Skip to content
TheChatArchiveThe Chat Archive
gpt-4-0125-preview· OpenAIAi2 WildChat-4.8M (AI2)

<<StartOfFile:DMAC/RTL/DMACCFG.sv>>> module DMACCFG ( input wire clk, input wire rstn,…

  1. User

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>>

    module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // ********************** 
        // ********************** 
        // FILL YOUR CODE HERE
        // ********************** 
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>>

    module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/RTL/filelist.f>> -sverilog $LAB_PATH/RTL/DMAC_TOP.sv -sverilog $LAB_PATH/RTL/DMAC_CFG.sv -sverilog $LAB_PATH/RTL/DMAC_ENGINE.sv -sverilog $LAB_PATH/RTL/DMAC_FIFO.sv <<EndOfFile:DMAC/RTL/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <<StartOfFile:DMAC/SIM/TB/filelist.f>> $LAB_PATH/SIM/TB/timescale.v $LAB_PATH/SIM/TB/AXI_INTF.sv $LAB_PATH/SIM/TB/AXI_SLAVE.sv $LAB_PATH/SIM/TB/DMAC_TOP_TB.sv <<EndOfFile:DMAC/SIM/TB/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/timescale.v>> `timescale 1ns/1ps <<EndOfFile:DMAC/SIM/TB/timescale.v>>

    <<StartOfFile:DMAC/SIM/run.compile>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf $RUN_DIR echo "Creating a new directory" mkdir -p $RUN_DIR cd $RUN_DIR echo "Compiling" $COMPILE_CMD $COMPILE_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile>>

    <<StartOfFile:DMAC/SIM/run.compile4cov>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" COV_DIR="$PWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir $COV_DIR" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf $RUN_DIR echo "Creating a new directory" mkdir -p $RUN_DIR cd $RUN_DIR echo "Compiling" $COMPILE_CMD $COMPILE_OPTIONS $COV_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile4cov>>

    <<StartOfFile:DMAC/SIM/run.sim>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e $RUN_DIR/simv ]; then cd $RUN_DIR ./simv else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim>>

    <<StartOfFile:DMAC/SIM/run.sim4cov>> #!/bin/bash

    source ../../scripts/common.sh

    COV_DIR="$PWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir $COV_DIR"

    if [ -e $RUN_DIR/simv ]; then cd $RUN_DIR ./simv $COV_OPTIONS else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim4cov>>

    <<StartOfFile:DMAC/SIM/run.verdi>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    cd $RUN_DIR $VERDI_CMD $VERDI_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.verdi>>

    <<StartOfFile:DMAC/SIM/run.verdi4cov>> verdi -cov -covdir VDB.vdb/ <<EndOfFile:DMAC/SIM/run.verdi4cov>>

    <<StartOfFile:DMAC/SIM/run.waveform>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e $RUN_DIR/dump.vcd ]; then cd $RUN_DIR $WAVE_CMD $WAVE_OPTIONS -i dump.vcd else echo "Dump file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.waveform>>

  2. Assistant

    It appears that you've provided a comprehensive set of SystemVerilog models, scripts, and related files for a Direct Memory Access Controller (DMAC) simulation project, organized into RTL and testbench (TB) components, along with scripts for compilation, simulation, and viewing waveforms or utilizing Verilog simulation tools like verdi.

    This DMAC project includes configurations for an AMBA APB interface, AXI master interface, a simple FIFO buffer, and the logic to control DMA transfers. The simulation environment is set up to test the DMAC functionality with APB configuration writes, AXI memory reads/writes, and to check the successful transfer of data from a source to a destination address in memory through the DMA engine. The simulation scripts provided include options for running the simulation with coverage, using verdi for debugging and waveform viewing using a generic waveform tool command placeholder ($WAVE_CMD).

    Given the extensive and detailed content, could you specify the type of assistance or specific question you have regarding this DMAC project? Whether it's about understanding a specific part of the code, debugging, enhancing the design, or simulation and tool-related queries, please provide more details to receive targeted help.

  3. User

    ""FILL YOUR CODE HERE"에 적절한 코드를 작성해줘."를 영작해줘.

  4. Assistant

    "Please write the appropriate code in 'FILL YOUR CODE HERE'."

  5. User

    Please write the appropriate code in "FILL YOUR CODE HERE".

