Skip to content
The Chat Archive
gpt-4o-2024-05-13· OpenAI WildChat-4.8M (AI2)

P8B75-M LX PLUS wake on lan setting

  1. User

    P8B75-M LX PLUS wake on lan setting

  2. Assistant

    To enable Wake on LAN (WoL) on the ASUS P8B75-M LX PLUS motherboard, you typically need to configure settings both in the BIOS and within your operating system. Here’s a step-by-step guide to help you do that:

    Step 1: Configure BIOS Settings

    1. Power on your PC and press the DEL key (or F2 in some cases) immediately when the ASUS logo appears to enter the BIOS setup.

    2. Navigate to the "Advanced" tab using the arrow keys.

    3. Go to “APM Configuration” (Advanced Power Management).

    4. Look for an option called “Power On by PCI/PCI-E Device” or something similar, and change it to Enabled.

    5. If there is an option for “Wake on LAN” directly, make sure it is set to Enabled.

    6. Navigate to the “Boot” tab and ensure that any settings related to booting after power loss are set according to your preferences.

    7. Save your changes and exit the BIOS setup. This is usually done by pressing F10 and confirming with Enter.

    Step 2: Configure Operating System Settings

    For Windows:

    1. Open Device Manager: Press Windows + X and select Device Manager.

    2. Expand the “Network adapters” section and find your network adapter. Right-click on it and select “Properties”.

    3. Go to the “Power Management” tab.

    4. Make sure the options “Allow this device to wake the computer” and “Allow only a magic packet to wake the computer” are checked.

    5. Click OK to save your changes.

    Configuring Additional Settings in Windows:

    1. Network and Sharing Center: Go to Control Panel > Network and Sharing Center > Change adapter settings.

    2. Right-click on the active network adapter and select “Properties”.

    3. Click on “Configure” next to the network adapter.

    4. Go to the “Advanced” tab.

    5. Enable any settings related to “Wake on Magic Packet”, “Wake on pattern match”, or any similar wake on LAN settings.

    For Linux:

    1. Check if ethtool is installed. If not, install it using your package manager, for example, sudo apt-get install ethtool.

    2. Use the following command to check and enable WOL:

      sudo ethtool <interface>
      

      Replace <interface> with your network interface name (e.g., eth0).

    3. To enable WOL, use:

      sudo ethtool -s <interface> wol g
      
    4. To make this setting persistent across reboots, you might need to add this command to your network configuration scripts or a startup script.

    Step 3: Test Wake on LAN

    To test Wake on LAN, you'll need another device that can send the magic packet to wake up your system. Numerous tools and apps can do this. For example:

    • For Windows: Use apps like WakeMeOnLan.
    • For Mobile: Use mobile apps like "Wake On Lan" available on both Android and iOS.

    Input the MAC address of the target machine's network card and send the magic packet. If everything is configured correctly, the system should power on.

    Remember, for Wake on LAN to work, the PC has to be in a state where it can receive network packets (typically Sleep, Hibernate, or Soft Off). Make sure it’s not completely powered off unless your motherboard and network interface support waking from a completely powered-off state.

  3. User

    P8B75-M LX PLUS wake on lan setting with ubuntu

  4. Assistant

    To set up Wake on LAN (WoL) on the ASUS P8B75-M LX PLUS motherboard with Ubuntu, you need to configure settings both in the BIOS and within your operating system. Here is a step-by-step guide for activating WoL on Ubuntu.

    Step 1: Configure BIOS Settings

    1. Power on your PC and press the DEL key (or F2) immediately when the ASUS logo appears to enter the BIOS setup.

    2. Navigate to the "Advanced" tab using the arrow keys.

    3. Go to “APM Configuration” (Advanced Power Management).

    4. Locate the “Power On by PCI/PCI-E Device” option and set it to Enabled.

    5. If there is an option for “Wake on LAN”, make sure it's set to Enabled as well.

    6. Save your changes and exit the BIOS: F10 and then confirm with Enter.

    Step 2: Configure Ubuntu for Wake on LAN

    1. Install ethtool

    First, you need to ensure that ethtool is installed. ethtool is a utility for querying and changing network device driver and hardware settings, particularly for enabling WoL features.

    sudo apt-get update
    sudo apt-get install ethtool
    

    2. Enable Wake on LAN

    Identify your network interface (often eth0, but it may differ).

    ifconfig
    

    or

    ip a
    

    You will see something like eth0, eno1, or enp3s0. Use the correct interface name in place of <interface> in the following commands.

    Check if WoL is supported and enabled:

    sudo ethtool <interface>
    

    You should see something like:

    Supports Wake-on: pumbg
    Wake-on: g
    

    g indicates that Wake-on-LAN is enabled. If it is not, enable it by:

    sudo ethtool -s <interface> wol g
    

    3. Make the WoL Setting Persistent Across Reboots

    Add the ethtool command to a startup script to ensure it remains enabled after a reboot.

    Create a new startup script:

    sudo nano /etc/network/if-up.d/wol
    

    Add the following lines to the script:

    #!/bin/sh
    ethtool -s <interface> wol g
    

    Replace <interface> with your network interface name.

    Save and close the file (Ctrl + X, then Y, then Enter).

    Make the script executable:

    sudo chmod +x /etc/network/if-up.d/wol
    

    4. Verify Your Script

    Restart your network service or reboot your computer:

    sudo systemctl restart networking.service
    

    or

    sudo reboot
    

    After rebooting, check the WoL setting again to ensure it is still enabled:

    sudo ethtool <interface>
    

    Step 3: Test Wake on LAN

    To test Wake on LAN, you'll need another device that can send a magic packet to wake up your system. Here are a few tools:

    • Windows: You can use programs like WakeMeOnLan.

    • Linux/Ubuntu: You can use the wakeonlan utility. Install it if not already installed:

      sudo apt-get install wakeonlan
      

      Then send a magic packet to your PC's MAC address:

      wakeonlan <MAC_ADDRESS>
      

    Additional Tips

    • Ensure that the Ubuntu machine is in a sleep state (S3), hibernate, or soft-off state. Completely shutting down might not always work unless the motherboard supports it.
    • Ensure that your network interface remains powered in the target state for WoL to work.

    By following these steps, you should be able to configure and test Wake on LAN successfully on your ASUS P8B75-M LX PLUS motherboard running Ubuntu.