Skip to content
TheChatArchiveThe Chat Archive
gpt-4-turbo-2024-04-09· OpenAIAi2 WildChat-4.8M (AI2)

vnc ubuntu with novnc websockify and x11vnc

  1. User

    vnc ubuntu with novnc websockify and x11vnc

  2. Assistant

    Setting up VNC on Ubuntu with noVNC, websockify, and x11vnc involves several steps. This setup enables you to access your Ubuntu desktop remotely through a web browser using VNC technology. I'll guide you through the process of installing and configuring these tools.

    Step 1: Install Prerequisites

    Before you start, make sure your Ubuntu system is updated:

    sudo apt update
    sudo apt upgrade
    

    Step 2: Install x11vnc

    x11vnc is a VNC server that allows you to access the actual display that has been logged in interactively. Install x11vnc using the following command:

    sudo apt install x11vnc
    

    Create a password for VNC connections to make sure the connection is secure:

    x11vnc -storepasswd
    

    This command will prompt you to enter a password and store it in the default location (~/.vnc/passwd).

    Step 3: Install noVNC and websockify

    noVNC is a HTML5 VNC client that runs in a web browser. websockify is a WebSocket to TCP proxy/bridge, which enables noVNC to connect with the VNC server.

    sudo apt install novnc websockify
    

    Step 4: Configure websockify to Connect with x11vnc

    Use websockify to create a bridge between the web (WebSocket protocol) and the x11vnc server (VNC protocol). The noVNC client will connect through websockify.

    Run websockify to forward WebSocket connections to the x11vnc server. We will use port 6080 for the WebSocket:

    websockify -D --web=/usr/share/novnc/ 6080 localhost:5900
    

    This command also sets the noVNC files to be served directly so that you can connect using a browser.

    Step 5: Start x11vnc Server

    You can start the x11vnc server with the password you configured earlier:

    x11vnc -forever -usepw -display :0
    
    • The -forever flag keeps x11vnc running if a client disconnects.
    • The -usepw flag tells x11vnc to use the stored password.
    • The -display :0 targets the display number (generally, :0 for the primary display).

    Step 6: Access from the Browser

    Now you can access your Ubuntu desktop from a browser on another machine. Open a browser and enter:

    http://<your-ubuntu-machine-ip>:6080/vnc.html
    

    Step 7: Secure the Setup (Optional)

    If accessing over the public internet, it is highly recommended to secure the connection. You can do this by setting up an HTTPS connection with a reverse proxy like Nginx or Apache.

    Additional Tips

    • Set both x11vnc and websockify to start automatically after a reboot for uninterrupted access.
    • Consider setting up a firewall and opening only the necessary ports to increase security.

    Step 8: Troubleshooting

    If you encounter any issues:

    • Check firewall settings to make sure the appropriate ports (6080 for websockify, 5900 for x11vnc) are open.
    • Verify the status of x11vnc and websockify services.
    • Ensure your browser supports HTML5.

    This should give you a basic, functional setup for accessing Ubuntu via VNC through a web browser. Adjust configurations and settings based on your specific needs and network environment.

  3. User

    how about ufw setting?

  4. Assistant

    When using Ubuntu and setting up remote services like VNC, it's crucial to ensure that security is maintained. One fundamental aspect of this is managing the firewall rules. Ubuntu comes with ufw (Uncomplicated Firewall), which simplifies the process of configuring iptables, the default firewall software on Ubuntu.

    To make your VNC setup accessible while maintaining security, you'll need to allow the necessary ports through the firewall. Here's how you can do it for the setup mentioned previously:

    Step 1: Check ufw Status

    Before making any changes, check whether ufw is active:

    sudo ufw status verbose
    

    Step 2: Allow VNC Ports

    As described in the setup, x11vnc will communicate over port 5900 by default, and websockify is bridging this to port 6080 for noVNC. You need to allow these ports through the firewall:

    Allow traffic on port 6080:

    sudo ufw allow 6080/tcp comment 'allow noVNC web interface'
    

    Although it's only necessary to have web access via port 6080 for noVNC to function (as it's proxying to port 5900), you might want to directly access x11vnc for some other clients or purposes. In that case, also allow port 5900:

    sudo ufw allow 5900/tcp comment 'allow VNC'
    

    Step 3: Enable ufw

    If ufw is not enabled, turn it on. Note that enabling ufw when not configured properly might block your current SSH connection, if any. Always ensure you understand the active rules before enabling the firewall.

    sudo ufw enable
    

    This command will ask for confirmation, review the active rules (again by sudo ufw status verbose), and if you're sure they're correct, proceed to activate ufw.

