the low (17:43) side drivers there are only two transistors plus the freewheeling diode as you can see we apparently do not have a freewheeling diet because usually you don't ah sorry I was wrong of course we have them here but of course in in reverse direction here we have the freewheeling diet going away from the collector of the output and here we have the direction to the output from the common ground to the output of the driver so there's one nice thing about them there is a standard type which can be used with a supply voltage from five to (18:43) fifty volts that's exactly what the UL m 2800 x low side drivers can do but there is also a part of the family that can go I will make it a little bit bigger so that you can better see it there is also a family type that can drive up to 80 volts that's quite high already but not lower than 35 volts so you even have the option here to drive for for as low power guys and low voltage guys comparatively or relatively high voltages and I perhaps in in my in my video about vacuum fluorescent display I'll show you an application of this IC (19:40) which I was quite a lucky that I found this IC by chance and it saved me a lot of silicon or discrete transistors when switching a VFD display so that was it for today some infos about the you LM 2008 Oh X low side and the 29 8x hi so drivers thanks for watching until next time bye from crane collapse by from Raja you bu yazının hepsini türkçeye çevir

  2. Assistant

    Tabii, işte verilen metnin tamamının Türkçeye çevrilmiş hali:

    (00:05) Merhaba, ben Raja Kankalapse'den Raja ve bugün popüler ULN2803 bir Darlington sürücü çipi hakkında konuşacağız ya da gördüğünüz gibi, 2801'den 2805'e kadar uzanan bir aile. Farklılıklar hakkında daha sonra konuşacağız. Burada yazdığım gibi bunlar, düşük taraf veya sink sürücüler olarak adlandırılmaktadır. Birçok kişinin bilmediği şey, yüksek taraf sürücüler olan UDN 2981'den 2984'e kadar olan bir dizi benzer IC olduğudur. Onlara da sonunda değineceğiz. Örneğin, onları 80 volta kadar anahtarlama yapabilirsiniz. (00:59) 80 volta kadar anahtarlama yapabilirler. Neyse, şimdi ULN2800 serisinin temel verilerine geri dönelim. Çıkış akımı 500 miliampere kadar çıkabilir, ancak dikkatli olun, bu tüm çıkışlar aynı anda açıldığında geçerli değildir. Bu konuda da datasheet'in bize detaylı olarak ne söylediğini daha sonra konuşacağız. IC, oldukça yüksek bir voltajda anahtarlama yapabilir; 50 volt oldukça yüksek bir değerdir. Bütünleşik koruma diyotları vardır; burada gördüğünüz her çıkışın bir serbest döner diyotu vardır ve hepsi ortak bir pime bağlıdır. (01:47) Ve popüler lojik aileler için versiyonları vardır, sadece TTL ve beş volt CMOS değil, diğer lojik aileler için de vardır ve birçok kişinin bilmediği şey, çıkışların paralel olarak bağlanabilmesidir. Şimdi, bu sürücüleri nasıl kullanacağımızı anlatalım. Bu sekiz serbest döner diyotun kullanımı nedir? Yani, bir yükü çıkışa uyguladığınızda ve çıkış, bir NPN Darlington transistörünün kolektörü olur. Tüm Darlington transistörlerinin emiteri de ortak bir pime bağlıdır, bu da genelde ortak bir topraktır. Şimdi, bir endüktif yükü (örneğin bir röle bobini veya bir mıknatıs) anahtarladığınızı varsayalım ve onları VCC'ye bağlarsınız. (02:36) Bu, Burada, örneğin çıkış 1, 2, 3, 4, 5 veya 8'e kadar gidebilir ve yükünüz her zaman pozitif bir voltaja bağlı olur. İşte bu yüzden onlara düşük taraf sürücüler denir; bu transistör açıldığında, yükü toprağa, güç kaynağınızın düşük tarafına çeker. Şimdi bir endüktif yükü açıp kapattığınızda ne olur? Yani