Please correct the code in the location from "START: Please modify the code correctly."…
- User
Please correct the code in the location from "START: Please modify the code correctly." to "END: Please modify the code correctly."
<<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low
// configuration registers input wire [31:0] src_addr_i, input wire [31:0] dst_addr_i, input wire [15:0] byte_len_i, input wire start_i, output wire done_o, // AMBA AXI interface (AW channel) output wire [3:0] awid_o, output wire [31:0] awaddr_o, output wire [3:0] awlen_o, output wire [2:0] awsize_o, output wire [1:0] awburst_o, output wire awvalid_o, input wire awready_i, // AMBA AXI interface (W channel) output wire [3:0] wid_o, output wire [31:0] wdata_o, output wire [3:0] wstrb_o, output wire wlast_o, output wire wvalid_o, input wire wready_i, // AMBA AXI interface (B channel) input wire [3:0] bid_i, input wire [1:0] bresp_i, input wire bvalid_i, output wire bready_o, // AMBA AXI interface (AR channel) output wire [3:0] arid_o, output wire [31:0] araddr_o, output wire [3:0] arlen_o, output wire [2:0] arsize_o, output wire [1:0] arburst_o, output wire arvalid_o, input wire arready_i, // AMBA AXI interface (R channel) input wire [3:0] rid_i, input wire [31:0] rdata_i, input wire [1:0] rresp_i, input wire rlast_i, input wire rvalid_i, output wire rready_o);
// mnemonics for state values localparam S_IDLE = 3'd0, S_RREQ = 3'd1, S_RDATA = 3'd2, S_WREQ = 3'd3, S_WDATA = 3'd4; reg [2:0] state, state_n; reg [31:0] src_addr, src_addr_n; reg [31:0] dst_addr, dst_addr_n; reg [15:0] cnt, cnt_n; reg [3:0] wcnt, wcnt_n; reg arvalid, rready, awvalid, wvalid, wlast, done; wire fifo_full, fifo_empty; reg fifo_wren, fifo_rden; wire [31:0] fifo_rdata; // it's desirable to code registers in a simple way always_ff @(posedge clk) if (!rst_n) begin state <= S_IDLE; src_addr <= 32'd0; dst_addr <= 32'd0; cnt <= 16'd0; wcnt <= 4'd0; end else begin state <= state_n; src_addr <= src_addr_n; dst_addr <= dst_addr_n; cnt <= cnt_n; wcnt <= wcnt_n; end // this block programs output values and next register values // based on states. always_comb begin // ********************** // START:Please modify the code correctly. state_n = state; src_addr_n = src_addr; dst_addr_n = dst_addr; cnt_n = cnt; arvalid = 1'b0; rready = 1'b0; awvalid = 1'b0; wvalid = 1'b0; done = 1'b0; case (state) S_IDLE: begin done = 1'b1; if (start_i & byte_len_i!=16'd0) begin src_addr_n = src_addr_i; dst_addr_n = dst_addr_i; cnt_n = byte_len_i; state_n = S_RREQ; end end S_RREQ: begin arvalid = 1'b1; if (arready_i) begin state_n = S_RDATA; src_addr_n = src_addr + 'd4; end end S_RDATA: begin rready = 1'b1; if (rvalid_i && rlast_i) begin fifo_wren = 1'b1; state_n = S_WREQ; end if (rvalid_i && !rlast_i) begin fifo_wren = 1'b1; state_n = S_RDATA; end end S_WREQ: begin awvalid = 1'b1; if (awready_i) begin state_n = S_WDATA; dst_addr_n = dst_addr + 'd4; //cnt_n = cnt - 16'd4; end end S_WDATA: begin wvalid = 1'b1; if (wready_i) begin fifo_rden = 1'b1; if (cnt==16'd0 && wlast) begin state_n = S_IDLE; end if (cnt!=16'd0 && wlast) begin state_n = S_RREQ; end if (!wlast) begin state_n = S_WDATA; end end end endcase // END:Please modify the code correctly. // ********************** end DMAC_FIFO u_fifo ( .clk (clk), .rst_n (rst_n), .full_o (fifo_full), .wren_i (fifo_wren), .wdata_i (rdata_i), .empty_o (fifo_empty), .rden_i (fifo_rden), .rdata_o (fifo_rdata) ); // Output assigments assign done_o = done; assign awid_o = 4'd0; assign awaddr_o = dst_addr; assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1; assign awsize_o = 3'b010; // 4 bytes per transfer assign awburst_o = 2'b01; // incremental assign awvalid_o = awvalid; assign wid_o = 4'd0; assign wdata_o = fifo_rdata; assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid assign wlast_o = wlast; assign wvalid_o = wvalid; assign bready_o = 1'b1; assign arvalid_o = arvalid; assign araddr_o = src_addr; assign arid_o = 4'd0; assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1; assign arsize_o = 3'b010; // 4 bytes per transfer assign arburst_o = 2'b01; // incremental assign arvalid_o = arvalid; assign rready_o = rready & !fifo_full;endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>
<<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>