    Step 4: Verify the Rules

    After enabling and configuring the firewall, check your settings:

    sudo ufw status
    

    This shows all active rules and their associated comments. Verify that ports 6080 and possibly 5900 are allowed from the desired locations.

    Additional Recommendations:

    • Limit Access: If you know the IP addresses or IP range of the devices that will connect to the noVNC service, you can restrict access to only those IPs for better security. For example:

      sudo ufw allow from 192.168.1.0/24 to any port 6080 proto tcp comment 'allow noVNC from local network'
      
    • Logging: Enabling logging can help monitor and troubleshoot issues related to firewall:

      sudo ufw logging on
      
    • Managing Rules: If at any point, you need to delete a rule, use the numbering system shown with ufw status numbered and then sudo ufw delete [number].

    Conclusion

    Configuring ufw properly is a safety-critical aspect especially when exposing services to the network. Always ensure you have appropriate rules in place that balance accessibility and security.

  5. User

    websockify with ssl setting

  6. Assistant

    When setting up websockify to use SSL in order to secure the communication between the client's browser and the noVNC service, you will need a valid SSL certificate. This could be from a trusted Certificate Authority (CA) or a self-signed certificate if you are just testing or using it in a private network. Here's how you can set up websockify with SSL:

    Step 1: Obtain or Generate SSL Certificate

    Using Let's Encrypt (Trusted CA)

    If your server is publicly accessible with a domain name, you can use Let's Encrypt to obtain a free trusted SSL certificate. Install Certbot and obtain a certificate:

    sudo apt install certbot
    sudo certbot certonly --standalone --preferred-challenges http -d your-domain.com
    

    Replace your-domain.com with your actual domain. Certbot will save the certificate and key files at /etc/letsencrypt/live/your-domain.com/.

    Create a Self-Signed Certificate

    For private or testing purposes, you can generate a self-signed certificate:

    mkdir ~/certs
    openssl req -new -x509 -days 365 -nodes -out ~/certs/novnc.pem -keyout ~/certs/novnc.pem
    

    This command creates a new certificate and private key in one file (novnc.pem) under ~/certs/. When generating, you'll be prompted for some details; fill them as needed or leave them blank for defaults.

    Step 2: Configure websockify to Use SSL

    Once you have your certificate, you need to start websockify with the SSL options. You can use the following command (modify paths as necessary depending on where your certificate is stored):

    For a certificate from Let's Encrypt:

    websockify --cert=/etc/letsencrypt/live/your-domain.com/fullchain.pem --key=/etc/letsencrypt/live/your-domain.com/privkey.pem -D 6080 localhost:5900
    

    Or, if using the self-signed certificate:

    websockify --cert=~/certs/novnc.pem --key=~/certs/novnc.pem -D 6080 localhost:5900
    

    These commands start websockify in daemon mode (-D), listening on port 6080 for encrypted WebSocket connections and proxying them to the local VNC server running on port 5900.

    Step 3: Access noVNC with HTTPS

    You can now access noVNC over a secure connection. If websockify is running with SSL and serving static files from the noVNC directory, navigate to:

    https://your-domain.com:6080/vnc.html
    

    Replace your-domain.com with your actual domain or IP address. Because you're using a self-signed certificate, you might need to accept security warnings in your browser.

    Step 4: Secure Your System

    • Ensure all firewall settings are correct (only allow HTTPS traffic on port 6080, and if needed, VNC traffic on port 5900).
    • Regularly update your SSL certificates (especially important if using certificates from Let's Encrypt, which have a 90-day validity).

    Additional Consideration

    If you're setting this up in a production environment or exposing it to the internet, it's wise to consider adding additional layers of security, such as HTTP basic auth or an IP whitelist, and to use a reverse proxy like Nginx or Apache for even better control and security. Furthermore, always keep your system and respective packages up to date.