açtığınızda, zararlı bir şey olmaz; akım lineer olarak yükselir, bu yüzden bir problem yoktur. Ancak kapattığınızda ne olur? O zaman, manyetik alanın çökmesi nedeniyle ters kutuplu bir indüksiyon oluşur. Daha önce buradaydı, yükün pozitif tarafı burada, negatif tarafı buradaydı; şimdi indüksiyon burada pozitif bir voltaj ve burada negatif bir voltaj yaratır ve bu voltaj (04:19) yüzlerce, bazen binlerce volt olabilir ve bu, çıkış transistörünü yok edebilir. Eğer bu voltajdan kurtulmanın bir yolu yoksa, bunu önlemek için basitçe bir diyot kullanın ve şimdi meydana gelen indüksiyon oluşturulan voltaj ve akım buradan dolaşır ve burada voltaj güvenli bir şekilde kolektörde sınırlıdır. Buna serbest döner diyot denir çünkü endüktif bir yükün güç kaynağını kapattığınızda, endüktör havada asılı kalır, serbest döner ve yüksek oluşturulan indüksiyon voltajından kurtulmak için serbest döner diyot kullanılır ve (05:12) gördüğünüz gibi, bunu zaten entegre etmişler. Hepsinin ortak bir bağlantısı vardır ve bu ortak bağlantıyı, burada gördüğünüz gibi, bu IC'nin pin numarası 10 olan bu pini yüklerinizin güç kaynağının pozitif voltajına bağlamalısınız. Bu, endüktif yükleri anahtarlamak için harici diyotlara ihtiyacınız olmadığı anlamına gelir, bu güzel bir özelliktir. Şimdi umarım bu, nasıl kullanıldığını size netleştirmiştir ve şimdi ULN2800 serisinin diğer özel ayrıntılarına göz atalım. İşte burada beş farklı tipin şeması var, gördüğünüz gibi hepsinde serbest döner diyot var, hepsinde entegre taban-emiter dirençlerine sahip bir NPN Darlington transistör var ve (06:59) bunların farkı, taban-emiter direnci ve herhangi bir aile tipine bağlı olarak bir taban direnci içerir. Şimdi bu beş farklı tipin bir analizini yapalım. İlk olarak, 2801A, günümüzde çok yaygın olarak kullanılmayan PMOS içindir ama aynı zamanda CMOS içindir. ULN 2803, günümüzde çok yaygın olarak kullanılmayan 14-15V PMOS içindir ve en çok kullanılan tür, 5 volt TTL veya ve bu önemlidir, 5 volt CMOS içindir. Darlington'ları 3. (07:41) 3 volt ile açabilirsiniz, bu kadar. Yani, bir mikrodenetleyici çıkışına sahipseniz ve çıkış yüksek olduğunda 3.3 volt veriyorsa, 2803A evrensel tip kullanıyorsanız bu çıkışları güvenle açabilir. Ancak günümüzde hala standart CMOS kullanılmaktadır çünkü standart CMOS, 15 ya da bazı IC'lerin 18 volta kadar çıkabilen voltajlarını destekleyebilmektedir. Bu, bazı analog veya dijital devrelerde oldukça kullanışlı olabilir ve eğer 6 volt üzerinde VCC ile çalışan CMOS kullanıyorsanız, akkor ULN 2804A'yı kullanmanız gerekmektedir. (08:41) ULN 2804A, çünkü farklı bir taban direncine sahiptir; aksi takdirde, yüksek çıkışlı CMOS'tan bir taban akımı çok fazla olur ve bu, CMOS'u çekerek devre dışı bırakır ve standart CMOS ile normalde izin verilen akımdan daha yüksek bir taban akımı çeker. Ve son olarak, 2805, yüksek çıkışlı TTL için tasarlanmıştır. Yani, 2804A için, özellikle yüksek voltaj CMOS veya PMOS kullanıyorsanız, eğer hala PMOS ile çalışan herhangi bir IC'ye sahipseniz, bunu kullanmalısınız. (09:41) En çok kullanılan tür, yani, 5 volt evrensel türdür. Bu, esasen tüm 3.3 ila 5 volt dijital çıkışlara bağlanabilir, bu yükse TTL veya CMOS olsun. En çok kullanılan iki tür, 5 volt evrensel tür ve yüksek voltaj CMOS veya u PMOS için 2804'tür. Şimdi data sheet'e daha yakından bakalım. Çıkış voltajı 50 volt'tur, 500 miliamper maksimum sürekli kolektör akımı elde edilebilir, ancak ayrıca dikkate alınması gereken, kolektör-emiter doyurma voltajı 1.3 volt kadar yüksek olabilir, en kötü durumda 1.6 volt olabilir. Yani, sadece 5 voltluk bir güç kaynağı kullanıyorsanız