define IP_VER 32'h000define SRC_ADDR 32'h100define DST_ADDR 32'h104define LEN_ADDR 32'h108define STAT_ADDR 32'h110define START_ADDR 32'h10c`define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();
reg clk; reg rst_n; // clock generation initial begin clk = 1'b0; forever #10 clk = !clk; end // reset generation initial begin rst_n = 1'b0; // active at time 0 repeat (3) @(posedge clk); // after 3 cycles, rst_n = 1'b1; // release the reset end // enable waveform dump initial begin \$dumpvars(0, u_DUT); \$dumpfile("dump.vcd"); end// timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end
APB apb_if (.clk(clk)); AXI_AW_CH aw_ch (.clk(clk)); AXI_W_CH w_ch (.clk(clk)); AXI_B_CH b_ch (.clk(clk)); AXI_AR_CH ar_ch (.clk(clk)); AXI_R_CH r_ch (.clk(clk)); task test_init(); int data; apb_if.init(); @(posedge rst_n); // wait for a release of the reset repeat (10) @(posedge clk); // wait another 10 cycles apb_if.read(`IP_VER, data); \$display("---------------------------------------------------"); \$display("IP version: %x", data); \$display("---------------------------------------------------"); \$display("---------------------------------------------------"); \$display("Reset value test"); \$display("---------------------------------------------------"); apb_if.read(`SRC_ADDR, data); if (data===0) \$display("DMA_SRC(pass): %x", data); else begin \$display("DMA_SRC(fail): %x", data); @(posedge clk); \$finish; end apb_if.read(`DST_ADDR, data); if (data===0) \$display("DMA_DST(pass): %x", data); else begin \$display("DMA_DST(fail): %x", data); @(posedge clk); \$finish; end apb_if.read(`LEN_ADDR, data); if (data===0) \$display("DMA_LEN(pass): %x", data); else begin \$display("DMA_LEN(fail): %x", data); @(posedge clk); \$finish; end apb_if.read(`STAT_ADDR, data); if (data===1) \$display("DMA_STATUS(pass): %x", data); else begin \$display("DMA_STATUS(fail): %x", data); @(posedge clk); \$finish; end endtask task test_dma(input int src, input int dst, input int len); int data; int word; realtime elapsed_time; \$display("---------------------------------------------------"); \$display("Load data to memory"); \$display("---------------------------------------------------"); for (int i=src; i<(src+len); i=i+4) begin word = \$random; u_mem.write_word(i, word); end \$display("---------------------------------------------------"); \$display("Configuration test"); \$display("---------------------------------------------------"); apb_if.write(`SRC_ADDR, src); apb_if.read(`SRC_ADDR, data); if (data===src) \$display("DMA_SRC(pass): %x", data); else begin \$display("DMA_SRC(fail): %x", data); @(posedge clk); \$finish; end apb_if.write(`DST_ADDR, dst); apb_if.read(`DST_ADDR, data); if (data===dst) \$display("DMA_DST(pass): %x", data); else begin \$display("DMA_DST(fail): %x", data); @(posedge clk); \$finish; end apb_if.write(`LEN_ADDR, len); apb_if.read(`LEN_ADDR, data); if (data===len) \$display("DMA_LEN(pass): %x", data); else begin \$display("DMA_LEN(fail): %x", data); @(posedge clk); \$finish; end \$display("---------------------------------------------------"); \$display("DMA start"); \$display("---------------------------------------------------"); apb_if.write(`START_ADDR, 32'h1); elapsed_time = \$realtime; \$display("---------------------------------------------------"); \$display("Wait for a DMA completion"); \$display("---------------------------------------------------"); data = 0; while (data!=1) begin apb_if.read(`STAT_ADDR, data); repeat (100) @(posedge clk); end @(posedge clk); elapsed_time = \$realtime - elapsed_time; \$timeformat(-9, 0, " ns", 10); \$display("Elapsed time for DMA: %t", elapsed_time); \$display("---------------------------------------------------"); \$display("DMA completed"); \$display("---------------------------------------------------"); repeat (len) @(posedge clk); // to make sure data is written \$display("---------------------------------------------------"); \$display("verify data"); \$display("---------------------------------------------------"); for (int i=0; i<len; i=i+4) begin logic [31:0] src_word; logic [31:0] dst_word; src_word = u_mem.read_word(src+i); dst_word = u_mem.read_word(dst+i); if (src_word!