  7. User

    websockify OSError: [Errno 98] Address already in use

  8. Assistant

    The "Address already in use" error suggests that the port you're trying to use for websockify is already occupied by another process. This can happen if you have another instance of websockify already running, or if another application is using the same port. Here’s how you can resolve this issue:

    Step 1: Identify the Process Using the Port

    First, you need to find out what process is using the port that is giving you the error. Suppose the port is 6080, you can use the following command to find out:

    sudo netstat -plnt | grep 6080
    

    or use ss which is intended to replace netstat:

    sudo ss -plnt | grep 6080
    

    These commands will show which process is listening on port 6080. The output will include the PID (Process ID).

    Step 2: Kill the Process

    Once you have the PID, you can stop the process. If you decide that the process doesn’t need to be running, you can kill it with:

    sudo kill -9 <PID>
    

    Replace <PID> with the actual process ID you found. This command sends a SIGKILL signal, which immediately stops the process. Note that using -9 is forceful and should be used cautiously as it does not allow the process to terminate safely.

    Step 3: Restart websockify

    After you’ve freed up the port, you can try starting websockify again with your initial command.

    Step 4: Consider Alternative Approaches

    Change the port: If the port is required by another important service, you might consider configuring websockify to use a different port. For example:

    websockify --cert=/path/to/cert.pem --key=/path/to/key.pem -D 6081 localhost:5900
    

    Here, port 6081 is used instead of 6080.

    Check for duplicate services: If you’re frequently encountering this issue, make sure that your startup scripts or service configurations aren’t inadvertently attempting to start multiple instances of websockify.

    Step 5: Automate Port Checking

    To prevent this error in the future, you may implement a checking mechanism in your start-up script to check if the port is already in use before attempting to start websockify.

    Additional Notes

    • Always make sure to understand what processes are running and why before killing any processes. Stopping a critical system process can lead to system instability or downtime.
    • When possible, especially in production environments, consider configuring services to robustly handle such cases, including using mechanisms like systemd to manage service start and keep them in appropriate state if they crash or need to be restarted.

    By following these instructions, you should be able to resolve the "Address already in use" error and understand more about managing port conflicts on your system.

  9. User

    my command is "websockify --cert=/certs/novnc.pem --key=/certs/novnc.pem -D 6080 localhost:5901" but it said no cert file

  10. Assistant

    If websockify can't find the certificate file as specified with the --cert and --key options, it can mean several things: either the path is incorrect, the file doesn't exist, or there's a permissions issue preventing websockify from accessing the file. Here's how you can troubleshoot and resolve this issue:

    Step 1: Check the Existence of the File

    First, ensure that the certificate file actually exists at the specified location. Since you are using the ~ (tilde) in your command, which refers to the home directory of the current user, make sure there is a certs directory in your home folder containing novnc.pem.

    You can check this with:

    ls -l ~/certs/novnc.pem
    

    If the output indicates that the file does not exist, you'll need to ensure you're in the correct directory and that the file name is correct.

    Step 2: Use Absolute Paths

    It's a good practice to use absolute paths in your commands, especially in scripts, to avoid any ambiguity about file locations. Replace ~ with the full path to your home directory. For example:

    /home/username/certs/novnc.pem
    

    So, the revised command would be:

    websockify --cert=/home/username/certs/novnc.pem --key=/home/username/certs/novnc.pem -D 6080 localhost:5901
    

    Replace username with your actual username.

    Step 3: Correct Permissions

    Another common issue could be permissions-related. Ensure that the user running websockify has the necessary permissions to read the certificate and key files. Check permissions with:

    ls -l /home/username/certs/novnc.pem
    

    If the permissions are too restrictive, you might need to adjust them:

    chmod 644 /home/username/certs/novnc.pem
    

    This sets the file to be readable by all users (but only writable by the owner), which should suffice for most setups.

    Step 4: Running as the Correct User

    If the websockify command is executed as a user who doesn’t have access to your home directory (like a service user), then the user won’t be able to access the certificate file located in your home directory. Make sure that the command is being run as a user who has the appropriate permissions or consider moving the certificate to a more accessible location.

    Final Check

    After making these adjustments, try running the command again. If there are no errors, it should start successfully. If errors persist, re-check the paths, permissions, and user context under which the command is executed.