ve bir çıkışta 500 miliamper anahtarlıyorsanız, (11:16) kolektör-emiter'de 1.6 volt kadar olabilir. Bu yüzden kalan sadece 3.4 volt kalır ve yükünüz de bu kaybı dikkate alarak güvenli bir şekilde çalışmalıdır. Sonraki, açma ve kapatma gecikme süresidir. Bir mikrosaniyenin dörtte biri ya da 250 nanosaniye ile bakıldığında hızlı görünebilir ama bugünlerde hızlı mikrodenetleyicilerle, büyük LED matrislerini çoklayarak anahtarlıyorsanız problem yaşayabilirsiniz. Bu bile Arduino ile çalışırken 60 megahertz frekansı ile 250 nanosaniyelik bir açma-kapatma gecikmesi dikkate alınmalıdır. (12:08) Bu şekilde, bir çıkışın kapanması ve diğerinin açılması arasındaki zamanda çakışma yaşamazsınız ve böylece iki çıkışın aynı anda aktığını fark etmezsiniz. Son olarak, gerçek çıkış akımına bakalım. Maksimum çıkış akımı 500 miliamperdir ama önerilen maksimum akım sadece 400 miliamperdir. Bu da, kaç çıkışı aynı anda kullanacağınıza bağlıdır. Yani, sekiz çıkış aynı anda açılacaksa ve 500 miliamper verecekse, bu mümkün değildir. Düşük voltaj 100% duty cycle ile her biri 150 miliamper verebilir, toplamda, sekiz çıkışın toplamı 1.2 amper olabilir. (14:00) Ama sadece iki çıkış yüzde yüz duty cycle ile 400 miliamper verebiliri. Yani toplam 400 miliamper / toplam 2 çıkış, yani sürekli açık iki çıkış 400 miliamper sağlayabilir. Ama eğer zamanla sadece bir çıkışı açık tutuyorsanız ya da çokluyorsanız, bu durumda gerçekten 400 miliamper sağlayabilirsiniz. Yani, sekiz çıkış da açılacaksa ve sadece bir dönem% 28'inde açık olacaksa. Bu durumda gerçekten sekiz çıkıştan 400 miliamper sağlayabilirsiniz, ancak sadece döneminin yüzde 28'i boyunca. (15:03) Yani, sürekli açık kalırlarsa devrenizi yok etmeyecek, dikkat etmelisiniz. Yani, güvenilir bir güç devresi inşa etmek için bu dikkate alınmalıdır. Son olarak, sizinle ULN 2000 düşük taraf ve 29 8 yüksek taraf sürücüleri hakkında bilgi paylaşacağım. Farklılıklar, belirli lojik aileler için Farklı numaralandırma yine farklı lojik aileler için. Bunu yüksek taraf sürücüleri veya sürücülerin Yüksek bir voltajla yük edilmiş olması anlamına gelir, yüklerin ortak bir toprak bağlantısı olabilir. Bu bazen VFD (vakum floresan ekran) ekranları VFD kullanımı güç kaynağıdır. İç yapı biraz daha karmaşık olabilir, (16:52) özellikle VFD (vakum floresan ekran) ekranları. Bu nedenle geçiş anahtarlama yapmak için çok uygun olduğundan. İç yapı biraz daha karmaşık olabilir, IC üreticileri için güç NPN transistör yapı daha kolaydır. Bir NPN transistör ve yalnızca bir PNP transistör olduğunu göreceksiniz. Yüksek taraf sürücüleri oluşturmak için biraz çaba sarf edilmelidir. Burada toplama yapan bir bağlantı ve çıkış buradadır. Bu durumda, pozitif güç kaynağı yükü yüksek taraftan düşük tarafa geçer. Düşük taraf, burada doğru yine akış termal yük ) içerir. Burada yön, burada yön ile pozitif güç kaynağı ortak bir bağlantıya ve yük çıkışıdır iç tasarımından dolayı. (17:43) ve burada serbest döner diyot. 80 volt, ULN 2800 x düşük taraf sürücüsü. Ancak, 35 volta kadar çalışabilir voltaj sürücüsü olarak kullanılabilir ve günlük işçiyi kendi biraz örneği kullanarak IC kullanımı ve alçak bir şekilde kullanma veya ilgili VFD ve diyot konumları. (18:43) Yüksek bir voltaj daha kullanabilirsiniz ancak 35 volt. IC var olanım ve bu bir çok silikon veya diskret transistörleri kullanılırken sağlarda doğru yapılaş durumda burada ve uygulaması. Tekrar teşekkürler Kulağınıza takıldığınız bilgilere yönelik IC UDLN 2008 OX düşük yan ve 29 8X yüksek yan 200 olarak size daha bilgiye sahip oldun. Teşekkürler. Bird, benden raja'den crane'e.