==dst_word) begin \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i); end end endtask int src, dst, len; // main initial begin test_init(); src = 'h0000_1000; dst = 'h0000_2000; len = 'h0100; \$display("==================================================="); \$display("= 1st trial"); \$display("= Copying %x bytes from %x to %x", len, src, dst); \$display("==================================================="); test_dma(src, dst, len); src = 'h1234_1234; dst = 'hABCD_ABCC; len = 'h0F00; \$display("==================================================="); \$display("= 2nd trial (long transfer)"); \$display("= Copying %x bytes from %x to %x", len, src, dst); \$display("==================================================="); test_dma(src, dst, len); src = 'h4278_0000; dst = 'h4278_1000; len = 'h0F10; \$display("==================================================="); \$display("= 3rd trial (long transfer-2)"); \$display("= Copying %x bytes from %x to %x", len, src, dst); \$display("==================================================="); test_dma(src, dst, len); \$finish; end AXI_SLAVE u_mem ( .clk (clk), .rst_n (rst_n), .aw_ch (aw_ch), .w_ch (w_ch), .b_ch (b_ch), .ar_ch (ar_ch), .r_ch (r_ch) ); DMAC_TOP u_DUT ( .clk (clk), .rst_n (rst_n), // APB interface .psel_i (apb_if.psel), .penable_i (apb_if.penable), .paddr_i (apb_if.paddr[11:0]), .pwrite_i (apb_if.pwrite), .pwdata_i (apb_if.pwdata), .pready_o (apb_if.pready), .prdata_o (apb_if.prdata), .pslverr_o (apb_if.pslverr), // AXI AW channel .awid_o (aw_ch.awid), .awaddr_o (aw_ch.awaddr), .awlen_o (aw_ch.awlen), .awsize_o (aw_ch.awsize), .awburst_o (aw_ch.awburst), .awvalid_o (aw_ch.awvalid), .awready_i (aw_ch.awready), // AXI W channel .wid_o (w_ch.wid), .wdata_o (w_ch.wdata), .wstrb_o (w_ch.wstrb), .wlast_o (w_ch.wlast), .wvalid_o (w_ch.wvalid), .wready_i (w_ch.wready), // AXI B channel .bid_i (b_ch.bid), .bresp_i (b_ch.bresp), .bvalid_i (b_ch.bvalid), .bready_o (b_ch.bready), // AXI AR channel .arid_o (ar_ch.arid), .araddr_o (ar_ch.araddr), .arlen_o (ar_ch.arlen), .arsize_o (ar_ch.arsize), .arburst_o (ar_ch.arburst), .arvalid_o (ar_ch.arvalid), .arready_i (ar_ch.arready), // AXI R channel .rid_i (r_ch.rid), .rdata_i (r_ch.rdata), .rresp_i (r_ch.rresp), .rlast_i (r_ch.rlast), .rvalid_i (r_ch.rvalid), .rready_o (r_ch.rready) );endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>
<StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low
// AMBA APB interface input wire psel_i, input wire penable_i, input wire [11:0] paddr_i, input wire pwrite_i, input wire [31:0] pwdata_i, output reg pready_o, output reg [31:0] prdata_o, output reg pslverr_o, // configuration registers output reg [31:0] src_addr_o, output reg [31:0] dst_addr_o, output reg [15:0] byte_len_o, output wire start_o, input wire done_i);
// Configuration register to read/write reg [31:0] src_addr; reg [31:0] dst_addr; reg [15:0] byte_len; //---------------------------------------------------------- // Write //---------------------------------------------------------- // an APB write occurs when PSEL & PENABLE & PWRITE // clk : __--__--__--__--__--__--__--__--__--__-- // psel : ___--------_____________________________ // penable : _______----_____________________________ // pwrite : ___--------_____________________________ // wren : _______----_____________________________ // // DMA start command must be asserted when APB writes 1 to the DMA_CMD // register // clk : __--__--__--__--__--__--__--__--__--__-- // psel : ___--------_____________________________ // penable : _______----_____________________________ // pwrite : ___--------_____________________________ // paddr : |DMA_CMD| // pwdata : | 1 | // start : _______----_____________________________ wire wren = psel_i & penable_i & pwrite_i; always @(posedge clk) begin if (!rst_n) begin src_addr <= 32'd0; dst_addr <= 32'd0; byte_len <= 16'd0; end else if (wren) begin case (paddr_i) 'h100: src_addr <= pwdata_i[31:0]; 'h104: dst_addr <= pwdata_i[31:0]; 'h108: byte_len <= pwdata_i[15:0]; endcase end end wire start = wren & (paddr_i=='h10C) & pwdata_i[0]; //---------------------------------------------------------- // READ //---------------------------------------------------------- // an APB read occurs when PSEL & PENABLE & !PWRITE // To make read data a direct output from register, // this code shall buffer the muxed read data into a register // in the SETUP cycle (PSEL & !PENABLE) // clk : __--__--__--__--__--__--__--__--__--__-- // psel : ___--------_____________________________ // penable : _______----_____________________________ // pwrite : ________________________________________ // reg update : ___----_________________________________ // prdata : |DATA reg [31:0] rdata; always @(posedge clk) begin if (!rst_n) begin rdata <= 32'd0; end else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram case (paddr_i) 'h0: rdata <= 32'h0001_2024; 'h100: rdata <= src_addr; 'h104: rdata <= dst_addr; 'h108: rdata <= {16'd0, byte_len}; 'h110: rdata <= {31'd0, done_i}; default: rdata <= 32'd0; endcase end end // output assignments assign pready_o = 1'b1; assign prdata_o = rdata; assign pslverr_o = 1'b0; assign src_addr_o = src_addr; assign dst_addr_o = dst_addr; assign byte_len_o = byte_len; assign start_o = start;endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>
<<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,
output wire full_o, input wire wren_i, input wire [DATA_WIDTH-1:0] wdata_i, output wire empty_o, input wire rden_i, output wire [DATA_WIDTH-1:0] rdata_o);
localparam FIFO_DEPTH = (1<<DEPTH_LG2); reg [DATA_WIDTH-1:0] data[FIFO_DEPTH]; reg full, full_n, empty, empty_n; reg [DEPTH_LG2:0] wrptr, wrptr_n, rdptr, rdptr_n; // reset entries to all 0s always_ff @(posedge clk) if (!rst_n) begin full <= 1'b0; empty <= 1'b1; // empty after as reset wrptr <= {(DEPTH_LG2+1){1'b0}}; rdptr <= {(DEPTH_LG2+1){1'b0}}; for (int i=0; i<FIFO_DEPTH; i++) begin data[i] <= {DATA_WIDTH{1'b0}}; end end else begin full <= full_n; empty <= empty_n; wrptr <= wrptr_n; rdptr <= rdptr_n; if (wren_i) begin data[wrptr[DEPTH_LG2-1:0]] <= wdata_i; end end always_comb begin wrptr_n = wrptr; rdptr_n = rdptr; if (wren_i) begin wrptr_n = wrptr + 'd1; end if (rden_i) begin rdptr_n = rdptr + 'd1; end empty_n = (wrptr_n == rdptr_n); full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2]) &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]); end // synthesis translate_off always @(posedge clk) begin if (full_o & wren_i) begin \$display("FIFO overflow"); @(posedge clk); \$finish; end end always @(posedge clk) begin if (empty_o & rden_i) begin \$display("FIFO underflow"); @(posedge clk); \$finish; end end // synthesis translate_on assign full_o = full; assign empty_o = empty; assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>
<<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low
// AMBA APB interface input wire psel_i, input wire penable_i, input wire [11:0] paddr_i, input wire pwrite_i, input wire [31:0] pwdata_i, output reg pready_o, output reg [31:0] prdata_o, output reg pslverr_o, // AMBA AXI interface (AW channel) output wire [3:0] awid_o, output wire [31:0] awaddr_o, output wire [3:0] awlen_o, output wire [2:0] awsize_o, output wire [1:0] awburst_o, output wire awvalid_o, input wire awready_i, // AMBA AXI interface (AW channel) output wire [3:0] wid_o, output wire [31:0] wdata_o, output wire [3:0] wstrb_o, output wire wlast_o, output wire wvalid_o, input wire wready_i, // AMBA AXI interface (B channel) input wire [3:0] bid_i, input wire [1:0] bresp_i, input wire bvalid_i, output wire bready_o, // AMBA AXI interface (AR channel) output wire [3:0] arid_o, output wire [31:0] araddr_o, output wire [3:0] arlen_o, output wire [2:0] arsize_o, output wire [1:0] arburst_o, output wire arvalid_o, input wire arready_i, // AMBA AXI interface (R channel) input wire [3:0] rid_i, input wire [31:0] rdata_i, input wire [1:0] rresp_i, input wire rlast_i, input wire rvalid_i, output wire rready_o);
wire [31:0] src_addr; wire [31:0] dst_addr; wire [15:0] byte_len; wire start; wire done; DMAC_CFG u_cfg( .clk (clk), .rst_n (rst_n), // AMBA APB interface .psel_i (psel_i), .penable_i (penable_i), .paddr_i (paddr_i), .pwrite_i (pwrite_i), .pwdata_i (pwdata_i), .pready_o (pready_o), .prdata_o (prdata_o), .pslverr_o (pslverr_o), .src_addr_o (src_addr), .dst_addr_o (dst_addr), .byte_len_o (byte_len), .start_o (start), .done_i (done) ); DMAC_ENGINE u_engine( .clk (clk), .rst_n (rst_n), // configuration registers .src_addr_i (src_addr), .dst_addr_i (dst_addr), .byte_len_i (byte_len), .start_i (start), .done_o (done), // AMBA AXI interface (AW channel) .awid_o (awid_o), .awaddr_o (awaddr_o), .awlen_o (awlen_o), .awsize_o (awsize_o), .awburst_o (awburst_o), .awvalid_o (awvalid_o), .awready_i (awready_i), // AMBA AXI interface (W channel) .wid_o (wid_o), .wdata_o (wdata_o), .wstrb_o (wstrb_o), .wlast_o (wlast_o), .wvalid_o (wvalid_o), .wready_i (wready_i), // AMBA AXI interface (B channel) .bid_i (bid_i), .bresp_i (bresp_i), .bvalid_i (bvalid_i), .bready_o (bready_o), // AMBA AXI interface (AR channel) .arid_o (arid_o), .araddr_o (araddr_o), .arlen_o (arlen_o), .arsize_o (arsize_o), .arburst_o (arburst_o), .arvalid_o (arvalid_o), .arready_i (arready_i), // AMBA AXI interface (R channel) .rid_i (rid_i), .rdata_i (rdata_i), .rresp_i (rresp_i), .rlast_i (rlast_i), .rvalid_i (rvalid_i), .rready_o (rready_o) );endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>