    By ensuring the correct path, permissions, and file existence, your websockify should be able to utilize the specified SSL certificates without issue.

  11. User

    what is --web=/usr/share/novnc/ mean

  12. Assistant

    The --web=/usr/share/novnc/ option used in the websockify command is a configuration setting that tells websockify where to find the static web files necessary for serving the noVNC client through the web browser. Essentially, it specifies the directory from which websockify serves the noVNC HTML, JavaScript, and other associated web files.

    Here's a breakdown of this option:

    --web

    • This is the option flag that tells websockify to also function as a simple web server.
    • It needs to be followed by the path to a directory containing the static files you want to serve.

    /usr/share/novnc/

    • This is the path where the noVNC client files are typically installed on a Linux system when noVNC is installed via package managers like apt.
    • This directory should contain files such as vnc.html (or vnc_lite.html), along with supporting JavaScript, CSS, and possibly other resource files needed to run the noVNC client in a browser.

    Usage Context

    When you use websockify with the --web option, websockify acts as a bridge between the WebSocket protocol, used by noVNC in the browser, and the normal TCP socket protocol, used by traditional VNC servers. By serving the noVNC static files, it allows you to access the VNC server simply by navigating to the URL of the websockify server in your browser (something like http://server-ip:port/vnc.html).

    This functionality is particularly useful because it simplifies client setup—users only need a modern web browser to connect to the VNC server without installing dedicated VNC client software.

    Example:

    If your websockify is running on a machine with the IP 192.168.1.100 and you've configured it to listen on port 6080, you would access your noVNC client through the following URL:

    http://192.168.1.100:6080/vnc.html
    

    When accessing this URL, the websockify server will serve the vnc.html file located in the /usr/share/novnc/ directory, along with any required static resources stored in that directory.

    This setup ensures that users can remotely access their VNC server securely and conveniently through their web browsers. Always make sure the directory path given to the --web option is correct and contains all the necessary noVNC client files.

  13. User

    how to only allow HTTPS traffic on port 6080

  14. Assistant

    To ensure that only HTTPS traffic is allowed on port 6080, and to secure your setup when using websockify with an SSL certificate for noVNC, you will need to ensure that the websockify command is properly configured to use SSL, and that your server's firewall only permits traffic on port 6080 for secure connections. Here are the steps you can follow:

    Step 1: Configure websockify with SSL

    As discussed before, ensure your websockify setup uses SSL by specifying the certificate and key files:

    websockify --cert=/path/to/your/certificate.pem --key=/path/to/your/privatekey.pem -D 6080 localhost:5900
    

    Replace /path/to/your/certificate.pem and /path/to/your/privatekey.pem with the actual paths to your SSL certificate and private key. This ensures that websockify is accepting only encrypted connections through TLS/SSL on port 6080.

    Step 2: Configure Firewall (UFW)

    Using UFW (Uncomplicated Firewall) is an effective way to manage network traffic. Here, you'll set up rules to allow only HTTPS traffic on port 6080:

    1. Check if UFW is Active:

      sudo ufw status
      

      If UFW is not active:

      sudo ufw enable
      
    2. Allow HTTPS Traffic on Port 6080: You only need to specify the port as UFW will, by default, allow traffic based on the service type. Since websockify when run with SSL is using HTTPS-like traffic, configure UFW to allow traffic on port 6080:

      sudo ufw allow 6080/tcp comment 'Allow secure noVNC connections'
      
    3. Reload UFW to Apply the Changes:

      sudo ufw reload
      
    4. Verify the Rules:

      sudo ufw status
      

      Ensure that the rule for allowing access on port 6080 is listed.

    Step 3: Test the Configuration

    After setting up websockify with SSL and configuring the UFW firewall rules, you should test the configuration to ensure that everything is working correctly:

    1. Access from a Browser: Try accessing your noVNC setup via the browser using https://your-ip-address:6080/vnc.html. Replace your-ip-address with the actual server IP.

    2. Use Browser's Developer Tools: Check the security settings in the browser's developer tools to confirm that the connection is using TLS/SSL.

    3. Check Connectivity: If you are unable to access it, double-check the firewall settings, SSL certificate paths in the websockify command, and ensure that there's no typo in the URL.