  3. User

    How does a BMS (Battery Management System) work? | Passive & Active cell balancing Explained - YouTube https://www.youtube.com/watch?v=q4wDa_m9-8E

    Transcript: (00:01) Hey guys, last time we saw why we need a BMS and what it does? This time we will see what is a BMS made of? and how does it work? Without wasting any time, buckle up and let's go for a ride. A battery management system is made of many hardware and software functional blocks which has: cutoff MOSFETs, fuel gauge monitor Cell voltage monitor / Cell voltage balancing circuit real-time clock (RTC) and temperature monitor system Now let’s take a look at the purpose and the technology behind each block Cutoff FETs- (00:56) These are basically transistors, mostly MOSFETs are used, MOSFETs are nothing but controlled switches. These are used for connection and isolation of the battery pack between the load and charger. MCU of the BMS measures the cell voltages, current in real-time and based on that it Switches these FETs.These can be configured in 2 types. (01:24) Here it has a single connection to the Charger and load in our case motor controller and Motor. 2nd diagram has 2 different connections for the Charger and Load. Generally 1st configuration is used in the BMS system, because it reduces the hardware where just one bus controls the charging and discharging. (01:55) Initially both MOSFETs are turned off, when a charger is connected, the current is not flowing because FETs are off. BMS senses voltage at the input and then it turns on the CFET which charges the battery. If the voltage at the input pin is not present then BMS determines that Motor is Connected then it turns on the DFET. (02:26) fuel gauge / current monitor- This block keeps the track of the charge coming in and going out of the battery pack. Charge is the product of current and time. For measuring the current, a current sense amplifier and a MCU which has an Analog to digital converter is used. A very low value current sense resistor is connected in series with the battery line, voltage drop across this resistor is measured by this amplifier then it amplifies the signal and delivers it to the ADC of the microcontroller. (03:00) The microcontroller measures the voltage and calculates the charge according to time. The discharging and charging current is sensed by the direction of current, if the current is going out of the battery then battery is discharging and if the current coming inside of the battery that means the battery is charging or there are certain fuel gauge ICs are available in the market, which takes care of SOC and SOH estimation of the battery. (03:30) Many times using a fuel gauge IC adds additional cost to the BMS design and when the load current is erratic as in Electric vehicle case, using a shunt resistor is always the best option. This configuration also helps for overcurrent protection, when current rises above safety level, the fuel gauge circuit senses it and gives the signal to turn off the DFET or CFET. (03:59) Cell voltage monitoring / cell balancing - Monitoring the voltage of each cell is very important. Generally, Li-Ion batteries are used in EVs, the voltage of a Li-ion cell ranges from 2.5V- 4.2V and it depends on the chemistry. As we saw last time, operating the battery outside the voltage range significantly reduces the lifetime of the cell. (04:26) These cells are connected in series and parallel combination to form a battery pack. When cells are connected in parallel combination it increases the current of the battery pack, while a series connection increases the overall voltage. Even if the cells are created by the same manufacturer and in the same lot, physical properties such as internal resistance, the nominal voltage and temperature imbalance will slightly differ from each other, while charging and discharging not every cell behaves the same. (04:47) While charging, If the battery pack has a weaker cells than an average cell, this would result in the weakest cell to reach out it’s limit first and the rest of the cells are still charging, so this weaker cell heats up and its lifespan decays,on the other hand, a weaker cell discharges faster than rest of the cells. (05:11) The weaker cell trips the discharge limit first leaving the rest of the cells with some charge remaining inside of them. This can be overcome by cell balancing, This cell balancing is derived into 2 parts Passive balancing Active balancing Lets see the passive balancing - It is the simplest and cost effective method. (05:37) In this method a dummy load like a resistor is used to discharge the excess voltage and equalize it with other cells. These resistors are known as bypass resistors. Each cell connected in series in a pack will have its own bypass resistor connected through a switch. While charging the weaker cell charges very fast so the MOSFET connected across the weaker cell is turned on, the charge of this cell is removed and dissipated through this resistor, this process minimizes the charging rate of the weaker cell, whenever charge level of (06:15) the weak cell tends to go near to its full capacity the MOSFET is turned on, so all cells along with weaker cell charges at the same time but this method is not useful while discharging the weaker cell may reach to its minimum cut off voltage earlier than the other cell This balancing technique is inexpensive and technically easy to implement, but is not very efficient because electrical energy is dissipated as heat in the resistors and FET also has switching losses. (06:52) Another drawback is that the entire discharge current flows through the MOSFET which is mostly built into the controller IC and hence the discharge current has to be limited to lower value upto the ICs limits which increases the discharging time. Active balancing Unlike Passive balancing, in active balancing the excess charge from one cell is transferred to another cell which has low charge to equalize them. (07:33) So this can be done by charge storing components like Capacitors and Inductors. Well, there are many methods to perform an Active cell balancing. Let's discuss the method which is commonly used. The Charge Shuttles / Flying Capacitors is the most commonly used method in the active balancing, In this the capacitors are used to transfer the charge from high voltage cell to low voltage cell. (08:00) The capacitor is connected through SPDT switches, initially the switch connects the capacitor to the cell which has high voltage and once the capacitor is charged then the switch connects it to the cell which has lower voltage and the charge from the capacitor flows into the cell. These capacitors are called the flying capacitors. (08:25) Well, the problem with this method is that the charge can be transferred only between adjacent cells. Also it takes more time because the capacitor has to be charged and then discharged to transfer the charges, but still it is better than passive balancing. Just like this there are many active cell balancing techniques, which are out of the scope of this video (ref) (ref) 3. (08:46) Next important parameter is Temperature Monitoring - Li-ion batteries provide a lot of current while maintaining a constant voltage, which can lead to a thermal runaway condition that causes the battery to catch fire. The construction of a battery is highly volatile. Well, this temperature measurement is not just for safety, it can also suggest if the temperature of the battery is suitable for charging or not. (09:16) To measure the temperature of these batteries a temperature sensor is used, generally the thermistors are used as a temperature sensor, the thermistor is basically a temperature dependent resistance, whenever there is change in temperature the resistance of the thermistor changes and BMS calculates the temperature rise accordingly. (09:39) As we saw in the last video, the BMS acts as a logbook, to calculate the SOH and other parameters of the battery so for that purpose the BMS has to take the data according to time, so it should be working even if the vehicle is not on, but it might consume the excessive power from the battery pack itself, so. (10:06) to avoid that a Real time clock is integrated with the BMS which needs very small power, and it does our job. (Ref) Well that’s all about the BMS of an Electric vehicle, if you think there is something missing please let me know in the comment section. Hit the like button if you liked this video, subscribe to my channel and finally, thanks for watching.bu yazının hepsini türkçeye çevir