<<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"
interface AXI_AW_CH #( parameter ADDR_WIDTH =
AXI_ADDR_WIDTH, parameter ID_WIDTH =AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;endinterface
interface AXI_W_CH #( parameter DATA_WIDTH =
AXI_DATA_WIDTH, parameter ID_WIDTH =AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;endinterface
interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;
endinterface
interface AXI_AR_CH #( parameter ADDR_WIDTH =
AXI_ADDR_WIDTH, parameter ID_WIDTH =AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;endinterface
interface AXI_R_CH #( parameter DATA_WIDTH =
AXI_DATA_WIDTH, parameter ID_WIDTH =AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;endinterface
interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;
modport master ( input clk, input pready, prdata, pslverr, output psel, penable, paddr, pwrite, pwdata ); task init(); psel = 1'b0; penable = 1'b0; paddr = 32'd0; pwrite = 1'b0; pwdata = 32'd0; endtask task write(input int addr, input int data); #1 psel = 1'b1; penable = 1'b0; paddr = addr; pwrite = 1'b1; pwdata = data; @(posedge clk); #1 penable = 1'b1; @(posedge clk); while (pready==1'b0) begin @(posedge clk); end psel = 1'b0; penable = 1'b0; paddr = 'hX; pwrite = 1'bx; pwdata = 'hX; endtask task read(input int addr, output int data); #1 psel = 1'b1; penable = 1'b0; paddr = addr; pwrite = 1'b0; pwdata = 'hX; @(posedge clk); #1 penable = 1'b1; @(posedge clk); while (pready==1'b0) begin @(posedge clk); end data = prdata; psel = 1'b0; penable = 1'b0; paddr = 'hX; pwrite = 1'bx; pwdata = 'hX; endtaskendinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>
<<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"
module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH =
AXI_DATA_WIDTH, parameter ID_WIDTH =AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active lowAXI_AW_CH aw_ch, AXI_W_CH w_ch, AXI_B_CH b_ch, AXI_AR_CH ar_ch, AXI_R_CH r_ch);
localparam DATA_DEPTH = 1<<ADDR_WIDTH; logic [7:0] mem[DATA_DEPTH]; function void write_byte(int addr, input bit [7:0] wdata); mem[addr] = wdata; endfunction function void write_word(int addr, input bit [31:0] wdata); for (int i=0; i<4; i++) begin write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8] end endfunction function bit [7:0] read_byte(int addr); read_byte = mem[addr]; endfunction function bit [31:0] read_word(int addr); for (int i=0; i<4; i++) begin read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8] end endfunction //---------------------------------------------------------- // write channels (AW, W, B) //---------------------------------------------------------- localparam logic [1:0] S_W_IDLE = 0, S_W_AWREADY = 1, S_W_BURST = 2, S_W_RESP = 3; logic [1:0] wstate, wstate_n; logic [7:0] wcnt, wcnt_n; logic [ADDR_WIDTH-1:0] waddr, waddr_n; logic [ID_WIDTH-1:0] wid, wid_n; logic [3:0] wlen, wlen_n; always_ff @(posedge clk) if (!rst_n) begin wstate <= S_W_IDLE; wcnt <= 8'd0; waddr <= {ADDR_WIDTH{1'b0}}; wid <= {ID_WIDTH{1'b0}}; wlen <= 4'd0; end else begin wstate <= wstate_n; wcnt <= wcnt_n; waddr <= waddr_n; wid <= wid_n; wlen <= wlen_n; end always @(*) begin wstate_n = wstate; wcnt_n = wcnt; waddr_n = waddr; wid_n = wid; wlen_n = wlen; aw_ch.awready = 1'b0; w_ch.wready = 1'b0; b_ch.bvalid = 1'b0; case (wstate) S_W_IDLE: begin if (aw_ch.awvalid) begin if (AWREADY_DELAY == 0) begin waddr_n = aw_ch.awaddr; wid_n = aw_ch.awid; wlen_n = aw_ch.awlen; aw_ch.awready = 1'b1; wstate_n = S_W_BURST; end else begin wcnt_n = AWREADY_DELAY-1; wstate_n = S_W_AWREADY; end end end S_W_AWREADY: begin if (wcnt==0) begin waddr_n = aw_ch.awaddr; wid_n = aw_ch.awid; wlen_n = aw_ch.awlen; aw_ch.awready = 1'b1; wstate_n = S_W_BURST; end else begin wcnt_n = wcnt - 8'd1; end end S_W_BURST: begin w_ch.wready = 1'b1; if (w_ch.wvalid) begin for (int i=0; i<DATA_WIDTH/8; i++) begin write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8] end waddr_n = waddr + (DATA_WIDTH/8); if (wlen==4'd0) begin wstate_n = S_W_RESP; end else begin wlen_n = wlen - 4'd1; end end end S_W_RESP: begin b_ch.bvalid = 1'b1; if (b_ch.bready) begin wstate_n = S_W_IDLE; end end endcase end //---------------------------------------------------------- // read channel (AR, R) //---------------------------------------------------------- localparam logic [1:0] S_R_IDLE = 0, S_R_ARREADY = 1, S_R_DELAY = 2, S_R_BURST = 3; logic [1:0] rstate, rstate_n; logic [7:0] rcnt, rcnt_n; logic [ADDR_WIDTH-1:0] raddr, raddr_n; logic [ID_WIDTH-1:0] rid, rid_n; logic [3:0] rlen, rlen_n; always_ff @(posedge clk) if (!rst_n) begin rstate <= S_R_IDLE; rcnt <= 8'd0; raddr <= {ADDR_WIDTH{1'b0}}; rid <= {ID_WIDTH{1'b0}}; rlen <= 4'd0; end else begin rstate <= rstate_n; rcnt <= rcnt_n; raddr <= raddr_n; rid <= rid_n; rlen <= rlen_n; end always_comb begin rstate_n = rstate; rcnt_n = rcnt; raddr_n = raddr; rid_n = rid; rlen_n = rlen; ar_ch.arready = 1'b0; r_ch.rvalid = 1'b0; r_ch.rlast = 1'b0; case (rstate) S_R_IDLE: begin if (ar_ch.arvalid) begin if (ARREADY_DELAY == 0) begin raddr_n = ar_ch.araddr; rid_n = ar_ch.arid; rlen_n = ar_ch.arlen; ar_ch.arready = 1'b1; rcnt_n = AR2R_DELAY - 1; rstate_n = S_R_DELAY; end else begin rcnt_n = ARREADY_DELAY-1; rstate_n = S_R_ARREADY; end end end S_R_ARREADY: begin if (rcnt==0) begin raddr_n = ar_ch.araddr; rid_n = ar_ch.arid; rlen_n = ar_ch.arlen; ar_ch.arready = 1'b1; rcnt_n = AR2R_DELAY - 1; rstate_n = S_R_DELAY; end else begin rcnt_n = rcnt - 8'd1; end end S_R_DELAY: begin if (rcnt==0) begin rstate_n = S_R_BURST; end else begin rcnt_n = rcnt - 8'd1; end end S_R_BURST: begin r_ch.rvalid = 1'b1; r_ch.rlast = (rlen==4'd0); for (int i=0; i<DATA_WIDTH/8; i++) begin r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8] end if (r_ch.rready) begin raddr_n = raddr + (DATA_WIDTH/8); if (rlen==4'd0) begin rstate_n = S_R_IDLE; end else begin rlen_n = rlen - 4'd1; end end end endcase end // output assignments assign b_ch.bid = wid; assign b_ch.bresp = 2'd0; assign r_ch.rid = rid; assign r_ch.rresp = 2'd0;endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>
<<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>
ifndef __AXI_TYPEDEF_SVH__define AXI_TYPEDEF_SVHdefine AXI_ADDR_WIDTH 32define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4`endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>
Please verify if the following table is correct using the code provided below.
+-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+
Direct Memory Access (DMA) Controller Design Document V1.0
1 Overview This document specifies the design and implementation of a Direct Memory Access Controller (DMAC) as a part of System-on-a-Chip (SoC). The main purpose of this DMAC design is to integrate into SoC for exchange a large volume of data between memory and peripherals at high speed. The proposed DMAC works on ARM’s Advanced Microcontroller Bus Architecture (AMBA) specification. The DMAC provides an AMBA APB interface to configure the IP, and an AMBA AXI interface to transfer data.
2 Architecture Specification 2.1 General Description Some applications require transferring a volume of data between memory and peripherals without any modification on data. In software, it is commonly served by executing the memcpy library function in C, C++ or other languages. In C, the function has the following interface and copies len bytes from the object pointed by src to the object pointed by dst: void* memcpy(void* dst, const void* src, size_t len). While a pure software-based implementation of memcpy transfers data using CPU instructions, DMA does not use expensive CPU cycles but uses a hardware engine (DMAC) for the transfer. This can significantly speed up data transfers and allows using CPU for other jobs. 2.2 Usage Constraints Below describe constraints in utilizing DMAC v1. -The src and dst addresses are physical addresses. -The src and dst addresses must be a multiple of 4. -The len must be a multiple of 4. -The maximum len is 0xFFFF -Source and destination ranges must not overlap. 2.3 Programming Model Software can use the following sequence to transfer data using DMAC. -1.Write the source address to DMA_SRC register -2.Write the destination address to DMA_DST register -3.Write length to DMA_LEN register -4.Write 1 to bit[0] of DMA_CMD register -5.Wait until DMA_STATUS register has bit[0] as 1.