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // ********************** 
        // ********************** 
        // FILL YOUR CODE HERE
        // ********************** 
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            $display("FIFO overflow");
            @(posedge clk);
            $finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            $display("FIFO underflow");
            @(posedge clk);
            $finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>>

    module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/RTL/filelist.f>> -sverilog LABPATH/RTL/DMACTOP.sv−sverilogLAB_PATH/RTL/DMAC_TOP.sv -sverilog LAB_PATH/RTL/DMAC_CFG.sv -sverilog LABPATH/RTL/DMACENGINE.sv−sverilogLAB_PATH/RTL/DMAC_ENGINE.sv -sverilog LAB_PATH/RTL/DMAC_FIFO.sv <<EndOfFile:DMAC/RTL/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        $dumpvars(0, u_DUT);
        $dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE display("Timeout!");display("Timeout!"); finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        $display("---------------------------------------------------");
        $display("IP version: %x", data);
        $display("---------------------------------------------------");
    
        $display("---------------------------------------------------");
        $display("Reset value test");
        $display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            $display("DMA_SRC(pass): %x", data);
        else begin
            $display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            $finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            $display("DMA_DST(pass): %x", data);
        else begin
            $display("DMA_DST(fail): %x", data);
            @(posedge clk);
            $finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            $display("DMA_LEN(pass): %x", data);
        else begin
            $display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            $finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            $display("DMA_STATUS(pass): %x", data);
        else begin
            $display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            $finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        $display("---------------------------------------------------");
        $display("Load data to memory");
        $display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = $random; 
            u_mem.write_word(i, word);
        end
    
        $display("---------------------------------------------------");
        $display("Configuration test");
        $display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            $display("DMA_SRC(pass): %x", data);
        else begin
            $display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            $finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            $display("DMA_DST(pass): %x", data);
        else begin
            $display("DMA_DST(fail): %x", data);
            @(posedge clk);
            $finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            $display("DMA_LEN(pass): %x", data);
        else begin
            $display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            $finish;
        end
    
        $display("---------------------------------------------------");
        $display("DMA start");
        $display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = $realtime;
    
        $display("---------------------------------------------------");
        $display("Wait for a DMA completion");
        $display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = $realtime - elapsed_time;
        $timeformat(-9, 0, " ns", 10);
        $display("Elapsed time for DMA: %t", elapsed_time);
    
        $display("---------------------------------------------------");
        $display("DMA completed");
        $display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        $display("---------------------------------------------------");
        $display("verify data");
        $display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                $display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        $display("===================================================");
        $display("= 1st trial"); 
        $display("= Copying %x bytes from %x to %x", len, src, dst);
        $display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        $display("===================================================");
        $display("= 2nd trial (long transfer)");
        $display("= Copying %x bytes from %x to %x", len, src, dst);
        $display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        $display("===================================================");
        $display("= 3rd trial (long transfer-2)");
        $display("= Copying %x bytes from %x to %x", len, src, dst);
        $display("===================================================");
        test_dma(src, dst, len);
        $finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <<StartOfFile:DMAC/SIM/TB/filelist.f>> LABPATH/SIM/TB/timescale.vLAB_PATH/SIM/TB/timescale.v LAB_PATH/SIM/TB/AXI_INTF.sv LABPATH/SIM/TB/AXISLAVE.svLAB_PATH/SIM/TB/AXI_SLAVE.sv LAB_PATH/SIM/TB/DMAC_TOP_TB.sv <<EndOfFile:DMAC/SIM/TB/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/timescale.v>> `timescale 1ns/1ps <<EndOfFile:DMAC/SIM/TB/timescale.v>>

    <<StartOfFile:DMAC/SIM/run.compile>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf RUNDIRecho"Creatinganewdirectory"mkdir−pRUN_DIR echo "Creating a new directory" mkdir -p RUN_DIR cd RUNDIRecho"Compiling"RUN_DIR echo "Compiling" COMPILE_CMD COMPILEOPTIONS−fCOMPILE_OPTIONS -f FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile>>

    <<StartOfFile:DMAC/SIM/run.compile4cov>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="PWD/../"COVDIR="PWD/../" COV_DIR="PWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir $COV_DIR" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf RUNDIRecho"Creatinganewdirectory"mkdir−pRUN_DIR echo "Creating a new directory" mkdir -p RUN_DIR cd RUNDIRecho"Compiling"RUN_DIR echo "Compiling" COMPILE_CMD COMPILEOPTIONSCOMPILE_OPTIONS COV_OPTIONS -f FILELISTTB−fFILELIST_TB -f FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile4cov>>