  4. Assistant

    Tabii, işte verilen metnin tamamının Türkçeye çevrilmiş hali:

    (00:01) Merhaba arkadaşlar, geçen sefer BMS'ye neden ihtiyaç duyduğumuzu ve neler yaptığını gördük. Bu sefer bir BMS'nin nelerden oluştuğunu ve nasıl çalıştığını göreceğiz. Hiç vakit kaybetmeden, kemerlerinizi bağlayın ve bir yolculuğa çıkalım. Bir batarya yönetim sistemi, kesme MOSFET'leri, yakıt göstergesi monitörü, hücre voltaj monitörü/hücre voltaj dengeleme devresi, gerçek zamanlı saat (RTC) ve sıcaklık monitörü sistemi gibi birçok donanım ve yazılım işlevsel bloğundan oluşur. Şimdi her bloğun amacına ve teknolojisine bir bakalım. Kesme FET'leri- Bunlar aslında transistörlerdir, çoğunlukla MOSFET'ler kullanılır, MOSFET'ler kontrol edilen anahtarlardan başka bir şey değildir. Bunlar, batarya paketinin yük ve şarj cihazı arasındaki bağlantı ve izolasyonu için kullanılır. BMS'nin MCU'su hücre voltajlarını, akımı gerçek zamanlı olarak ölçer ve buna dayanarak bu FET'leri anahtarlar. Bunlar iki türde yapılandırılabilir.

    (01:24) Burada, şarj cihazı ve tam olarak bizim durumumuzda motor kontrolörü ve motor için tek bir bağlantı vardır. İkinci diyagramda şarj cihazı ve yük için iki farklı bağlantı vardır. Genellikle birinci yapılandırma BMS sisteminde kullanılır çünkü sadece bir hatla şarj etme ve deşarj işlemlerini kontrol ederek donanımı azaltır.