2.4 Register Map In order to control DMAC, software can configure the following registers. +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | Offset | Reg Name | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x00 | DMA_VER | version | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x04~0xFC | Reserved | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x100 | DMA_SRC | start_addr | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x104 | DMA_DST | start_addr | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+-------------------------------------------------------------------------+ | 0x108 | DMA_LEN | | | | | | | | | | | | | | | | | byte_len | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x10C | DMA_CMD | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | start | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x110 | DMA_STATUS | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | done | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+
2.4.1 DMA VERSION
Field name Bit range R/W Reset value Desciption version [31:0] R 0x0001_2024 The version of this DMA controller. The upper 16 bits represent the major version. The lower 16 bits represent the released year of the version. This document describes behaviors of major version 1. 2.4.2 DMA_SRC
Field name Bit range R/W Reset value Desciption start_addr [31:0] R/W 0x0000_0000 start address of the source range. 2.4.3 DMA_DST
Field name Bit range R/W Reset value Desciption start_addr [31:0] R/W 0x0000_0000 start address of the destination range. 2.4.4 DMA_LEN
Field name Bit range R/W Reset value Desciption byte_len [15:0] R/W 0x0000 Number of bytes to be transferred from the source to the destination. 2.4.5 DMA_CMD Field
Field name Bit range R/W Reset value Desciption start [0] W N/A Writing 1 to this field will initiate a DMA transfer based on DMA_SRC, DMA_DST, and DMA_LEN registers. Software must not write 1 when there’s an on-going transfer. Writing 0 to this field does not affect operation 2.4.6 DMA_STATUS
Field name Bit range R/W Reset value Desciption done [0] R 1 This field is 1 when there’s no on-going DMA transfer. Software must wait this field to be 1 for a completion of a transfer. Software must not initiate a DMA transfer when this field is 0. 3 Micro-architecture v1.1 Specification This section describes microarchitecture of a simple DMAC. It reads data from memory, buffers the data, and write the data into memory. It repeats this procedure until it completes transferring the specified number of bytes. For simplicity, it read/writes one-cycle data (4 bytes) at a time (in other words, burst-1 transfers). For simplicity, this microarchitecture does not consider write responses from the AXI interface. Later versions will support burst transfers and write responses.
3.1 External Interface DMAC v1.1 has the following external interfaces to communicate with other hardware IPs. -AMBA APB interface for configuration -AMBA AXI interface for data transfer
The image you’ve uploaded is a diagram showing the on-chip interconnect of a computer system. Here’s a detailed description: The diagram illustrates how the CPU core, memory, and DMAC (Direct Memory Access Controller) are connected through an on-chip interconnect. The connections also include specific interfaces like Config interface (APB) and Data interface (AXI). “CPU core” is a box on the left side connected to the central “On-chip interconnect” cloud shape with a bidirectional arrow. Below the “CPU core,” there’s another box labeled “Memory,” also connected to the “On-chip interconnect” with a bidirectional arrow. On the right side, there’s a box labeled “DMAC” connected to both “Config interface (APB)” and “Data interface (AXI)” which are in turn connected to the central “On-chip interconnect” with bidirectional arrows. The arrows indicate that data can flow in both directions between these components.
3.2 Block Diagram DMAC v1.1 has the following blocks inside.
The diagram is divided into three main blocks labeled “DMAC_TOP,” “DMAC_CFG,” and “DMAC_ENGINE.” “clk” and “rst” are inputs to the “DMAC_TOP” block. An arrow labeled “APB” connects the “DMAC_TOP” block to the “DMAC_CFG” block. Another arrow labeled “AXI” connects both the “DMAC_TOP” and “DMAC_CFG” blocks to the “DMAC_ENGINE” block. Inside the “DMAC_ENGINE” block, there are four internal components labeled as follows: SRC_ADDR DST_ADDR CNT DATA BUF There’s also a small circular graph with nodes labeled 0 to 3 inside this block. This diagram is likely used to illustrate the flow of data or control signals between these components in a Direct Memory Access Controller configuration. Please let me know if you need more information!
3.3 Configuration Register (lab2) This block receives read/write requests from the APB and configures the registers describes in Section 2.4.
3.4 Finite State Machine (lab3) DMA engine utilizes the following state machine to control operations.
The diagram contains five blue circles representing different states: IDLE, RREQ, RDATA, WREQ, and WDATA. Arrows connect these circles indicating the flow from one state to another. Each arrow has text annotations that describe the conditions for transitioning from one state to another. For example, transitioning from IDLE to RREQ requires writing 1 to DMA_CMD & LEN!=0, and copying DMA_SRC/DST/LEN. There are also annotations on the state circles themselves, such as “done=1” on IDLE and “AWVALID=1” on WDATA.