    Additional Security Tips

    • Regularly Update Certificates: Ensure your certificates are updated regularly, especially if using certificates from providers like Let's Encrypt, which have shorter validity periods.
    • Monitor Access Logs: Keep an eye on access logs to identify any unauthorized access attempts.
    • Restrict Access Further: If possible, restrict access to the noVNC service to known IP addresses to enhance security.

    Following these steps will help you secure websockify running for noVNC, ensuring that only HTTPS traffic is allowed on the specified port.

  15. User

    Error code: 405

    Message: Method Not Allowed.

    Error code explanation: 405 - Specified method is invalid for this resource.

  16. Assistant

    The HTTP 405 "Method Not Allowed" error indicates that the request method sent by the client is recognized by the server but is not supported by the target resource. For instance, if a client sends a POST request to a resource that only supports GET requests, the server will respond with a 405 error. This error is common in web-based applications and APIs when a certain HTTP method is not properly handled.

    Here are several steps you can follow to investigate and potentially resolve a 405 error:

    1. Check Allowed Methods

    First, ensure you know what HTTP methods the server endpoint supports. This information is sometimes included in the 405 error response as an Allow header, which lists the valid methods (e.g., Allow: GET, HEAD). If this isn’t clear from the error response, you might need to refer to the server's API documentation or source code.

    2. Review the Request

    Make sure that the request from the client is using the correct HTTP method supported by the server for that particular route or resource. This is often an issue where, for example, POST is used instead of PUT, or GET is used for a route that requires POST.

    3. Examine Server Configuration

    If the correct method is being used, then the server configuration might be incorrectly blocking it or not routing it correctly. If you are using a web server like Apache or Nginx, check your configuration files (e.g., .htaccess in Apache or server blocks in Nginx) to make sure that the correct methods are allowed. For example, in Nginx, you might see something like:

    location /api {
        limit_except GET {
            deny all;
        }
    }
    

    This configuration would allow only GET requests to the /api path and deny others, potentially resulting in a 405 error if other methods are attempted.

    4. Check Middleware and Handlers

    In web frameworks, middleware or other request handlers could be responsible for returning a 405 error. If you’re working within a framework (like Express.js, Django, Flask, etc.), ensure that your routes are correctly set up to accept the intended methods.

    5. Logging and Debugging

    Enable detailed logging if it's not already active, to get more insights into what happens when the request is made. Review the logs to see if the framework or a specific part of your code is responsible for returning the 405 error.

    6. Test with Tools

    Use tools like Postman or Curl to manually test the HTTP methods against the endpoint. This can help you isolate whether the issue is with the client or server-side setup.

    Example Curl Command:

    If you’re unsure about which method you should be using, you can test with Curl:

    curl -X POST -d "param1=value1&param2=value2" http://example.com/resource
    

    Replace "POST" with different methods like "GET", "PUT", "DELETE" etc., to test different behaviors.

    7. Client-Side Review

    If this issue is emerging from a front-end application, review the AJAX or fetch call that initiates the request. Make sure the method specified there matches what the server expects.

    8. Consult Documentation or Support

    If all else fails and you’re using a third-party API or service, check their documentation or reach out to their support team for clarity on allowed methods for the endpoints you are trying to use.

    By following these steps, you should be able to diagnose and correct the cause of the HTTP 405 "Method Not Allowed" error in your application.

  17. User

    novnc get Error code: 405

    Message: Method Not Allowed.

    Error code explanation: 405 - Specified method is invalid for this resource.

  18. Assistant

    An HTTP 405 "Method Not Allowed" error in a noVNC setup typically implies that there's a mismatch or misconfiguration in how web traffic is being handled, particularly around the WebSocket connections that noVNC relies on to communicate with the VNC server via websockify. Here’s how you can go about troubleshooting and hopefully resolving this issue:

    Step 1: Analyze the Request

    • Check Method Used: Identify which HTTP method is causing the issue. With noVNC, the primary interaction should be a WebSocket upgrade request, which initially starts as an HTTP GET request with an "Upgrade: websocket" header. Often, this error could occur if something in the environment (like a proxy or web server) doesn't correctly interpret or route the WebSocket upgrade request.