    (01:55) Başlangıçta her iki MOSFET de kapalıdır, bir şarj cihazı bağlandığında, FET'ler kapalı olduğundan akım akmaz. BMS, girişte voltajı algılar ve ardından bataryayı şarj eden CFET'i açar. Giriş pininde voltaj yoksa, BMS motorun bağlı olduğunu belirler ve ardından DFET'i açar.

    (02:26) Yakıt göstergesi/akım monitörü- Bu blok, batarya paketine girip çıkan şarjı takip eder. Şarj, akım ve zamanın çarpımıdır. Akımı ölçmek için bir akım algı amplifikatörü ve bir Analog dijital çevirici (ADC) bulunan bir MCU kullanılır. Çok düşük değerli bir akım algı direnci batarya hattına seri olarak bağlanır, bu direncin üzerindeki voltaj düşüşü amplifikatör tarafından ölçülür, daha sonra bu sinyali yükseltir ve mikrodenetleyicinin ADC'sine iletir.

    (03:00) Mikrodenetleyici voltajı ölçer ve zamana göre şarjı hesaplar. Deşarj ve şarj akımı, akımın yönüne göre algılanır; eğer akım bataryadan çıkıyorsa batarya deşarj oluyor demektir, eğer bataryaya giriyorsa batarya şarj oluyor demektir ya da bazı yakıt göstergesi IC'leri piyasada mevcuttur, bu IC'ler bataryanın SOC ve SOH tahmini ile ilgilenir.

    (03:30) Birçok kez, bir yakıt göstergesi IC kullanmak, BMS tasarımına ek maliyet katmaktadır ve yük akımı düzensiz olduğunda, örneğin elektrikli araç durumunda, bir şönt direnci kullanmak her zaman en iyi seçenektir. Bu yapılandırma ayrıca aşırı akım korumasına da yardımcı olur, akım güvenlik seviyesinin üzerine çıktığında, yakıt göstergesi devresi bunu algılar ve DFET veya CFET'i kapatma sinyali verir.

    (03:59) Hücre voltaj izleme/hücre dengeleme - Her hücrenin voltajını izlemek çok önemlidir. Genellikle elektrikli araçlarda Li-ion bataryalar kullanılır ve bir Li-ion hücresinin voltajı 2.5V-4.2V arasında değişir ve bu kimyaya bağlıdır. Geçen sefer gördüğümüz gibi, bataryayı voltaj aralığının dışında çalıştırmak hücrenin ömrünü önemli ölçüde azaltır.

    (04:26) Bu hücreler bir batarya paketi oluşturmak için seri ve paralel kombinasyonlarla bağlanır. Hücreler paralel kombinasyonla bağlandığında, batarya paketinin akımını artırır, seri bağlantı ise toplam voltajı artırır. Hücreler aynı üretici tarafından aynı parti içinde üretilmiş olsa bile, iç direnç, nominal voltaj ve sıcaklık dengesizliği gibi fiziksel özellikler birbirinden biraz farklı olacaktır, şarj ve deşarj sırasında her hücre aynı şekilde davranmaz.

    (04:47) Şarj sırasında, batarya paketinde zayıf bir hücre varsa, bu, en zayıf hücrenin önce sınırına ulaşmasına ve diğer hücrelerin hala şarj olmasına neden olur, bu yüzden bu zayıf hücre ısınır ve ömrü azalır; diğer yandan, zayıf bir hücre diğer hücrelerden daha hızlı deşarj olur.

    (05:11) Zayıf hücre, diğer hücrelerde hala biraz şarj kalmışken önce deşarj sınırını aşar. Bu hücre dengeleme ile aşılabilir, bu hücre dengeleme iki türe ayrılır: Pasif dengeleme ve Aktif dengeleme. Şimdi pasif dengelemeyi görelim - Bu en basit ve maliyet etkin yöntemdir.