+-------+--------------------------------------------+------------+-----------------------------------------------------------+----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------+--------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | RVALID=1 | On moving out, | | | | | | | | | | - Buffer RDATA into the data buffer | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) & (counter!=0) | | | | | | | | +------------+-----------------------------------------------------------+----------------------------------------+ | | | | | | | IDLE | (WREADY=1) & (counter==0) | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+
{ "signal": [ { "name": "clk", "wave": "p....|.........." }, { "name": "state", "wave": "2.3.4|..5.6.2...", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "IDLE"] }, { "name": "write to CMD", "wave": "010..|..........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|..........", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|..........", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.........." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0......." }, { "name": "RVALID(in)", "wave": "0....|.10......." }, { "name": "RDATA(in)", "wave": "x....|.4x.......", "data": ["DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....." }, { "name": "AWADDR(out)", "wave": "x....|..5.x.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..." }, { "name": "WDATA(out)", "wave": "x....|....4.x...", "data": ["DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 1. DMA operation with microarchitecture v1.1
4 Micro-architecture v1.2 Specification (lab4) A problem with microarchitecture v1.1 is that it reads/writes data one-by-one. As memory read takes some time, DMAC v1.1 will suffer from poor performance with a long memory read latency (그림 2). We will improve the microarchitecture to transfer a burst of data to minimize performance degradation.
{ "signal": [ { "name": "clk", "wave": "p....|.................." }, { "name": "state", "wave": "2.3.4|..5.6.3.4|..5.6.3.", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|.........|........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|......1.0|......1.", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|......3.x|......3.", "data": ["SRC", "SRC+4", "SRC+8"] }, { "name": "ARLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.......10|.......1" }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0.....1|..0....." }, { "name": "RVALID(in)", "wave": "0....|.10......|.10....." }, { "name": "RDATA(in)", "wave": "x....|.4x......|.4x.....", "data": ["DATA", "DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....|..1.0..." }, { "name": "AWADDR(out)", "wave": "x....|..5.x....|..5.x...", "data": ["DST", "DST+4"] }, { "name": "AWLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....|...10..." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..|....1.0." }, { "name": "WDATA(out)", "wave": "x....|....4.x..|....4.x.", "data": ["DATA", "DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..|.....10." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 2. DMA operation with microarchitecture 1.1. At a time, it transfers single burst of data In Microarchitecture version 2, DMAC transfers up to 16 cycles of data with a single access. This can significantly reduce execution time by transferring data in bursts (그림 3).
{ "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.
- Assistant
The code provided in the
DMAC_ENGINE.svmodule describes the behavior of a Direct Memory Access Controller (DMAC) that interfaces with the AMBA AXI protocol for memory operations and transitions through various states as documented in the table. Based on the code analysis, here are the corrections and additional details pertinent to the operation of the DMAC:-
IDLE State:
- The
donesignal is set to'1'immediately after entering this state, indicating the DMAC is not busy and can accept new commands. - A transition from IDLE to RREQ occurs when there is an assertion of the
start_isignal andbyte_len_iis not zero. This suggests that a new DMA operation is requested with a non-zero transfer length.
- The
-
RREQ State:
- The
arvalidsignal is asserted to initiate a read transaction. The code snippet suggests thatarvalidshould remain'1'untilarready_ifrom the slave is asserted, indicating that the slave is ready for a read transaction. - As soon as
arready_iis detected, the state transitions to RDATA andsrc_addr_nis incremented by 4 (assuming a 32-bit data width and the data is read from memory in 4-byte increments).
- The
-
RDATA State:
- The
rreadysignal is asserted, indicating that the DMAC is ready to receive data. - Two conditions are proposed:
- If
rvalid_iandrlast_iare asserted simultaneously, it means the last piece of requested data has been received and the controller prepares to switch to the WREQ state by assertingfifo_wrento push data into the FIFO. - If
rvalid_iis alone asserted (andrlast_iis not), indicating more data is forthcoming, it remains in the RDATA state, continuing to accept more data and pushing it into the FIFO.
- If
- The
-
WREQ State:
awvalidis asserted, which prompts a write transaction setup.- Upon
awready_iassertion (indicating the memory/slave is ready to accept a write transaction), the state transitions to WDATA, anddst_addr_nis prepared to be incremented, indicating the address for the next write will be advanced by 4 bytes (for the next transaction cycle).
-
WDATA State:
- The
wvalidsignal is asserted to indicate that data is ready to be written to memory. - A notable condition is when both
wready_i(indicating the slave/memory is ready to accept data) andwlast(this signal should indicate the last data in a burst) are asserted. Ifcnt(the counter tracking remaining bytes) hits zero precisely whenwlastis true, it signifies all data has been transferred, and the state can return to IDLE. Ifcntis not zero, it indicates there are more data to transfer, prompting a transition back to RREQ to fetch more data.
- The
The operation logic within each state, along with signal transactions and state transitions are accurately embodied by the system's microarchitecture as illustrated in the given waveforms and diagrams. Corrections and clarifications are provided based on the supplied source code snippet and its operation, completing the operational overview for each designated state of the DMAC engine.
-