    <<StartOfFile:DMAC/SIM/run.sim>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e RUNDIR/simv];thencdRUN_DIR/simv ]; then cd RUN_DIR ./simv else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim>>

    <<StartOfFile:DMAC/SIM/run.sim4cov>> #!/bin/bash

    source ../../scripts/common.sh

    COV_DIR="PWD/VDB"COVOPTIONS="−cmline+cond+fsm+tgl+branch−cmdirPWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir COV_DIR"

    if [ -e RUNDIR/simv];thencdRUN_DIR/simv ]; then cd RUN_DIR ./simv $COV_OPTIONS else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim4cov>>

    <<StartOfFile:DMAC/SIM/run.verdi>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    cd RUNDIRRUN_DIR VERDI_CMD VERDIOPTIONS−fVERDI_OPTIONS -f FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.verdi>>

    <<StartOfFile:DMAC/SIM/run.verdi4cov>> verdi -cov -covdir VDB.vdb/ <<EndOfFile:DMAC/SIM/run.verdi4cov>>

    <<StartOfFile:DMAC/SIM/run.waveform>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e RUNDIR/dump.vcd];thencdRUN_DIR/dump.vcd ]; then cd RUN_DIR WAVECMDWAVE_CMD WAVE_OPTIONS -i dump.vcd else echo "Dump file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.waveform>>

  6. Assistant

    To fill in the appropriate code for the "FILL YOUR CODE HERE" section within the DMAC_ENGINE module in SystemVerilog, it's essential to understand that this section requires the implementation of a finite state machine (FSM) to manage DMA transactions. The general idea is to sequence through initial setup, data reading from the source address, data writing to the destination address, and to handle completion. Below is an example implementation focused on managing the read and write states:

    // inside DMAC_ENGINE module
    
    always_comb begin
        // Default assignments
        state_n = state;
        src_addr_n = src_addr;
        dst_addr_n = dst_addr;
        cnt_n = cnt;
        wcnt_n = wcnt;
    
        arvalid = 1'b0;
        rready = 1'b0;
        awvalid = 1'b0;
        wvalid = 1'b0;
        wlast = 1'b0;
        done = 1'b0;
        fifo_wren = 1'b0;
        fifo_rden = 1'b0;
    
        case (state)
            S_IDLE: begin
                if (start_i) begin
                    state_n = S_RREQ;
                    src_addr_n = src_addr_i;
                    dst_addr_n = dst_addr_i;
                    cnt_n = byte_len_i;
                    done = 1'b0;
                end
            end
            
            S_RREQ: begin
                if (!fifo_full) begin
                    arvalid = 1'b1;
                    if (arready_i) begin
                        rready = 1'b1;
                        state_n = S_RDATA;
                    end
                end
            end
    
            S_RDATA: begin
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1'b1;
                    rready = 1'b1;
                    if (rlast_i) state_n = S_WREQ;
                end
            end
    
            S_WREQ: begin
                if (!fifo_empty) begin
                    awvalid = 1'b1;
                    if (awready_i) state_n = S_WDATA;
                end
            end
    
            S_WDATA: begin
                if (!fifo_empty && wready_i) begin
                    fifo_rden = 1'b1;
                    wvalid = 1'b1;
                    wcnt_n = wcnt + 1;
                    if (wcnt == (cnt >> 2) - 1) begin // Assuming 4 bytes per word
                        wlast = 1'b1;
                        wcnt_n = 0;
                        state_n = S_IDLE;
                        done = 1'b1;
                    end
                end
            end
        endcase
    end
    

    This code snippet outlines the basic operation of a DMA engine moving through read and write data phases. Please note, this illustration simplifies complex aspects like address incrementing and length checking, which you'd need to adapt based on the detailed requirements of your DMA's operation. The snippet assumes 4 bytes per word in counting for the wcnt comparison, which you might need to adjust. It transitions the FSM through stages from idle to read-request (S_RREQ), read-data handling (S_RDATA), write-request (S_WREQ), and write-data handling (S_WDATA), eventually circling back to idle upon completion.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.