    Step 2: Inspect Web Server/Proxy Configuration

    If you're using a proxy server (like Nginx or Apache) in front of websockify, make sure that the configuration explicitly supports WebSocket upgrades and lets through the appropriate headers. Examples are as follows:

    For Nginx:

    location /websockify {
        proxy_pass http://localhost:6080;
        proxy_http_version 1.1;
        proxy_set_header Upgrade $http_upgrade;
        proxy_set_header Connection "upgrade";
        proxy_read_timeout 86400; # can help with timeouts on long connections
    
        # Optional: allow only local network access
        # allow 192.168.0.0/16;
        # deny all;
    }
    

    For Apache:

    RewriteEngine On
    RewriteCond %{HTTP:Upgrade} =websocket [NC]
    RewriteRule /websockify ws://localhost:6080%{REQUEST_URI} [P,L]
    
    ProxyPass "/websockify" "http://localhost:6080/"
    ProxyPassReverse "/websockify" "http://localhost:6080/"
    ProxyPreserveHost On
    

    Step 3: Verify websockify Settings

    • Correct Port and SSL Configuration: Ensure that websockify is running on the correct port and with the correct SSL configuration if you are accessing it via HTTPS. This would involve using the --cert and --key parameters as discussed earlier.
    websockify --web=/usr/share/novnc/ --cert=/path/to/your/cert.pem --key=/path/to/your/key.pem 6080 localhost:5900
    

    Step 4: Testing Direct Access

    • Direct Access Testing: Try connecting directly to the websockify server bypassing any proxy settings to rule out proxy misconfiguration.
    • Browser Developer Tools: Use tools like Chrome or Firefox developer tools to inspect the WebSocket frames for more clarity on when and why the 405 error occurs.

    Step 5: Review noVNC Client Configuration

    • Correct URL and Port: Double-check the configuration that initializes noVNC on the client side. Ensure that the path, port, and protocol (ws:// or wss://) are correctly pointed to your websockify instance.
    var rfb = new RFB(document.getElementById('screen'), "wss://your-domain.com/websockify");
    

    Step 6: Check For Errors in Logs

    • Server and Proxy Logs: Look through the logs of your server and proxy for any indications that could point to why a 405 error is occurring. Things like "method not allowed" or "bad request" can give you more context.

    Step 7: CORS Settings

    • If you are calling across domains (less likely in internal setups like VNC), ensure CORS settings are appropriately configured to allow such requests.

    Step 8: Firewall and Security Settings

    • Firewall Rules: Confirm that no firewall rules are incorrectly blocking or filtering out legitimate web traffic, including WebSocket connections.

    By following these steps, you should be able to identify the cause of the 405 error in your noVNC setup and take appropriate measures to resolve it. If the problem persists, additional diagnostic information, such as specific log entries or the exact setup configuration, might be needed to provide further assistance.

  19. User

    why the browser on my android phone only show directory listing for the novnc

  20. Assistant

    If your browser on an Android phone is showing a directory listing instead of serving the noVNC client interface when you navigate to the noVNC URL, it typically suggests that the web server (in this context, likely websockify serving static files) is not configured to serve the correct index file (e.g., vnc.html or index.html). Here is how you can troubleshoot and resolve this issue:

    1. Check the --web Directory Content

    Ensure that the directory specified in the --web argument of your websockify command contains the noVNC client files, especially vnc.html or index.html. The directory should look something like this when listed:

    ls /usr/share/novnc/
    

    You should see files such as vnc.html, vnc_lite.html, or possibly an index.html depending on the version of noVNC. If these files are missing, you'll need to ensure that noVNC is correctly installed or that the path specified in the --web argument is correct.

    2. Specify the Default File to Serve

    If the correct files are present, but websockify is not serving them automatically, you may need to explicitly specify which file to serve by default when a user navigates to the directory URL. This can depend on how you've set up websockify or your web server:

    • For Websockify: If you are running websockify standalone with the --web parameter handling file serving, it should automatically serve vnc.html or index.html when accessing the root of the specified web directory. If not, ensure your command looks correct, e.g.:

      websockify --web=/usr/share/novnc/ --cert=/path/to/your/certificate.pem --key=/path/to/your/key.pem 6080 localhost:5900
      
    • For a Web Server (like nginx or Apache): If you are using a standard web server to serve the noVNC files, you need to configure it to serve vnc.html or index.html as the default document. Here are sample snippets for common web servers:

      Nginx:

      server {
          listen 80;
          server_name example.com;
      
          location / {
              root /usr/share/novnc/;
              index vnc.html vnc_lite.html index.html;
              try_files $uri $uri/ =404;
          }
      }
      

      Apache:

      <VirtualHost *:80>
          DocumentRoot "/usr/share/novnc"
          ServerName example.com
      
          <Directory "/usr/share/novnc">
              Options -Indexes
              AllowOverride All
              Require all granted
              DirectoryIndex vnc.html vnc_lite.html index.html
          </Directory>
      </VirtualHost>
      

    3. Correct File Permissions

    Check that the webserver has the correct permissions to read the files in the noVNC directory:

    sudo chmod -R 755 /usr/share/novnc/
    

    4. Clear Browser Cache

    Sometimes the browser cache can cause old or unexpected behaviors to persist. Try clearing your browser’s cache, or use an incognito/private window to access the noVNC URL again.

    5. Validate the URL

    Check if you are accessing the right URL and ensure there are no typographical errors. Also, make sure the port is correctly appended to the URL if needed, for example, http://example.com:6080/vnc.html.

    By following these steps, you can likely resolve the issue where a directory listing is shown instead of the noVNC interface. Analyze each part to ensure the web service is correctly configured to serve the required HTML files for noVNC from the desired directory.

  21. User

    got a Your connection is not private warning when visit noVNC

  22. Assistant

    The "Your connection is not private" warning in your browser when visiting the noVNC interface typically informs you about issues related to SSL/TLS certificate validation. Here's how to address this issue step-by-step:

    1. Understanding the Error

    The warning often arises because:

    • The SSL/TLS certificate isn’t trusted by your browser.
    • The certificate has expired.
    • The domain name on the certificate doesn’t match the one in the browser’s address bar.
    • A self-signed certificate is being used.

    2. Check Your SSL/TLS Certificate

    Examine the certificate installed for the noVNC (websockify) service:

    • Validity: Ensure the certificate hasn’t expired.
    • Domain Name: Make sure the certificate’s domain name matches what you type in the address bar.
    • Trust Chain: Ensure the browser trusts the certificate issuer. Browsers will not trust self-signed certificates unless manually added.
    • You can view these details by clicking on the lock/icon next to the URL in your browser, depending on which browser you use.

    3. Using a Trusted Certificate

    If you’re using a self-signed certificate, consider obtaining one from a trusted Certificate Authority (CA) like Let's Encrypt, especially if the noVNC interface is accessed frequently by users or over the Internet.

    Example using Let’s Encrypt:

    • Install certbot:
      sudo apt install certbot
      
    • Request a certificate (ensure your domain is correctly pointing to the IP address of your server):
      sudo certbot certonly --standalone -d yourdomain.com
      
    • Use the generated certificate (typically located in /etc/letsencrypt/live/yourdomain.com/) in your websockify configuration.

    4. Modify Websockify to Use the Trusted Certificate

    Adjust the websockify startup command to use your new or existing trusted certificate:

    websockify --cert=/etc/letsencrypt/live/yourdomain.com/fullchain.pem --key=/etc/letsencrypt/live/yourdomain.com/privkey.pem -D [port] [target]
    

    Replace [port] and [target] with your configuration details.

    5. Restart and Verify

    • Restart the websockify service to apply the changes.
    • Open the noVNC URL and check the certificate details to ensure it’s applying the correct, updated certificate.

    6. Clear Browser Cache

    Sometimes browsers store certificates in the cache and show outdated errors. Clear your browser’s cache and try accessing the URL again.

    7. For Development or Internal Usage

    If you are in a development environment or using noVNC internally (and understand the risks of a self-signed certificate), you can instruct users to proceed past the warning:

    • This can typically be done by clicking "Advanced" on the warning page and then clicking "Proceed to [URL]".

    8. Add an Exception

    • You can also add a security exception for your certificate in your browser. However, this is generally not recommended unless you are fully aware of the security implications.

    By following these steps, you can either validate the current SSL/TLS setup or update it to ensure that visitors to the noVNC interface don't encounter a "Your connection is not private" warning. Moving to a trusted certificate from a CA like Let's Encrypt is usually the best route for public services.