    (05:37) Bu yöntemde, bir direnç gibi sahte bir yük kullanılır ve fazla voltajı deşarj edip diğer hücrelerle eşitlenir. Bu dirençlere bypass dirençleri denir. Pakette seri olarak bağlanan her hücre, bir anahtar aracılığıyla bağlı kendi bypass direncine sahiptir. Şarj sırasında, zayıf hücre çok hızlı şarj olur, böylece zayıf hücrenin bağlı olduğu MOSFET açılır, bu hücrenin şarjı alınır ve bu direnç yoluyla dağıtılır, bu işlem zayıf hücrenin şarj oranını minimize eder, zayıf hücrenin şarj seviyesi tam kapasitesine yaklaştığında MOSFET açılır, böylece tüm hücreler ve zayıf hücre aynı anda şarj olur ancak bu yöntem deşarj sırasında işe yaramaz.

    (06:15) zayıf hücre diğer hücreden daha erken minimum kesme voltajına ulaşabilir. Bu dengeleme tekniği ekonomiktir ve teknik olarak uygulaması kolaydır, ancak çok verimli değildir çünkü elektrik enerjisi dirençlerde ve FET'in anahtarlama kayıplarında ısı olarak dağılır.

    (06:52) Başka bir dezavantaj da, tüm deşarj akımının genellikle kontrolör IC'ye entegre edilen MOSFET aracılığıyla akmasıdır, bu nedenle deşarj akımı IC'nin limitlerine kadar sınırlı olmalıdır, bu da deşarj süresini artırır. Aktif dengeleme - Pasif dengelemenin aksine, aktif dengelemede bir hücreden fazla şarj diğer düşük şarja sahip bir hücreye aktarılır, böylece eşitlenir.

    (07:33) Bu, kapasitörler ve indüktörler gibi şarj depolama bileşenleri ile yapılabilir. İyi, aktive hücre dengeleme işlemini gerçekleştirmek için birçok yöntem var. En yaygın olarak kullanılan yöntemi tartışalım. Şarj Shuttle'ları / Uçan Kapasitörler en yaygın olarak kullanılan yöntemdir, bu yöntemde kapasitörler yüksek voltajlı hücreden düşük voltajlı hücreye şarj aktarımı için kullanılır.

    (08:00) Kapasitör, SPDT anahtarları aracılığıyla bağlanır, başlangıçta anahtar kapasitörü yüksek voltajlı hücreye bağlar ve kapasitör şarj olduktan sonra anahtar onu daha düşük voltajlı hücreye bağlar ve kapasitörden hücreye şarj akışı olur. Bu kapasitörlere uçan kapasitörler denir.

    (08:25) İyi, bu yöntemdeki problem, şarj sadece bitişik hücreler arasında aktarılabilir. Ayrıca çünkü kapasitörün şarj edilmesi ve ardından şarjı aktarmak için deşarj edilmesi gerektiğinden daha uzun sürer, fakat yine de pasif dengelemeden daha iyidir. Bunun gibi birçok aktif hücre dengeleme tekniği var, ki bu video için kapsam dışıdır.

    (08:46) Sıradaki önemli parametre Sıcaklık İzleme - Li-ion bataryalar sabit bir voltajı korurken çok fazla akım sağlar, bu da bataryanın yangın çıkaracak bir termal koşuya neden olabilir. Bir bataryanın yapısı oldukça değişkendir. İyi, bu sıcaklık ölçümü sadece güvenlik için değil, aynı zamanda bataryanın düşük şarj için uygun olup olmadığını gösterebilir veya gösterebilir. (09:16) Bu bataryaların sıcaklığını ölçmek için bir sıcaklık sensörü kullanılır, genellikle termistörler sıcaklık sensörü olarak kullanılır, termistör esasen sıcaklık bağımlı bir dirençtir, sıcaklık değiştiğinde termistörün direnci de değişir ve BMS sıcaklık artışını buna göre hesaplar. (09:39) Son videoda gördüğümüz gibi, BMS, bataryanın SOH ve diğer parametrelerini hesaplamak için bir kütük kitabı olarak hareket eder, bu nedenle BMS'nin verileri zamana göre alması gerekir, bu nedenle araç açık olmasa bile çalışmalıdır, ancak aynı zamanda batarya paketinden aşırı güç tüketebilir. (10:06) Bunu önlemek için bir Gerçek Zamanlı Saat BMS'ye entegre edilmiştir ve bu çok az güç ihtiyaç duyar ve işimizi yapar. İyi, bu Elektrikli araç BMS hakkında her şey, eğer eksik bir şey olduğunu düşünüyorsanız lütfen yorum bölümünde bana bildirin. Bu videoyu beğendiyseniz beğen butonuna basın, kanalına abone olun ve sonunda, izlediğiniz için teşekkürler.